Cisco WAN :: Hwic-3g-hspa 1921 Giving Time Out
Jun 15, 2011I've been using hwic-3g-hspa with 1841 before but now I'm using 1921 and I'm always getting timed-out
View 1 Replies
ADVERTISEMENT
Cisco WAN :: HWIC-3G-HSPA - How To Keep 3G Connection Up As Backup
Apr 6, 2011I have many HWIC-3G-HSPA cards as backup connections and I need to keep them up for monitoring purposes. Being a backup connection they get little interesting traffic for them to spring into life but they are the source interface for a tunnel interface (we use DMVPN). The interface still insists on going down. I have even added static routes to the DMVPN hubs over the cellular interface and they still go down. What command do I enter to always keep them up? I had originally used 'dialer idle-timeout 0' and then removed it altogether which the same results. Below is what I have now.
interface Cellular0/1/0 ip address negotiated ip nat outside ip virtual-reassembly in encapsulation ppp dialer in-band dialer string gsmscript dialer-group 1 async mode interactive ppp chap hostname //username// ppp chap password //password//
ppp ipcp dns request
access-list 1 permit anydialer-list 1 protocol ip list 1
line 0/1/0 exec-timeout 0 0 script dialer gsmscript modem InOut no exec transport input all transport output all rxspeed 7200000 txspeed 5760000
Cisco Wireless :: HWIC-3g-HSPA-G Firmware Or Hardware Failing?
Dec 12, 2011Within the space of a few days we've had 2 HWIC-3G-HSPA-G cards appear to fail on different router models. In each case the sh cell x/x/x hardware output is empty i.e no firmware version or other data provided and the radio status is off. Attempts to force the interface down using the test ....modem-power-cycle or radio-power off get the same error message that the modem is still in reset. Reloading the router does not clear this so we recently tried to update the firmware using the latest version off CCO. The upgrade using the microcode commands failed with an error of "unable to determine the modem state".
View 3 Replies View RelatedCisco Wireless :: HWIC-3G-HSPA Card Was Working Properly But 3G Interface Resets
Apr 5, 2011We have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
View 1 Replies View RelatedCisco WAN :: 1921 With HWIC-3G-CDMA To Concentrator 3005?
Mar 29, 2011I have an interesting problem. I've configured a site to site VPN connection between these two devices. I am using the CDMA card as the primary and only outside connection on the 1921. What happens is that by default the cellular connection is offline. When traffic is generated internally from that network to the concentrator side of this scenario the cellular connection goes online and builds the tunnel, no problem. However, I cannot initiate the tunnel from the concentrator side. I think what i need is a way to force the cellular connection to always be on, and if it fails to come back online.
View 3 Replies View RelatedCisco WAN :: Cross Connect Between 2821 With WIC-2T To 1921 With HWIC-2T
Nov 13, 2012i have 2 routers 2821 with wic-2t serical card and 1921 with hwic-2t serial card.can i connect between those two serials card with serial cross cable ?
View 3 Replies View RelatedCisco WAN :: 1921 / 1941 - Unable To See HWIC-1DSU-56K4?
Aug 4, 2011We are currently moving from 1841 (EOL) to 1921/1941 routers. According to the module support doc [URL] this HWIC-1DSU-56K4 card is supported. We have tried both the 1921 and 1941 with the cards without any luck.
IOS Verison: c1900-universalk9-mz.SPA.152-1.T.bin
System Version: 15.0(1r)M9
Boot Error: %MAINBOARD-1-UNKNOWN_WIC: wic card in location 0/1 has an unknown id 0xB
Show Diag:
WIC Slot 1:
DSU 56K
WIC module not supported/disabled in this slot
Hardware revision 1.0 Board revision A0
[code].....
Cisco Switching/Routing :: Not Detecting HWIC-2T In 1921 Router?
Oct 15, 2012I Have installed HWIC-2T card in my cisco 1921 router but it is not able to detected in router. find the ver of router
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Tue 20-Mar-12
[Code]......
Cisco Switching/Routing :: Trunking With HWIC-4ESW On 1921?
Feb 27, 2012We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
View 4 Replies View RelatedCisco Switching/Routing :: 1921-SEC/K9 - HWIC-4ESW Compatibility
Jan 9, 2012Does Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
Cisco WAN :: 1921 - Connect Switches Via Fiber / How To Configure HWIC
Oct 30, 2011we bought the Cisco 1921 ISR with the HWIC-1GE-SFP to get a router that would be able to connect via fiber to our switches. I called Cisco and their reps recommended this router/HWIC pair to me.
I have got the basic configuration out of the way and I have discovered my router with CCP, now I would like to know how I can configure this HWIC. I have the SFP(GLC-SX-MM= ) installed correctly and it is connected to our test switch via an LC/LC cable, but when I do 'show ip interface" all ports are down except the one my workstation connects directly to the router with (gigabit0/1).
Cisco VPN :: 10 Minute Time Out WebVPN On 1921 Router?
Jun 9, 2013We have a 1921 router that has WebVPN (Any connect) enabled on it as well as IPSEC. When a user logs in using IPSEC client they stay connected no issue. IF you connect using Any Connect it will disconnect you after exactly 10 minutes. Never a second more or less. I ran some “debug webvpn” and the disconnect looks to be a planned event and reports no error it just sends the disconnect command. However, if you watch the buildup you get the following message from Debug.
003960: Jun 7 09:09:06.833 NewYork:
003961: Jun 7 09:09:06.833 NewYork:
003962: Jun 7 09:09:06.833 NewYork: [WV-TUNL-EVT]:[3318C168] CSTP Version recd , using 1
003963: Jun 7 09:09:06.833 NewYork: [WV-TUNL-EVT]:[3318C168] Allocating IP 172.18.249.50 from address-pool IPRange1
003964: Jun 7 09:09:06.833 NewYork: [WV-TUNL-EVT]:[3318C168] Using new allocated IP 172.18.249.50 255.255.255.255
003965: Jun 7 09:09:06.833 NewYork: [WV-TUNL-EVT]:[3318C168] Full Tunnel CONNECT request processed, HTTP reply created
[code]....
The highlighted entry is a session timeout set for exactly 10 minutes. I cannot find how to change, remove, or modify this setting. Google has failed me in my ability to find this timeout setting.
Cisco Switching/Routing :: IP SLA Support On 1921/K9 Or 1921-SEC/K9?
Oct 5, 2012We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
Cisco WAN :: EHWIC-3G-HSPA+7 Not Supported In Vrf Setups?
May 8, 2012we set up a 1941 with c1900-universalk9-mz.SPA.151-4.M3.binand tried to bring up EHWIC-3G-HSPA+7 in the vrf. [code]
View 4 Replies View RelatedCisco WAN :: Controlling Router Via SMS By EHWIC-3G-HSPA
Apr 21, 2013I need to make some perfomances (like up/down GRE tunnels) on Cisco ISR 2921 by sending SMS. It could be doing by using 3G modem like a Huawei and a server with some expect/SSH-scripts.
But ISR gen.2 has EHWIC-3G modules, which working with GSM networks and they can send/recieve SMS. I think, that it should be an EEM event or some another way to track comming SMS and process it by TCL-script — get a sender number, SMS body and make usefull perfomances on my router (up/down GRE tunnels in my case).
If I done this trick only by using an ISR router and EHWIC-3G module, it will be much more stable scheme in that we dont have extra components (server, modem) potentially may falls.
Unfortunately, there are too low information about configuring this modules (especially, SMS-part) and I dont find usefull for me.
Home Network :: Using 5 Ghz Networking With HSPA?
Jun 20, 2012I've recently changed my DSL connection to HSPA because of low speed of DSL connection (2000).
Anyway, I need to build up 5 Ghz networking at home but there is no dual band HSPA modem router on the market. I need a router which supports DLNA/UPnP for NAS Server. So, I have couple of solutions...
1- I can purchase dual-band Asus RT-N66U and use HSPA/UMTS stick to use this router as main router. I can do this because RT-N66U supports sticks via USB.
2- I can connect my HSPA modem to a dual-band router via LAN and by changing IP adresses I can use dual-band router again as a main modem router. This can be no problem via WAN but my modem has no WAN connection. Is this possible via LAN?
Or do you have any other solution how I can get my 5 Ghz netwroking at home using HSPA connection.
Cisco Wireless :: PCEX-3G-HSPA Searching For Drivers
Oct 11, 2011I have found in my storage a device: PCEX-3G-HSPA (attached a photo of it)
And wanted to use it, but cant find any drivers for it. My OS is Windows 7 64bit. How to make this device to work under Win 7?
Dell :: XPS L502x - Possibility To Add HSPA Mini Card
Nov 28, 2012I have a Dell XPS L502x (Core i7, 6 GB RAM, 2GB NVIDIA graphic card, 750 GB HDD)My laptop does not have HSPA mini card
Is there a possibility to add a HSPA mini card
Cisco Switching/Routing :: Configuration EHWIC-3G-HSPA-U Card On 2911
Nov 15, 2012How I configurate EHWIC-3G-HSPA+7 card on 2911.
View 3 Replies View RelatedCisco WAN :: EHWIC-3G-HSPA+7 Fail Over Between Two Connections Are Handled By IP SLA Echo And Track
Dec 3, 2012I am having problems with these types of 3G cards(EHWIC-3G-HSPA+7) from Cisco.We are using them on ships where we have a SAT connection and the 3G connection. Fail over between the two connections are handled by an IP SLA echo and a track on the cellular interface, towards an public IP where we have configured a static route to via the Cellular interface.
Once configured the connection comes up fine, the VPN tunnels comes up and all is good.But after some time the connection dies, the track goes down because no data goes through.a sh cell 0/0/0 all however say that the profile is active.
Cisco WAN :: Difference Between HWIC-1ADSL-M And HWIC-1ADSL?
Jun 12, 2013What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedDell :: 5530-HSPA-MINI - Getting Error While Downloading Driver
Sep 5, 2012i have a dell mini 10 that had ubuntu but i put vista on it and after i did it my network controller wont install and i downloaded almost every driver dell had and one worked but i had the 39 error code, the driver that worked was DELL_WIRELESS-5530-HSPA-MINI_A06_R220877 but had 39 error code
View 1 Replies View RelatedDell :: Combination Of Latitude E6410 And 5550 Module For Faster HSPA+ Networks?
Jul 25, 2012I am thinking about buying Dell 5550 module to my Latitude E6410. I know that for E6410 is designed 5540 module, but newer 5550 for E6420 has ability to use faster HSPA+ networks.
So my question is, any info on this combination of Latitude E6410 and Dell 5550 module?
Cisco WAN :: Can't Use Ehwic-3g-hspa-u Card In 2800 Series And 1841 Series Router
Jun 2, 2012why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedCisco WAN :: 2621 / Time-Based Access Lists Using Time Ranges?
Jan 4, 2011I have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedCisco Wireless :: WAP321 Lost Time - Cannot Sync With Time Server
Jul 8, 2012I just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedCisco WAN :: 1941 Router Frozen From Time To Time?
Jun 29, 2011Ciso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
Linksys Wireless Router :: Wrt54g2 Wifi Stops Working From Time To Time
Oct 26, 2011I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedLinksys Cable / DSL :: X2000 Current Time Will Not Stay Set To Time Zone
May 1, 2012I recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedLinksys Cable / DSL :: Retrieving Up-time / DSL Connection Time Information From WAG320N
Jan 17, 2012Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedD-Link DIR-825 :: Wireless Signal Drops From Time To Time?
Jan 10, 2012AI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View RelatedD-Link DIR-655 :: Wireless Network Gets Slow Time To Time
Sep 1, 2011i have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
Cisco :: DHCP Is Not Giving Ip To IPhone
Jun 26, 2012I'm still having bad time with the basic configuration I'm trying to make 2 VLANS: voice and data and run DHCP server on router hoping it will give the Ip Phone an IP address but I don't know where the problem is.
View 4 Replies View Related