Cisco Switching/Routing :: Configuration EHWIC-3G-HSPA-U Card On 2911
Nov 15, 2012How I configurate EHWIC-3G-HSPA+7 card on 2911.
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Enabling EHWIC Card Into 2911?
Feb 16, 2012I have installed a EHWIC-4ESG card into my 2911 router running IOS Ver 15.1(4)M2. When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0." Am I missing a step, do I have change something, is it not compatible (all that I have read, states that is)
View 3 Replies View RelatedCisco Switching/Routing :: Any Configuration Guide For EHWIC-4ESW Card
Jul 18, 2012Any configuration guide for EHWIC-4ESW card. Also the difference in configuration between EHWIC-4ESWG and HWIC-4ESW if any?
View 1 Replies View RelatedCisco WAN :: Can't Use Ehwic-3g-hspa-u Card In 2800 Series And 1841 Series Router
Jun 2, 2012why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedCisco WAN :: 2911 - Installing 4G Wireless Card (EHWIC-4G-LTE-V)
Mar 27, 2013We're installing a 4G wireless card (EHWIC-4G-LTE-V) in our 2911 for the first time. Upon boot-up, the IOS doesn't recognize the card (the "show inv" command doesn't list it at all). Do I need to give a command or have a certain IOS version in order for it to be recognized?
View 1 Replies View RelatedCisco WAN :: EHWIC-3G-HSPA+7 Not Supported In Vrf Setups?
May 8, 2012we set up a 1941 with c1900-universalk9-mz.SPA.151-4.M3.binand tried to bring up EHWIC-3G-HSPA+7 in the vrf. [code]
View 4 Replies View RelatedCisco WAN :: Controlling Router Via SMS By EHWIC-3G-HSPA
Apr 21, 2013I need to make some perfomances (like up/down GRE tunnels) on Cisco ISR 2921 by sending SMS. It could be doing by using 3G modem like a Huawei and a server with some expect/SSH-scripts.
But ISR gen.2 has EHWIC-3G modules, which working with GSM networks and they can send/recieve SMS. I think, that it should be an EEM event or some another way to track comming SMS and process it by TCL-script — get a sender number, SMS body and make usefull perfomances on my router (up/down GRE tunnels in my case).
If I done this trick only by using an ISR router and EHWIC-3G module, it will be much more stable scheme in that we dont have extra components (server, modem) potentially may falls.
Unfortunately, there are too low information about configuring this modules (especially, SMS-part) and I dont find usefull for me.
Cisco WAN :: EHWIC-3G-HSPA+7 Fail Over Between Two Connections Are Handled By IP SLA Echo And Track
Dec 3, 2012I am having problems with these types of 3G cards(EHWIC-3G-HSPA+7) from Cisco.We are using them on ships where we have a SAT connection and the 3G connection. Fail over between the two connections are handled by an IP SLA echo and a track on the cellular interface, towards an public IP where we have configured a static route to via the Cellular interface.
Once configured the connection comes up fine, the VPN tunnels comes up and all is good.But after some time the connection dies, the track goes down because no data goes through.a sh cell 0/0/0 all however say that the profile is active.
Cisco Switching/Routing :: 2811 And EHWIC VA DSLA Connection Configuration
Jan 22, 2012I am having trouble setting up a EHWIC-VA-DSL-A= card on my cisco 2811 running the following the following:c2800nm-adventerprosek9-mz.151-4.M2.bin and C2800NM_RM2.srec.124-13r.T11
My hardware supplier tells me its the right adsl card (have 1 existing working card not the same) but the card will not detect on the system to be configured.is this the right card? am I missing something?
Cisco WAN :: Number Of EHWIC / HWIC In 2911?
Oct 6, 2011According to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies View RelatedCisco WAN :: Can Populate All 4 EHWIC Slots In 2911 Router With VWIC3-4MFT-T1/E1 Cards
Mar 12, 2013Can I populate all 4 EHWIC slots in a Cisco 2911 router with VWIC3-4MFT-T1/E1 cards supporting clear channel T1 data traffic?Or do I need a higher performance router inthe 3900 series to do this?The data sheets lead me to the conclusion that I can but I just want to validate this.
View 6 Replies View RelatedDell :: XPS L502x - Possibility To Add HSPA Mini Card
Nov 28, 2012I have a Dell XPS L502x (Core i7, 6 GB RAM, 2GB NVIDIA graphic card, 750 GB HDD)My laptop does not have HSPA mini card
Is there a possibility to add a HSPA mini card
Cisco Wireless :: HWIC-3G-HSPA Card Was Working Properly But 3G Interface Resets
Apr 5, 2011We have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
View 1 Replies View RelatedCisco WAN :: 2921 Router Not Detecting EHWIC-1GE-SFP-CU Card
Oct 2, 2011I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?
View 1 Replies View RelatedCisco Wireless :: High CPU On 2921 With EHWIC Card?
Aug 16, 2012I am getting the following error message on a Cisco 2921 as a result of which has a there is 99 % CPU util. This router has the following cards installed and 4G WWAN EHWIC is running 15.1(4) M3 image.
EHWIC_CELL_MSG-1-EHWIC_ERROR_EVENTS: eHWIC Error Event: TxCLK PLL lost lock, HWIC slot 3
Cisco Switching/Routing :: EHWIC-1GE-SFP-CU MPLS Labeled Packets Are Not Being Processed
Dec 27, 2011We have the problem that MPLS labeled packets are not being processed on EHWIC-1GE-SFP-CU if L3PDU + Shim-Header exceeds 1500 bytes.When we move the config exactly to the on-board Interface Gi0/0 it works with put any problems. [code]
View 1 Replies View RelatedCisco Switching/Routing :: Configuring 1941 With 8 Port EHWic Switch Module And Onboard GE Ports In Single LAN?
Jul 1, 2012Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
Cisco Switching/Routing :: 2911 With IOS Version Is 15.1 - Routing Table Not Updating
Oct 2, 2012I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View RelatedCisco WAN :: 2911 Does Not Support NM-E3/T3 Serial Card?
Jun 14, 2011From all of the documentation I am seeing, the 2911 does not support the NM-E3/T3 serial card.
View 16 Replies View RelatedCisco WAN :: Which Type Of HWIC Card Should Use In 2911-sec / K9 Router
Feb 14, 2012I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
View 1 Replies View RelatedCisco Switching/Routing :: How To Install New IOS 15.1 On 2911
Dec 12, 2011i downloaded and transfered the new ios to the 2911, but no install routine started.
View 3 Replies View RelatedCisco Switching/Routing :: Enabling SSL-VPN On 2911
Nov 19, 2012after installation of demo versions of 2900-SEC-TEMP & 2911-2921-SSLVPN-TEMP & rebooting the 2911 router I do not have access SSL commands.Show license indicates that 2900-SEC-TEMP & 2911-2921-SSL-TEMP licenses are active but NOT IN USE.
View 1 Replies View RelatedCisco WAN :: Does VWIC2-2MFT-T1/E1 Card Work With 2911 Router
May 5, 2011I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies View RelatedCisco Switching/Routing :: 2911 SFP Interface Number
Apr 19, 2012I am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
Cisco Switching/Routing :: 2911 - Allow Traffic Between Two LAN Interfaces?
Nov 15, 2011I have a 2911 router. One interface is configured external (WAN) and two interfaces are configured on separate internal private subnets. What is the configuration to allow all traffic in both directions between the two internal subnets?
View 21 Replies View RelatedCisco Switching/Routing :: USB Console Into 2911 Router
May 19, 2013I have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies View RelatedCisco Switching/Routing :: 2911 IP SLA Commands Missing?
Nov 13, 2011I've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
Cisco Switching/Routing :: Redundancy Between One 2911 And Two 2960?
Aug 2, 2012we are in the planning phase for a network upgrade. We have two C2960 Switches connected via one (L2) Etherchannel (4x1 Gbit/s) which works very well. In the next phase we would like to upgrade our router to an 2911 series which has 3 gb interfaces. and indeed we would like to create an etherchannel as well. our plan is to use 2 of the 2911 to connect to the first 2960 switch and the one left to the other 2960. i think we will achieve some redundancy with this config.
View 6 Replies View RelatedCisco Switching/Routing :: 2911 - Dynamic IP From Provider
Feb 19, 2013connected DSL directly to 2900 series router , but as DSL public IP is not static (dynamic) its difficult to access Router when out of home, any other means to access router without static IP
View 2 Replies View RelatedCisco Switching/Routing :: No Serial Connections With 2911
May 8, 2011I have 2 2911 routers that will be connected via fiber with an ethernet Gig handoff to each router. Each router will then be connected to local networks on a second ethernet interface on the router. I have always connected routers via serial connections so this is new to me. Outside of the usual ethernet interface addressing configuration, is there anything else that would need to be configured on the 2 routers?
View 1 Replies View RelatedCisco WAN :: Configuring HWIC-2SHDSL Card In A 2911 For CO Mode Operation?
Dec 12, 2011I am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
Cisco Switching/Routing :: 6509 Convert CatOS Configuration To Native IOS Configuration
Jul 17, 2012I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
Cisco Switching/Routing :: 2911 Can Support Ip Service Image
Feb 29, 2012i want to check if cisco2911-sec/k9 can support IP service image? what PAK(license) can be bought to activate the IP service feature set?
View 1 Replies View Related