I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 RepliesI'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.
[URL]
I'm going to be swapping out a WIC-1DSU-T1-V2 for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
configuration examples for the two T-1 setup ?
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?
Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 1 Replies View RelatedI think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
Router 1-----
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
(code)
I have been advised by my service provider that to do ATM IMA I need an AIM-ATM and a VWIC2-2MFT-T1/E1 card, and that IMA is not support on the VWCI2-2MFT-G703 card.
View 5 Replies View Relatedi have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
View 9 Replies View Relatedthe VWIC2-2MFT-T1/E1 hardware installation guide?
View 1 Replies View RelatedI have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
We have a cisco 3825 router with OS version 12.4 and one VWIC2-2MFT-T1/E1 card at Slot 0. Now I have to add one more card of the same type in the router.
I need to know the steps or process to add the the 2nd card in the router.
VWIC2-1MFT-T1/E1 card support on 1841 Router ?any ios up-gradation required?
View 1 Replies View RelatedWe have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
[Code]....
I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
View 1 Replies View Relatedwhether a Cisco Router 2911 would work on images other than universal image. This is the question raised by one of our customer. He has 2811 Router where-in he has configured T1/E1 configuration, terminated to Zyxel Modem and working fine. Now he wants to replace this 2811 router with 2911 router. Since the universal image in 2911 router is not working with the present configuration in 2811 router, he wants to know, what options are there for him to configure this in 2911.
View 2 Replies View RelatedFrom all of the documentation I am seeing, the 2911 does not support the NM-E3/T3 serial card.
View 16 Replies View RelatedWe're installing a 4G wireless card (EHWIC-4G-LTE-V) in our 2911 for the first time. Upon boot-up, the IOS doesn't recognize the card (the "show inv" command doesn't list it at all). Do I need to give a command or have a certain IOS version in order for it to be recognized?
View 1 Replies View RelatedI have installed a EHWIC-4ESG card into my 2911 router running IOS Ver 15.1(4)M2. When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0." Am I missing a step, do I have change something, is it not compatible (all that I have read, states that is)
View 3 Replies View RelatedWill this wireless card work with a N wireless router?
View 2 Replies View RelatedI am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
How I configurate EHWIC-3G-HSPA+7 card on 2911.
View 3 Replies View RelatedApple TV doesn't work over WiFi provided by WLC installed on ISM-SRE-300 module.
Apple TV server and iPad are situated in one L3 segment, Ipad can ping Apple TV
WLC and 2911 router are configured according to this docURL
Router 2911
Version 15.2(2)T
WLC
7.0.230.0
Vlan 1 and vlan 50 (for clients) are configured on 2911 router.
I have installed a VWIC2-1MFT-G703 module into cisco 2921 router, I can verify the card by show inventory command. but in show run, I do not see the E1 controller card there. this card is used for TPG lease line for data only. Those card is compatible with new 2921 router? or need some extra command to bring it up?
View 2 Replies View RelatedI have a 2911 router inside our network with both DHCP and DNS enabled. Everything works fine except since we use this router we are not being able to go to the network neighbourhood in Windows and look up machines by name (or typing \diskstation for example). Connecting by IP works fine but not by local machine names.
View 10 Replies View Relatedi have an old hp ipaq pocket pc (really old) but a long time ago i used to have it set up wirelesly to the internet via a D-link DCF-650 W cf card. But i can't get it to find and wireless connects. The card lights aren't flashing there just on they used to flash when I would send or receive data. I can hook to internet through my computer but i want it wireless. I found some drivers for card that i installed through win7 on computer, but how do i make it install to my pocket pc where the card is at?
View 2 Replies View RelatedI have new google internet TV. It seems to only work if connected to an ethernet line directly vs my 4G wifi card.
View 1 Replies View RelatedI am trying to find out what Wi-Fi card will work with an inspirion 531S. Tech and sales support on dell sight didn't assist much, just gave me links to a bunch of cards.
View 2 Replies View RelatedI have a Belkin usb adapter to pick up my wireless internet. problem is when i choose my network to connect to it constantly says "acquring network address". But as soon as i plug in an ethernet cable from the router the wireless starts working and i just unplug the ethernet cble. So why does my wireelss card depend on my ethernet conenction?
View 7 Replies View RelatedDell 8400 - Vista - TWO 1GB 4200/&NBST 533MHz and TWO 512 5300 667MHz
If I install one matched pair, the wireless network is found and will connect to the network. If I install all four, the network is not found and the wireless will not connect. The network card is Netgear G PCI adapter 54MBTS 2.4GHz.
I recently re-installed Windows XP on my computer,
I re-installed the drivers, but my wirless card does not work,
The Dell wirless program states the radio is disabled press Fn-F2 to activate it
Fn-F2 has no effect.
I have a dell Inspiron 8000. The computer will not detect the onboard ethernet jack? It does not show up in the devices list. The lights for activity will not come up when I plug an ehternet cable in to it either..
View 7 Replies View RelatedI have a VWIC2 running two T1 circuits to two locations. Can I put the controllers on the same channel group? I also have a PPP multilink controller on a VWIC2 on channel group 0.
View 2 Replies View RelatedHow to successfully get a Dell Wireless 1397 to work with Windows 2008 x64? I have a Precision M4500 that I managed to install Windows 2008 x64 R2 on. I installed the Windows 7 drivers for the card and the Device Manager says the device is working properly. But when I go to enable the device, it acts like it is enabling it, but the properties always say "disabled".
View 1 Replies View RelatedI have checked and re-checked before buying and this card is evidently supported on the 1841 for 'data mode only' which is all I need. I have 3 T1s in Multilink mode and I want to use 2 of these cards (and 3 of the 4 ports) to support it. The problem is that even though SH INVENTORY finds the card, I can't issue the "card type" command to indicate I am using it with a T1 - I get this:
R3(config)#card type t1 1 0
^
% Invalid input detected at '^' marker.
So I tried to issue the "controller T1" command and it does not recognize the slot as containing a T1 card (which makes sense since the "card" command did not work).
I found numerous references to this card being supported in Cisco docs with a minimum OS around 12.2(8) - it varies based on the chassis. I can't find the explicit OS required for the 1841 which is a concern but I am using 12.4(13r)T. SH VERSION finds "2 Channelized T1/PRI ports" which is the MFT card.
I need to get Serial interfaces configured on these cards.