Cisco WAN :: 3945 Router Not Detecting VWIC3-2MFT-T1/E1 Voice Card

Dec 3, 2012

We have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
 
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.

[Code]....

View 8 Replies


ADVERTISEMENT

Cisco WAN :: Drop-Insert On Vwic3-2mft-t1 / E1?

Jan 30, 2013

I have a problem with configuring of my vwic3-2mft-t1/e1 card on Cisco 2821 router. I need drop some raw data timeslots from E1 frame and then insert them into frame on other port. I enter the following commands:
 
card type e1 0 0
 controller e1 0/0/0
tdm-group 0 timeslots 1-4
clock source line
 controller e1 0/0/1
tdm-group 2 timeslots 1-4

[code]....

I find these commands in Cisco 1 and 2-port T1/E1 Multiflex Voice/WAN Interface Cards for the Cisco 1700 Series Router configuration guide for vwic2 cards.But this config is not working properly. show connect output is showing status of connection "UP", show controller e1 shows no errors on both e1 ports, but data not flows between ports.What am I doing wrong? Have vwic3 and vwic2 cards different configuration procedures or not?

View 1 Replies View Related

Cisco WAN :: 1921 And VWIC3-2MFT-t1 Support?

Mar 7, 2013

I was just given a task to setup some T1 connections. We rarely use T1 interfaces anymore as they are typically just not enough anymore. I see the newer vwic3 interfaces are supported on various 2900 series but downloaded the vwic3 configuration guide and noticed that the 1900 series routers were not in the list? Is this correct. So are vwic3-2mft-t1 ehwic cards supported or not on 1921 routers? i can see the controller interfaces but not the ports as there must be additional configuration required. Im running 15.1(4)M4 IOS version that looks to be supporting the cards.

View 2 Replies View Related

Cisco WAN :: Cannot Configure A Voice-port On Router 3945

Dec 21, 2012

When I try to configure a voice port (like voice-port 0/0/0:15) after doing a conf t, it gives me an error of invalid input detected.We are using a Cisco 3945. We have successfully setup 3825 and 2851 in the past.

View 2 Replies View Related

Cisco WAN :: Does VWIC2-2MFT-T1/E1 Card Work With 2911 Router

May 5, 2011

I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.

View 1 Replies View Related

Cisco WAN :: 3845 - Correct To State That VWIC2-2MFT-T1/E1 Can Support Data In Addition To Voice

May 10, 2013

I have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
 
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?

2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?

3. Do I just add the card, configure the new slot, and add it to the same channel group?
 
Below is the current config regarding the existing card HWIC:
 
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200

[code]...

View 1 Replies View Related

Cisco Switching/Routing :: Configuring VWIC3-4MFT-T1/E1 Card?

Jul 24, 2012

Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.

View 1 Replies View Related

Cisco WAN :: 2921 Router Not Detecting EHWIC-1GE-SFP-CU Card

Oct 2, 2011

I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?

View 1 Replies View Related

BT Homehub Not Detecting Network Card?

Feb 1, 2011

I have just given my Mum an old Dell desktop computer of mine. She has BT Broadband with a Homehub. I have connected everything up and installed the Homehub software on the computer but when it tries to search for the network connection via the BT software, it keeps saying the network card can not be detected. The network cable is plugged in and working. All the drivers are up to date.

View 14 Replies View Related

Windows Not Detecting Wireless Card?

May 30, 2012

Just re-installed windows on a laptop i got, i got all the drivers installed, but i cant seem to get the wireless card to show up, i know it has wireless because it was my moms laptop before she got a new one. Ive gone to dell support site and literately downloaded all the drivers on the page. Device manager doesn't seem to be detecting the card at all, the dell Wlan utility wont even start ive reinstalled the driver multiple times i even tried the intel site for drivers.

The big problem is i don't know what wireless card it is and its hard to find out because the support pdf for the laptop shows multiple possible cards.

[URL]

View 6 Replies View Related

New Wireless Card Not Detecting Available Networks?

Jun 16, 2012

I have a Compaq Presario R3000. It did not hav a wireless card or antenna. I purchased and installed all. I uploaded the drivers and there are no ssues(apparent) with the drivers.I have a Broadcom g Network Adapter. Windows Zero Configuration is started and set to automatic. I reset WINSOCK entries to installation defaults using netsh winsock reset catalog and I rebooted.I am lost and don't know what else to check. Also, this machine doesn't have a wifi button that I can see but the card is

View 3 Replies View Related

Cisco WAN :: 3945 Use T3 Functionality / Enabled Command Card Type T3 1

Feb 10, 2011

We purchase a new 3945 router and a NM-1A-T3/E3 card. We would like to use the T3 funcationality so we enabled the command card type t3 1 (slot1), reboot the device.After reboot the sh ip int brief command should show the serial interfaces e.g serial1/0.In this case it doesn't, it shows the Gigi interfaces and ATM1/0 no serial interfaces.I've also tried upgrading to the latest IOS from cisco.

View 2 Replies View Related

Cisco WAN :: Does RF Section Of Part Number Differentiate From NM-T3 / E3 Card 3945

Jul 19, 2012

We have a NM-T3/E3-RF card that fits inside a 3800, but does not fit into a 3945.  
 
The documentation says it works with 3900 ISR Routers.
 
Is there a cradle or adapter that is required?
 
Does the "RF" section of the part number differentiate this from a NM-T3/E3 card?   

View 5 Replies View Related

Cisco WAN :: 3845 / 3945 - NM-16ESW-1GIG Card Configuration?

Sep 30, 2012

I have 3945 Router and I have bought NM-16ESW-1G1G card. After installed the card no interface  shows on show ip interface brief or Show run command . When i end the switch module then i have found the interface. previously i have worked on NM-16ESW card on my 3845 router where interface card interface shows in my show run and interface command and i have assign IP and crypto map fro my Branch.
 
So my question is NM-16ESW-1G1G is different then NM-16ESW card ? if not then why i can not find interface. if Different then i have need to configure interfcae by enter the switch module seperately ? 

View 7 Replies View Related

Cisco WAN :: 2811 With WIC-1T Card Detecting RS530 Cable As DTE 530idb?

Feb 25, 2011

I am facing the problem as my CISCO router is detecting the RS 530 DCE cable as DTE 530idb. I am using this cable for X25 link connectivity. The same cable has worked for more than 1 hour with detecting the cable type as 530 DCE, but suddenly it stops the X25 data transfer. After that the cable type it is showing as DTE 530idb.
 
Below troubleshooting already carried out.
 
1. Changed the slot, but same output.

2. Removed the cable & reconnected, but same output.

3. Without connecting to the DTE device also, the cable type is showing as DTE 530idb

View 1 Replies View Related

Laptop Not Detecting Wireless Networks / WLAN Card Disabled

May 19, 2012

When I click on the Wireless Network Connection icon it says "Wireless network unavailable." There's also an error message that says "The Dell Wireless WLAN Card is disabled. Use the Dell Wireless WLAN Utility to enable it." When I right click on the wireless network icon it says "No wireless networks were found in range. Make sure the wireless switch on your computer is on. To see an updated list, click 'Refresh network list.'" I don't have a wireless switch. I have a wireless enable icon and it says Enabled. My wireless network is working because my phone sees it and two other networks in the neighborhood. I couldn't find the Dell Wireless WLAN Utility. I also tried my iPhone hotspot. Laptop did not detect it either.

View 2 Replies View Related

Cabling / Cards :: Why Does Task Manager Not Detecting Network Card

May 15, 2012

I open up the task manager and it does not detect my network card even though it is inserted correctly

View 7 Replies View Related

Cisco WAN :: Can Populate All 4 EHWIC Slots In 2911 Router With VWIC3-4MFT-T1/E1 Cards

Mar 12, 2013

Can I populate all 4 EHWIC slots in a Cisco 2911 router with VWIC3-4MFT-T1/E1 cards supporting clear channel T1 data traffic?Or do I need a higher performance router inthe 3900 series to do this?The data sheets lead me to the conclusion that I can but I just want to validate this.

View 6 Replies View Related

Cisco :: BRI Card Does Not Show In (show Voice Port)

Jun 18, 2011

I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.

View 4 Replies View Related

Cisco WAN :: C2901 VWIC3-1MFT-T1 / E1 Frame Relay?

Dec 18, 2011

IOS  15.1(4)M1.
 
I am trying to setup my new 2901 running  15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card.  Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s.  None of the commands I am used to seem to even exist.  None of the
 
encapsulation frame-relay ietf 
frame-relay interface-dlci 16 ietf
 
seems to be there. How to configure the card in IOS 15?

View 1 Replies View Related

Cisco WAN :: 3945 Router CPU Temperature?

Nov 8, 2012

I am trying to find out what the 'normal' operating temperature of the CPU in a 3945 router is? We have just replaced some 2800 routers for 3945's and the NMS server initially complained about the new router CPU temperature being too high.  Compared to the 2800 the CPU temperature is much hotter - 50 degrees celcius as opposed to 20-smothing degrees.  I have searched but can't find what are considered 'normal'?
 
This is the output:
 
router#sho environment allSYSTEM POWER SUPPLY STATUS==========================Internal Power Supply 1 Type: DCInternal Power Supply 1 12V Output Status: Normal

[Code].....

View 3 Replies View Related

Cisco :: Upgrade A Router From A 2811 To A 3945?

Nov 10, 2011

I need to upgrade a router from a 2811 to a 3945.

2811 has the following modules:

View 1 Replies View Related

Cisco WAN :: 3945 Router NAT Output Interpretation?

Oct 3, 2012

I have some lags on my 3945 router. From show ip nat statistics there is following output:
 
BR1#show ip nat statistics
Total active translations: 20 (0 static, 20 dynamic; 20 extended)
Peak translations: 8877, occurred 1w0d ago
Outside interfaces:
  GigabitEthernet0/0, GigabitEthernet0/1

[code].....

View 1 Replies View Related

Cisco WAN :: URL Based Filtering In Router 3945

Jan 15, 2013

Is Cisco 3945 router support URL based filtering . For example to block website [URL] but not the main site [URL].

View 1 Replies View Related

Cisco WAN :: Access-list On Router 3945

Mar 15, 2012

I reported a really strange issue on a Cisco Router 3945. Here below info about release software used: [code] Please look at a brief extract of router running configuration file: [code] It’s an easy configuration of Extended ACL and the application on an Ethernet interface. The expected result is:

- The interface works properly (because access list is permitting every kind of data traffic in input)
- Checking “show access-list 180”, the counter of matched packets increments for all the packets that are forwarded inside the fa0/0/1.
 
But actually the Fastethernet 0/0/1 drops all the packets as if all the packets don’t match with access list (And this behavior is really incredible). The interface couldn't be used anymore because any kind of data traffic is denied.

View 14 Replies View Related

Cisco WAN :: 3945 Router IOS For VoFR Feature?

May 18, 2011

3945 Router IOS Required  for support VoFR Feature

View 1 Replies View Related

Cisco WAN :: 3945 Router And E3 / T3 Network Cards

Aug 11, 2011

I just got my first  3945 router and E3/T3 Network cards and when I do a sho ver I can see the E3/T3 card but when I do a show run all I see are the 3 GE interfaces.

View 1 Replies View Related

Cisco WAN :: Router 3945 Log To Get 100 Mbps As Sum Of Tunnels

Aug 9, 2011

I am getting the following message from a 3945 router: %CERM-4-TX_BW_LIMIT: Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license.
 
That router has 8 Gre/IPsec tunnels and one of those tunnels is 100Mbps.The question is, could I get 100Mbps as the sum of all tunnels, or is there a restriction to 85Mbps ??

View 2 Replies View Related

Cisco WAN :: Configuring Two T-1s On VWIC2-2MFT-T1/E1

Aug 7, 2011

I'm going to be swapping out a WIC-1DSU-T1-V2  for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
 
configuration examples for the two T-1 setup ?
 
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?

View 4 Replies View Related

AT&T Router Not Detecting Linksys 2 4 Ghz In Laptop?

Jan 20, 2012

at&t router not detecting linksys 2 4 ghz in laptop -- laptop can connect everywhere but my home -- other laptops and notebooks in house are connected

View 1 Replies View Related

Cisco :: 3945 Router Error While Adding In CiscoWorks

May 29, 2010

I have a Cisco 3945 Router and when we try to add the same into the Cisco Works it gives me an error saying " CM0056 Config fetch failed for 192.168.xx.xx Cause: CM0204 Could not create DeviceContext for 1238 Cause: CM0206 Could not get the config transport implementation for 192.168.xx.xx Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.
 
We are using LMS version 2.6. Any info on the latest router 3945 with support or not.

View 6 Replies View Related

Cisco WAN :: 3945 / How To Remove A File With SNMP From Router

Dec 10, 2012

On a 3945 voicegateway,I want to remove a wave file (announcement), with the purpose that a new one can be automaticaly downloaden from UCCE to the box.Is there a way to do that automaticaly with SNMPSET <voicegateway> <MIB OID> <??wave file name??> <reload>
      
EDIT: or clear the cache, which it should be I think. (all wave file cache, or only one file, not sure what should be used and/or what is possible

View 1 Replies View Related

Cisco Switching/Routing :: VPN Configuration For 3945 Router

Dec 2, 2012

the router IPSec VPN config for remote users using Cisco VPN Client 5.0.07
Router 3945 IOS C3900-UNIVERSALK9-M Version 15.1(4)M4

Here is VPN related config part and log from router and client.
 
aaa new-model
!
!
aaa authentication login default none
aaa authorization network default none
!
!
crypto isakmp policy 5
encr aes 256
authentication pre-share
[Code]...
 
I highlighted strings with possible problems of of unabling to connect but doesn't know what to do with it.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved