Cisco WAN :: Drop-Insert On Vwic3-2mft-t1 / E1?
Jan 30, 2013
I have a problem with configuring of my vwic3-2mft-t1/e1 card on Cisco 2821 router. I need drop some raw data timeslots from E1 frame and then insert them into frame on other port. I enter the following commands:
card type e1 0 0
controller e1 0/0/0
tdm-group 0 timeslots 1-4
clock source line
controller e1 0/0/1
tdm-group 2 timeslots 1-4
[code]....
I find these commands in Cisco 1 and 2-port T1/E1 Multiflex Voice/WAN Interface Cards for the Cisco 1700 Series Router configuration guide for vwic2 cards.But this config is not working properly. show connect output is showing status of connection "UP", show controller e1 shows no errors on both e1 ports, but data not flows between ports.What am I doing wrong? Have vwic3 and vwic2 cards different configuration procedures or not?
View 1 Replies
ADVERTISEMENT
Mar 7, 2013
I was just given a task to setup some T1 connections. We rarely use T1 interfaces anymore as they are typically just not enough anymore. I see the newer vwic3 interfaces are supported on various 2900 series but downloaded the vwic3 configuration guide and noticed that the 1900 series routers were not in the list? Is this correct. So are vwic3-2mft-t1 ehwic cards supported or not on 1921 routers? i can see the controller interfaces but not the ports as there must be additional configuration required. Im running 15.1(4)M4 IOS version that looks to be supporting the cards.
View 2 Replies
View Related
Dec 3, 2012
We have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
[Code]....
View 8 Replies
View Related
Sep 11, 2012
I have a working configuration with a 2811 router at my remote site in which I take the T1 (point-to-point PRI) into port 0/0/0 on the dual-port vwic2-mft-t1/e1 card. Then I plug my PBX into the 0/0/1 port. I channelize the T1 so 1/2 of the channels are used for data (13-24) and channels 1-8 are passed through the vwic2 to the PBX. I'm using the connect tdm t1 0/0/0 0 t1 0/0/1 0 command to pass the voice calls through to the PBX.
I tried to upgrade the router to a 2911 with the same card and the same configuration copied and pasted over and as soon as I put the connect tdm t1 0/0/0 0 t1 0/0/1 0 statement in, I drop the data side of the T1 and lose my connection to the WAN. If I take the command back out, the WAN still doesn't come back up until I reboot the router.
Has the syntax changed? I have a case open with TAC but so far no luck, as they can't seem to figure out which group should take this case, voice or data..
View 1 Replies
View Related
Dec 18, 2011
IOS 15.1(4)M1.
I am trying to setup my new 2901 running 15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card. Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s. None of the commands I am used to seem to even exist. None of the
encapsulation frame-relay ietf
frame-relay interface-dlci 16 ietf
seems to be there. How to configure the card in IOS 15?
View 1 Replies
View Related
Jul 24, 2012
Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.
View 1 Replies
View Related
Nov 13, 2012
We are using an ACE engine module(ACE20-MOD-K9) provide loading balancing service for two WEB servers and configured cookie for stickness. Below is the current configuration and it seems working fine now.
The problem I was facing is before use parameter-map change the http header length to 8k the stickness doesn't really working properly. User complains that their working session constantly be kicked out and redirect them to login page. By tracing traffic from a client we found that sometime ACE fails or stop insert the configured cookie, after increase the header length ACE start getting work.
how does the header length setup effect ACE to insert a cookie? Will the cookie insert attmpt fail if the header is longer then the maximum length configured on ACE? [code]
View 1 Replies
View Related
Mar 12, 2013
Can I populate all 4 EHWIC slots in a Cisco 2911 router with VWIC3-4MFT-T1/E1 cards supporting clear channel T1 data traffic?Or do I need a higher performance router inthe 3900 series to do this?The data sheets lead me to the conclusion that I can but I just want to validate this.
View 6 Replies
View Related
Nov 22, 2012
I'm living in a student flat, where each student has his own room.Every room has an LAN outlet in the wall on which he is able to connect 1 device.If you like to connect more devices, we are advised to utilize a router.Our ISP gives us the right to only use 1 MAC-adress (for safety reasons), so there the router comes into play.I have a Belkin G+ wireless router on which i would like to connect my phone and laptop by a wireless configuration and my TV (Toshiba 40TL933) by wire.My laptop and phone work like a charm.When i insert my TV to the network, the whole thing collapses.My ISP provided me with the information that i connected 2 MAC-adresses and therefore, i was cut off.This would be because of the fact that belkin routers (apparently) are notorious for providing more than 1 MAC adres.When i asked for the MAC-addresses, they gave me back these 2: * 00:00:00:00:00:00 * 00:17:3f:0d:77:f5The second one is from my Router.But where does the 00.00. etc come from?
View 5 Replies
View Related
Jan 9, 2013
I have an ACE version A5.2 configured in one-armed leg (doing source nat). I have a requirement to add(or copy) the "referer" header value from the original request to the request send by ACE.
I cannot figure out how to copy this value. It is easy to add the source ip address by adding: " insert-http x-forwarded-for header-value "%is".
So how I am going to copy the Refere header?
#Referer
#Address (URI) of the resource from which the URI in the request was obtained
View 2 Replies
View Related
May 5, 2013
We are using Cisco ACE 4710 to load balance servers. We have created VIP under the interface vlan using nat-pool command. Also, we have changed the gateway of the server to point to the ACE vlan ip address which is created using alias 10.x.x.x 255.x.x.x command under the interface vlan. In short ACE is in inline mode for the servers which needs to be load balanced.
[code]...
But still I am not able to view the original client IP. Just to add more, the site is a HTTPS site & we have not doing any kind of SSL offloading on the ACE, it is taken care by server itself
I just want to do the HTTP & HTTPS load balancing without SSL offloading & should be able to see the original client IP in the server logs
View 1 Replies
View Related
Sep 26, 2011
I got a Cisco C880 router( IOS version: 15.1(2)T1 ) with PCEX-3G-HSPA-G card installed When I insert my 3G card and issue show cellular 0 network, I found that the network is not my 3G card ISP, may i ask how can I manual select the ISP?
View 1 Replies
View Related
May 22, 2013
while the 3560 switch is running? Is it hot-pluggable?
WS-C3560X-48P is the switch and I would be adding a C3KX-PWR-1100WAC
View 1 Replies
View Related
Sep 26, 2011
Is it possible to insert a Netgear wireless router b/g 108Mbs into a running 2008r2 network, making it a slave to allow wireless access?
At the moment the menu is only accessible thru 192.168.0.1, but I need to have it visible as a device subservient to 10.151.48.1? If this is possible, I can set it up to do a SSID broadcast for wireless access?
View 9 Replies
View Related
Aug 7, 2011
I'm going to be swapping out a WIC-1DSU-T1-V2 for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
configuration examples for the two T-1 setup ?
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?
View 4 Replies
View Related
Jan 13, 2013
I have checked and re-checked before buying and this card is evidently supported on the 1841 for 'data mode only' which is all I need. I have 3 T1s in Multilink mode and I want to use 2 of these cards (and 3 of the 4 ports) to support it. The problem is that even though SH INVENTORY finds the card, I can't issue the "card type" command to indicate I am using it with a T1 - I get this:
R3(config)#card type t1 1 0
^
% Invalid input detected at '^' marker.
So I tried to issue the "controller T1" command and it does not recognize the slot as containing a T1 card (which makes sense since the "card" command did not work).
I found numerous references to this card being supported in Cisco docs with a minimum OS around 12.2(8) - it varies based on the chassis. I can't find the explicit OS required for the 1841 which is a concern but I am using 12.4(13r)T. SH VERSION finds "2 Channelized T1/PRI ports" which is the MFT card.
I need to get Serial interfaces configured on these cards.
View 5 Replies
View Related
Oct 10, 2012
Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 1 Replies
View Related
Jun 15, 2011
I think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
Router 1-----
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
(code)
View 1 Replies
View Related
Jul 19, 2012
I'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.
[URL]
View 6 Replies
View Related
May 3, 2011
I had to dig this stuff out of storage and cobble together a router on short notice. I installed this WIC into a 2821 and I can see it when I do a show ver.
Cisco 2821 (revision 53.51) with 249856K/12288K bytes of memory.Processor board ID FTX1006C0P32 Gigabit Ethernet interfaces2 Channelized T1/PRI ports <-----------------------------1 Virtual Private Network (VPN) ModuleDRAM configuration is 64 bits wide with parity enabled.239K bytes of non-volatile configuration memory.125440K bytes of ATA CompactFlash (Read/Write)
When I do a sho run I see this:
controller T1 0/0/0 framing esf linecode b8zs!controller T1 0/0/1 framing esf linecode b8zs
How do I configure IP interfaces on it though? It doesn't seem to show up as Serial ports on a sho int. Am I doing something wrong?
View 2 Replies
View Related
Sep 22, 2011
I have been advised by my service provider that to do ATM IMA I need an AIM-ATM and a VWIC2-2MFT-T1/E1 card, and that IMA is not support on the VWCI2-2MFT-G703 card.
View 5 Replies
View Related
Mar 8, 2011
i have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
View 9 Replies
View Related
Apr 11, 2005
I have a 2811 that I'm in the process of turning-up to support a 4xT1 using VWIC-2MFT-T1's. The question is how to "correctly" set clocking on the MFT's.
As is typical of the 2MFT's, as soon as a 2nd T-1 on a VWIC-2MFT comes up, I start taking "Slip Sec"s on the 2nd T-1. I have tried different clock source combinations, including "clock source line primary", various "network-clock-participate" (or not) combinations, and about a dozen other stab-in-the-dark configurations. Before I started playing with it, the slips were consistently every 9 seconds. After playing with it, I got them to every 18 seconds. But there shouldn't be ANY. So the question is what SHOULD the correct timing configuration be on that platform?
The VWIC-2MFT-T1's are in slots 1 and 3, so the controllers involved are 0/1/0, 0/1/1, 0/3/0 and 0/3/1.
View 9 Replies
View Related
Aug 10, 2011
the VWIC2-2MFT-T1/E1 hardware installation guide?
View 1 Replies
View Related
Jan 12, 2011
How do I configure a data T1 serial link on a router using IOS 15 and a VWIC3-1MFT-T1/E1 module. The "interface serialx/x/x" are not there anymore?
View 1 Replies
View Related
May 5, 2011
I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies
View Related
Apr 29, 2012
I am trying to use the connected WIC2-2MFT, as the servial interface on my cisco 1841.But it does not show me the option, under configuration interface
[code] What should I do to make this enable on this list?I am attaching the show tech-support, and show version of this device.
View 5 Replies
View Related
Sep 13, 2012
We have installed a VWIC-2MFT-T1 interface card into our 1841 router and the interface doesn't show up in CP. # we only need it for data. #
ROM version 12.4(13r)T, RELEASE SOFTWARE
All indications from my research show that this version should support this card, for data only.
why I can't see this card when I show interfaces?
View 5 Replies
View Related
May 10, 2013
I have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
View 1 Replies
View Related
Mar 28, 2012
I was trying to implement stickiness based on cookie. Server inserts a cookie and sends it to the browser. I learned from app team that this cookie is changing dynamically during the session, so stickiness based on server’s cookie doesn’t work.
Now I want to investigate into possibility of ACE to insert a cookie. My question is: ACE feature of “cookie insert”: does it add additional cookie into http header without removing server cookies or it deletes the cookie(s) that server put into http header and replaces them with its own cookie?
View 1 Replies
View Related
Sep 15, 2012
As per CISCO QoS document URL, IOS from 12.2(13)T support drop command in policy map. But our CISCO ASR 1013 having IOS of Version 15.2(1)S1 doesn't have drop syntax.How can we drop specific application using QoS in ASR 1013 of IOS version 15.2 and higher?,Can I allow few users for a particular application (like P2P) and drop other users based on users source IP?
View 2 Replies
View Related
May 22, 2012
I having a basic query in troubleshooting E1 link , here im facing packet drop in the link and we are testing by providing local loop and remote loop from the CSU/DSU at local point and at remote point . I have tried ping test while the loop is given at local point and remote point ie i have pinged my local serial interface IP address (eg 10.0.0.1 -local & 10.0.0.2 -remote ) in Remote Loop i could see no errors and drops and also the traffic on the interface output and input is the same(eg input rate 1000bps and output rate 1000bps) .My query is that when i am pinging the local interface IP does the icmp packet travels till the loop point and comes to the same interface(like a boomerang) .
ICMP packet
->->->->->->->->->->->->->->->
R1 Local CSU/DSU | Remote CSU/DSU (remote loop given )
O-----------O------------------------------O |--------------------------------------O R2
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-|
View 5 Replies
View Related
May 8, 2013
We've had Cisco 1252 APs running on PoE (3750E gives the port 20W of power) for well over 3 years with no problems. These have not been touched, moved or configured since they went in.
All of sudden we're seeing these APs drop off the network and investigations reveal that they show as IEEE PD when you do a show power inline.
Some of these are slated to be replaced after the ports were changed, the cables replaced and port reset (also an old spare 1252 was inserted in to one of these ports and it came up fine, indicating an issue with these APs).
If it was one or two then maybe I could believe that the APs are at fault, but with so many (10 so far) I'm struggling to believe it. Could it be the code we are running on the switches? We are running 12.2(50)SE3.
View 6 Replies
View Related
