Is it possible to insert a Netgear wireless router b/g 108Mbs into a running 2008r2 network, making it a slave to allow wireless access?
At the moment the menu is only accessible thru 192.168.0.1, but I need to have it visible as a device subservient to 10.151.48.1? If this is possible, I can set it up to do a SSID broadcast for wireless access?
I'm living in a student flat, where each student has his own room.Every room has an LAN outlet in the wall on which he is able to connect 1 device.If you like to connect more devices, we are advised to utilize a router.Our ISP gives us the right to only use 1 MAC-adress (for safety reasons), so there the router comes into play.I have a Belkin G+ wireless router on which i would like to connect my phone and laptop by a wireless configuration and my TV (Toshiba 40TL933) by wire.My laptop and phone work like a charm.When i insert my TV to the network, the whole thing collapses.My ISP provided me with the information that i connected 2 MAC-adresses and therefore, i was cut off.This would be because of the fact that belkin routers (apparently) are notorious for providing more than 1 MAC adres.When i asked for the MAC-addresses, they gave me back these 2: * 00:00:00:00:00:00 * 00:17:3f:0d:77:f5The second one is from my Router.But where does the 00.00. etc come from?
View 5 Replies View RelatedI have the Netgear 4000 as primary router and I want to connect my second router WRT54GL running tomato firmware to my network.
View 2 Replies View RelatedI got a Cisco C880 router( IOS version: 15.1(2)T1 ) with PCEX-3G-HSPA-G card installed When I insert my 3G card and issue show cellular 0 network, I found that the network is not my 3G card ISP, may i ask how can I manual select the ISP?
View 1 Replies View RelatedMy motherboard ethernet port went bad, so I purchased a Netgear GA311 ethernet card. The issue is that Win7 wouldn't natively add driver support, though reviews indicated this card might be plug & play. Not so, and the driver disk even though it has 64 bit drivers will not run the install program at all. On top of that, the ethernet card does not appear in the Device Manager so I can backdoor the drivers into place.
View 8 Replies View RelatedIs NPS (windows 2008R2) supports EAP-TLS? I've built an NPS to authenticate wireless clients (WLC 2504). But in the EAP types I only see EAP(PEAP) this only requires a certificate on the server side.
I want the clients also should have a certificate, for that the NPS should support EAP-TLS
i wanted to know if i could setup a netgear wireless router to my ethernet cable that is coming out of the wall. is it as easy as plugging the cable coming out of the wall into the internet port on the router?
View 5 Replies View RelatedWe operate a home office network (workgroup) of 6 older PCs running Windows XP SP3.It's a Windows based network using a designated "home" PC as a server, and until recently we were using ethernet cables and a hub/switch for sharing files which worked well because we only share small document files, no music or video.The workgroup does not have a shared internet connection, we don't want or need one for what we do, although the individual PC's can connect to the web using USB dongles just for checking e-mail.Recently the ethernet hub died and I decided to take the opportunity to upgrade to wireless file sharing.None of the PCs have inbuilt wireless adapters so I bought a D-Link USB wireless adapter for each PC.I also bought a Netgear N300 router, thinking that this was suitable entry level equipment for wireless file sharing. Now I'm not so sure.So far I was unable to install the router on the "home" PC because the installation CD seems to assume that the router will be used for sharing an internet connection and does not seem to offer an installation option without a standalone modem. How to install this type of router to create a closed home wireless network without a shared internet connection.
View 14 Replies View RelatedBasically what is happening is I have a fiber decoder whitch goes into My belkin modem which controls my phone and Internet and with the company I am with we need that modem, I also have a netgear router so I can have wireless through my house but I want to plug LAN into the belkin router and still use the netgear for transmitting wireless.In short I want LAN in belkin but still have the netgear transmitting wireless and everything on the same network,E.g I have a pioneer amp and I use the iPhone app icontrol over my wireless but I can't because the amp is plugged into the belkin and the app is using netgear.
View 1 Replies View RelatedI have two netgear wireless modem / router. I want to connect my internet, NAS and Media player on one device (netgear modem/router) and want to link the other netgear in my bedroom and connect another media player and also use the internet via primary netgear modem/router wireless connectivity.
View 1 Replies View RelatedAdded a wireless router to our office here so that people with laptops could get on the net without having to physically plug in. Right now it is ok, but the router is acting as it's own DHCP server instead of our server here assigning out the IP's.
The main gripe I have is I can only login to the router through my phone and not through my computer. How can I achieve this. We have multiple offices that all connect through a VPN. I would like our sys admin to access the router at his location as well.
Do I just turn off DHCP on the router and thats it? The model is Netgear WNDR4500.
just bought a WD my book world edition 2 NAS and have been trying to tranfer files wirelessly to it but a 700mb file is taking 25mins to trans. my book is connected by ethernet to netgear dgnd3300 router and my laptop has sitecom 300n usb doongle.is there some sort of setting i've missed or is this speed normal?
View 5 Replies View RelatedI have a desktop and laptop and im on my desktop which has internet...I have a wireless router that is working and its called:NETGEAR WIRELESS-N 150 ROUTER WNR1000V2. The router network comes up on my laptop when I look for avaliable networks but..I try to connect and type in the exact password for the router but says "windows cannot connect to network" On my laptop im running windows vista home premuim service pack 2. This all starte 2 days ago when i knocked the outlet out that ha the power to our computer and i tuned it on and my laptop wont connect
View 5 Replies View RelatedCurrently using a netgear WG602 wireless router which i use to connect to my 2nd PC and Iphone, with the Netgear router running from my main PC.I have recently been having trouble with my 2nd PC ad Iphone randomly losing connection and the only way for the connection to be reastablished is to reboot the wireless router. Once rebooted i am able to connect again to the internet with no problems, interestingly enough my main PC never loses connection. Also sometimes when i lose my connection and reboot the wireless router i will have a IP conflict pop up on my 2nd PC however i would i say i get this once in every 10 dissconects and not all the time. Sometimes i won't dissconect at all in a day but sometimes i may dissconect 5-6 times.
View 1 Replies View RelatedI'm using a wireless router which will not browse unless i disable LAN. How can I have the LAN connected and Wi-fi router connected at the same time?
View 3 Replies View RelatedI have a Netgear WNR612 wireless router, which worked fine for a few weeks. Then something happened and I can't keep the connection anymore. It happened right after I used iTunes to update my iPhone, perhaps a coincidence, but I'm mentioning that just in case. Internet still works fine with ethernet cable straight from the computer, only the wireless connection doesn't work. This happened about a month ago and I haven't been at home much to fix the problem. I have turned off and unplugged everything for several days at a time while gone. I get a Network Error message saying, Windows has detected an IP address conflict. I have tried restoring the router back to factory settings and reinstalling the wireless card. I have tried changing the IP address settings both in the Network and Sharing Center and the router admin page. What I think I should do is change the IP address in Command Prompt, but when I type "ipconfig /release", it says "No operation can be performed on Wireless Network Connection 2 while it has its media disconnected" and the same for Local Area Connection. I don't understand what this means, because there is a wireless key in my keyboard and there is a white light (not orange) like there should be. Also in the Network and Sharing Center, I can see that the connections are enabled.
View 14 Replies View RelatedI have a problem with configuring of my vwic3-2mft-t1/e1 card on Cisco 2821 router. I need drop some raw data timeslots from E1 frame and then insert them into frame on other port. I enter the following commands:
card type e1 0 0
controller e1 0/0/0
tdm-group 0 timeslots 1-4
clock source line
controller e1 0/0/1
tdm-group 2 timeslots 1-4
[code]....
I find these commands in Cisco 1 and 2-port T1/E1 Multiflex Voice/WAN Interface Cards for the Cisco 1700 Series Router configuration guide for vwic2 cards.But this config is not working properly. show connect output is showing status of connection "UP", show controller e1 shows no errors on both e1 ports, but data not flows between ports.What am I doing wrong? Have vwic3 and vwic2 cards different configuration procedures or not?
I have a working configuration with a 2811 router at my remote site in which I take the T1 (point-to-point PRI) into port 0/0/0 on the dual-port vwic2-mft-t1/e1 card. Then I plug my PBX into the 0/0/1 port. I channelize the T1 so 1/2 of the channels are used for data (13-24) and channels 1-8 are passed through the vwic2 to the PBX. I'm using the connect tdm t1 0/0/0 0 t1 0/0/1 0 command to pass the voice calls through to the PBX.
I tried to upgrade the router to a 2911 with the same card and the same configuration copied and pasted over and as soon as I put the connect tdm t1 0/0/0 0 t1 0/0/1 0 statement in, I drop the data side of the T1 and lose my connection to the WAN. If I take the command back out, the WAN still doesn't come back up until I reboot the router.
Has the syntax changed? I have a case open with TAC but so far no luck, as they can't seem to figure out which group should take this case, voice or data..
We are using an ACE engine module(ACE20-MOD-K9) provide loading balancing service for two WEB servers and configured cookie for stickness. Below is the current configuration and it seems working fine now.
The problem I was facing is before use parameter-map change the http header length to 8k the stickness doesn't really working properly. User complains that their working session constantly be kicked out and redirect them to login page. By tracing traffic from a client we found that sometime ACE fails or stop insert the configured cookie, after increase the header length ACE start getting work.
how does the header length setup effect ACE to insert a cookie? Will the cookie insert attmpt fail if the header is longer then the maximum length configured on ACE? [code]
I have an ACE version A5.2 configured in one-armed leg (doing source nat). I have a requirement to add(or copy) the "referer" header value from the original request to the request send by ACE.
I cannot figure out how to copy this value. It is easy to add the source ip address by adding: " insert-http x-forwarded-for header-value "%is".
So how I am going to copy the Refere header?
#Referer
#Address (URI) of the resource from which the URI in the request was obtained
We are using Cisco ACE 4710 to load balance servers. We have created VIP under the interface vlan using nat-pool command. Also, we have changed the gateway of the server to point to the ACE vlan ip address which is created using alias 10.x.x.x 255.x.x.x command under the interface vlan. In short ACE is in inline mode for the servers which needs to be load balanced.
[code]...
But still I am not able to view the original client IP. Just to add more, the site is a HTTPS site & we have not doing any kind of SSL offloading on the ACE, it is taken care by server itself
I just want to do the HTTP & HTTPS load balancing without SSL offloading & should be able to see the original client IP in the server logs
I've come across an older IBM ThinkPad 2687 via work that was just collecting dust, and it was able to connect to a wireless network.Due to other issues with the machine, I had to do a complete refresh on it, so it only had the XP OS.
I had to update the drivers to make sure other things like connecting to a flash drive, and connecting to a local area was possible, which is how I'm able to connect now.However, I've been unable to access the wireless connection within Network connections. I've downloaded the different drivers from the Lenovo IBM ThinkPad website, but still no luck.
I was online then all of a sudden i got disconnected and now it won't show any network available. My other laptop and xboxes are online just fine, so I know then it's an issue with my one laptop. But I don't know how to fix it. No networks are found at all and internet only works when it's wired. I have a HP laptop running windows 7.How do I get my network to show up so I can have wirless internet again? Someone thought maybe new drivers but no clue what I really need to download. I only know basics of computer stuff.
View 1 Replies View RelatedHaving performance issues running two 5508 controllers on the same network? One is running 7.3.101.0, the other is running 7.0.98.0. The legacy APs are connected to the WLC on the older code to support older hardware. The new WLC is accepting all the new 3600 APs. Once all legacy APs are replaced, the 5508 on old code will be disabled.
View 3 Replies View RelatedI am wanting to setup a small network at home. I am using Server 2008r2 64 bit running on VMWorkstation, which is the only way I can run a 64bit OS. I have it installed and running on VM with active directory and a domain created. My problem is trying to join the domain with my other PC's. They cannot find the domain name. The network connection on the VM is set to NAT.
View 2 Replies View Relatedwhile the 3560 switch is running? Is it hot-pluggable?
WS-C3560X-48P is the switch and I would be adding a C3KX-PWR-1100WAC
I am moving a Windows Server to a new location. We currently have static IPs but are not using any of them so at the new location I requested no new static IPs. With that being said is there anything I need to worry about when I move? From what I have heard it should be a turn it on and go type of move.
View 1 Replies View RelatedDHCP = win2008r2
scope 1:
172.16.1.51 - 172.16.1.200
sub net 255.255.255.0
router: 172.16.1.1
scope 2
172.16.3.51 - 172.16.3.200
Sub net 255.255.255.0
router: 172.16.3.1
Nic1 = 172.16.1.20
Nic2 = 172.16.3.20
[Code] ......
After completing an AD upgrade to 2008r2 I've had my fill of roaming profiles. I want to change all users back so that their profile is on their pc. Of course ideally I'd like this to occur with the user affected as little as possible. Most users are still winxp but some win7 machines too.
View 18 Replies View Relatedi was wondering if i really NEED to install the certificate services role in 2008r2,what do i lose by not having it, and what do i gain by using it ?
View 5 Replies View Relatedhow to use Microsoft server 2008R2 NPS with cisco wlc 4400.am i correct, each LWAPP AP have to be connected to NPS . (this AP is also called access server)?when client tries to connect to the wlan, (in this case lets say we want a user in AD, after providing its creds, can access the network, internet etc) the auth req is sent from AP to NPS/RADIUS? where does WLC come into play here, what does WLC do?
View 3 Replies View Relatedi have a netgear router,and i cannot connect new laptops bec it requires password how to connect or know d password
View 1 Replies View RelatedWe had a power outage that kicked off our server and our network switch (2008R2, Cisco2960), before we could get it back up, a user was able to log into his laptop.
The user used the domain login - not the local machine account - he obviously wasn't able to access any shared resources, but how did he log in with a domain account, when the server and switch were both off?