I'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.
[URL]
I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies View RelatedI'm going to be swapping out a WIC-1DSU-T1-V2 for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
configuration examples for the two T-1 setup ?
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?
Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 1 Replies View RelatedI think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
Router 1-----
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
(code)
I have been advised by my service provider that to do ATM IMA I need an AIM-ATM and a VWIC2-2MFT-T1/E1 card, and that IMA is not support on the VWCI2-2MFT-G703 card.
View 5 Replies View Relatedi have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
View 9 Replies View Relatedthe VWIC2-2MFT-T1/E1 hardware installation guide?
View 1 Replies View RelatedI have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
I have a VWIC2 running two T1 circuits to two locations. Can I put the controllers on the same channel group? I also have a PPP multilink controller on a VWIC2 on channel group 0.
View 2 Replies View RelatedI have checked and re-checked before buying and this card is evidently supported on the 1841 for 'data mode only' which is all I need. I have 3 T1s in Multilink mode and I want to use 2 of these cards (and 3 of the 4 ports) to support it. The problem is that even though SH INVENTORY finds the card, I can't issue the "card type" command to indicate I am using it with a T1 - I get this:
R3(config)#card type t1 1 0
^
% Invalid input detected at '^' marker.
So I tried to issue the "controller T1" command and it does not recognize the slot as containing a T1 card (which makes sense since the "card" command did not work).
I found numerous references to this card being supported in Cisco docs with a minimum OS around 12.2(8) - it varies based on the chassis. I can't find the explicit OS required for the 1841 which is a concern but I am using 12.4(13r)T. SH VERSION finds "2 Channelized T1/PRI ports" which is the MFT card.
I need to get Serial interfaces configured on these cards.
I have a problem with configuring of my vwic3-2mft-t1/e1 card on Cisco 2821 router. I need drop some raw data timeslots from E1 frame and then insert them into frame on other port. I enter the following commands:
card type e1 0 0
controller e1 0/0/0
tdm-group 0 timeslots 1-4
clock source line
controller e1 0/0/1
tdm-group 2 timeslots 1-4
[code]....
I find these commands in Cisco 1 and 2-port T1/E1 Multiflex Voice/WAN Interface Cards for the Cisco 1700 Series Router configuration guide for vwic2 cards.But this config is not working properly. show connect output is showing status of connection "UP", show controller e1 shows no errors on both e1 ports, but data not flows between ports.What am I doing wrong? Have vwic3 and vwic2 cards different configuration procedures or not?
I had to dig this stuff out of storage and cobble together a router on short notice. I installed this WIC into a 2821 and I can see it when I do a show ver.
Cisco 2821 (revision 53.51) with 249856K/12288K bytes of memory.Processor board ID FTX1006C0P32 Gigabit Ethernet interfaces2 Channelized T1/PRI ports <-----------------------------1 Virtual Private Network (VPN) ModuleDRAM configuration is 64 bits wide with parity enabled.239K bytes of non-volatile configuration memory.125440K bytes of ATA CompactFlash (Read/Write)
When I do a sho run I see this:
controller T1 0/0/0 framing esf linecode b8zs!controller T1 0/0/1 framing esf linecode b8zs
How do I configure IP interfaces on it though? It doesn't seem to show up as Serial ports on a sho int. Am I doing something wrong?
I was just given a task to setup some T1 connections. We rarely use T1 interfaces anymore as they are typically just not enough anymore. I see the newer vwic3 interfaces are supported on various 2900 series but downloaded the vwic3 configuration guide and noticed that the 1900 series routers were not in the list? Is this correct. So are vwic3-2mft-t1 ehwic cards supported or not on 1921 routers? i can see the controller interfaces but not the ports as there must be additional configuration required. Im running 15.1(4)M4 IOS version that looks to be supporting the cards.
View 2 Replies View RelatedI have a 2921 router, with UCK9 services on it. I've installed a VWIC2-2MFT but the system is not seeing it. I've been told there is a command required to enable the card, is this true? I've always done most of my UC work on the 2800 range and never had to run an enable command, it just saw the card.
View 5 Replies View RelatedI have a 2811 that I'm in the process of turning-up to support a 4xT1 using VWIC-2MFT-T1's. The question is how to "correctly" set clocking on the MFT's.
As is typical of the 2MFT's, as soon as a 2nd T-1 on a VWIC-2MFT comes up, I start taking "Slip Sec"s on the 2nd T-1. I have tried different clock source combinations, including "clock source line primary", various "network-clock-participate" (or not) combinations, and about a dozen other stab-in-the-dark configurations. Before I started playing with it, the slips were consistently every 9 seconds. After playing with it, I got them to every 18 seconds. But there shouldn't be ANY. So the question is what SHOULD the correct timing configuration be on that platform?
The VWIC-2MFT-T1's are in slots 1 and 3, so the controllers involved are 0/1/0, 0/1/1, 0/3/0 and 0/3/1.
Can I use module vwic2-1mft-g703 for ISDN PRI?
View 1 Replies View RelatedI am trying to install VWIC2-1MFT-T1/E1 into c2600 router w IOS C2600 Software (C2600-I-M), Version 12.3(26) with 28672K/4096K bytes of memory It is not recognized? Do I need another version of IOS?
View 2 Replies View RelatedI have not worked on the new VWIC cards lately. I would like to know how I can configure the serial IP address like we used to do in the older T1 DSU WIC cards. I do not see any interface that shows as serial. I have configured the controller as a T1 controller but still no luck.
View 1 Replies View RelatedTrying to connect two Cisco 1941 routers with VWIC2 1MFT-T1 interfaces on point-to-point T1 (No Voice). Sample configuration, this is what I have so far, but I'm not sure if it's correct. Do I need any specific information from my point to point T1 provider?
ROUTER A
controller T1 0/0/0
cablelength long 0db
[Code].....
I am trying to use the connected WIC2-2MFT, as the servial interface on my cisco 1841.But it does not show me the option, under configuration interface
[code] What should I do to make this enable on this list?I am attaching the show tech-support, and show version of this device.
We have installed a VWIC-2MFT-T1 interface card into our 1841 router and the interface doesn't show up in CP. # we only need it for data. #
ROM version 12.4(13r)T, RELEASE SOFTWARE
All indications from my research show that this version should support this card, for data only.
why I can't see this card when I show interfaces?
I have installed a VWIC2-1MFT-G703 module into cisco 2921 router, I can verify the card by show inventory command. but in show run, I do not see the E1 controller card there. this card is used for TPG lease line for data only. Those card is compatible with new 2921 router? or need some extra command to bring it up?
View 2 Replies View RelatedWe have a cisco 3825 router with OS version 12.4 and one VWIC2-2MFT-T1/E1 card at Slot 0. Now I have to add one more card of the same type in the router.
I need to know the steps or process to add the the 2nd card in the router.
We have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
[Code]....
How maximum channel-group supported by VWIC2 1MFT G.703? And the CISCO1941/K9 ?
View 0 Replies View RelatedVWIC2-1MFT-T1/E1 card support on 1841 Router ?any ios up-gradation required?
View 1 Replies View Relatedour customer has a server farm in a data center.At the moment the farm has connectivity with only one ISP but sometimes it has service discontinuity.Customer wants to become AS and having two ISP connectivity for backup purposes.He needs to evaluete two cisco routers to use at AS edge with BGP.At the moment he says that the throughputh with the server farm is max 15Mbps and in the future he thinks that it will not increase.We think about cisco2951 routers with 2GB ram.Is cisco 2951 adeguate for this task ?
View 3 Replies View RelatedI have the situation with my new Cisco 2951 router. It has only one module on board - SM-D-ES3-48-P. I don't know what is wrong but I can't see any information about this module. When I connect my laptop to any port it's become green, but it's still green even after I disconnect PC from this port. Sh ip int brief command shows only built-in gigabit interfaces. I also connect my second PC to the router by console to monitor any changes when I connect or disconnect laptop to the module's ports. [code]
View 3 Replies View RelatedI'm setting up IPsec for a DMVPN between a 2811 and 2951s in a test lab. I have enabled IPsec on the hub (2811) but I am unable to do so on either of the 2951s. After researching, it seems that I may have the incorrect IOS for this, but I am at a loss which IOS I should be using. Currently the 2951s are on "c2951-universalk9-mz.SPA.151-2.T2.bin".
View 1 Replies View RelatedWe have an old 3725 router with a HSSI card connected to a DL3100, which in turn is connected to a subrate DS3 circuit. The plan is to replace the router with a new 2951 router and a NM-T3/E3 card.After the router was replaced, I configured the NM but the circuit remained dow/down. I'm sure it has to do with the fact that the DS3 circuit is channelized but I'm not sure how to configure this module to be channalized. Here is the configuration that I placed on the router: [code]
View 4 Replies View RelatedWe recently purchased the Cisco Router 2951 router with the IOS 15.0. I have tried to put in my VIC2-4FXO card in it. When I did show invetery, it detected the card.[code] When I tried to configure the voice port by typing voice port, it shows % Invalid input detected at '^' marker. I have tried to reset the cad and replace with another one.
View 3 Replies View Relatedsetting up IPsec for a DMVPN between a 2811 and 2951s in a test lab. I have enabled IPsec on the hub (2811) but I am unable to do so on either of the 2951s. After researching, it seems that I may have the incorrect IOS for this, but I am at a loss which IOS I should be using. Currently the 2951s are on "c2951-universalk9-mz.SPA.151-2.T2.bin" and the only crypto options.
View 9 Replies View Related