I was just given a task to setup some T1 connections. We rarely use T1 interfaces anymore as they are typically just not enough anymore. I see the newer vwic3 interfaces are supported on various 2900 series but downloaded the vwic3 configuration guide and noticed that the 1900 series routers were not in the list? Is this correct. So are vwic3-2mft-t1 ehwic cards supported or not on 1921 routers? i can see the controller interfaces but not the ports as there must be additional configuration required. Im running 15.1(4)M4 IOS version that looks to be supporting the cards.
I have a problem with configuring of my vwic3-2mft-t1/e1 card on Cisco 2821 router. I need drop some raw data timeslots from E1 frame and then insert them into frame on other port. I enter the following commands:
I find these commands in Cisco 1 and 2-port T1/E1 Multiflex Voice/WAN Interface Cards for the Cisco 1700 Series Router configuration guide for vwic2 cards.But this config is not working properly. show connect output is showing status of connection "UP", show controller e1 shows no errors on both e1 ports, but data not flows between ports.What am I doing wrong? Have vwic3 and vwic2 cards different configuration procedures or not?
We have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version ============ System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin" Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability delay down 1 up 1 ! track 20 rtr 2 reachability delay down 1 up 1 ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
I have been advised by my service provider that to do ATM IMA I need an AIM-ATM and a VWIC2-2MFT-T1/E1 card, and that IMA is not support on the VWCI2-2MFT-G703 card.
I have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
I am trying to setup my new 2901 running 15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card. Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s. None of the commands I am used to seem to even exist. None of the
Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.
Can I populate all 4 EHWIC slots in a Cisco 2911 router with VWIC3-4MFT-T1/E1 cards supporting clear channel T1 data traffic?Or do I need a higher performance router inthe 3900 series to do this?The data sheets lead me to the conclusion that I can but I just want to validate this.
I have checked and re-checked before buying and this card is evidently supported on the 1841 for 'data mode only' which is all I need. I have 3 T1s in Multilink mode and I want to use 2 of these cards (and 3 of the 4 ports) to support it. The problem is that even though SH INVENTORY finds the card, I can't issue the "card type" command to indicate I am using it with a T1 - I get this:
R3(config)#card type t1 1 0 ^ % Invalid input detected at '^' marker.
So I tried to issue the "controller T1" command and it does not recognize the slot as containing a T1 card (which makes sense since the "card" command did not work).
I found numerous references to this card being supported in Cisco docs with a minimum OS around 12.2(8) - it varies based on the chassis. I can't find the explicit OS required for the 1841 which is a concern but I am using 12.4(13r)T. SH VERSION finds "2 Channelized T1/PRI ports" which is the MFT card.
I need to get Serial interfaces configured on these cards.
Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
I think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
I'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.
I had to dig this stuff out of storage and cobble together a router on short notice. I installed this WIC into a 2821 and I can see it when I do a show ver.
Cisco 2821 (revision 53.51) with 249856K/12288K bytes of memory.Processor board ID FTX1006C0P32 Gigabit Ethernet interfaces2 Channelized T1/PRI ports <-----------------------------1 Virtual Private Network (VPN) ModuleDRAM configuration is 64 bits wide with parity enabled.239K bytes of non-volatile configuration memory.125440K bytes of ATA CompactFlash (Read/Write)
When I do a sho run I see this: controller T1 0/0/0 framing esf linecode b8zs!controller T1 0/0/1 framing esf linecode b8zs
How do I configure IP interfaces on it though? It doesn't seem to show up as Serial ports on a sho int. Am I doing something wrong?
i have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
I have a 2811 that I'm in the process of turning-up to support a 4xT1 using VWIC-2MFT-T1's. The question is how to "correctly" set clocking on the MFT's.
As is typical of the 2MFT's, as soon as a 2nd T-1 on a VWIC-2MFT comes up, I start taking "Slip Sec"s on the 2nd T-1. I have tried different clock source combinations, including "clock source line primary", various "network-clock-participate" (or not) combinations, and about a dozen other stab-in-the-dark configurations. Before I started playing with it, the slips were consistently every 9 seconds. After playing with it, I got them to every 18 seconds. But there shouldn't be ANY. So the question is what SHOULD the correct timing configuration be on that platform?
The VWIC-2MFT-T1's are in slots 1 and 3, so the controllers involved are 0/1/0, 0/1/1, 0/3/0 and 0/3/1.
I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
I am trying to use the connected WIC2-2MFT, as the servial interface on my cisco 1841.But it does not show me the option, under configuration interface
[code] What should I do to make this enable on this list?I am attaching the show tech-support, and show version of this device.
We are a small business that just bought a Cisco 1921 ISR. I am trying to set it up right now but I cannot get CCP to discover it. I am new to Cisco products and IOS.The router is currently set up in a test environment with a USB connection to a Win7 PC for console management. I also have the PC connected to gigabit ethernet port 0/1. I am using putty to access the console which I did with no problem for the initial configuration. After that I thought I would be okay to discover the router with CCP using the IP address I specified but then it prompted me for a username/password which I didn't see in the initial configuration. After this I did some research and found out I needed to set up a few more things so I ran the following commands: [code]
After this the video I was watching said to go in to CCP and specify the IP address or hostname of the router and use the login info that was just created admin/pw. When I ran the discovery I got the failure message: Connection to the device could not be established. Either the device is not eachable or the HTTP service is not enabled.When I run 'show ip interface' I notice 'Router Discovery disabled" is this why it is not working? How can I enable this or what else am I missing here? Am I not connecting to the router correctly? Oh and just for reference our plan is to have this router set up as a VPN gateway and firewall with 2 WANs for redundancy and connecting to our switch via an HWIC SFP for fiber.
I have installed a Cisco 1921 router in our company and i have stumbled upon an issue with the DNS.
We have a internal DNS server and an internal WEB server. In the DNS server there are records pointing to sites on the WEB server, this is working just fine.
The thing is when i use a public DNS such as 8.8.8.8 (googles public DNS) i cannot resolv the external IP of those sites. I do not want to access the sites and i do not want to send any packets to the sites. All i want is to query the public DNS and resolv the public IP where the site is.
I have been playing around with a 1921/K9 router in our dev environment. It's been about 24 hours and I just can't seem to get it to work. My DHCP Server is working hence my internal network is getting IP address as desired. But Router doesn't seem to connect to internet for some reason.
I am trying to make it a internet facing router with static IP address (67.210.209.113). LAN side of this router will be our .11 Network which is our Dev Network.
Here is some network information:
WAN: Interface IP: 67.210.111.111 Default Gateway: 67.210.111.222 (I can ping this address through router) tlm1921A-11A#ping 67.210.111.222
Any issues upgrading the IOS on a 921 router.How can i create a certificate for the new IOS? I've never had to do this for other IOS 15 upgrade?I've confirmed the IOS is not corrupt and if i upgrade the router in ROMMON the router boots correctly.
I have purchased a PAK for my 2 cisco 1921 routers .I would like to to configure IP SEC or SSL for VPN connectivity on the routers. How do i convert the PAK into a license?
I am really stuck with router requirement for one of our client. I need 891 SEC router. I think this comes with advanced IP services. What I have is 1921, with IP Base. can I upgrade 1921, so it will become alternative to 891 SEC.
I'm attempting to set up a Cisco 1921 router running IOS15, and am having trouble with the NAT - it might be that what I am attempting is not possible. The only traffic going across the router is UDP, and the outside of the network canot be changed.
