Cisco VPN :: 1921 - Converting PAK Into A License
Sep 6, 2011I have purchased a PAK for my 2 cisco 1921 routers .I would like to to configure IP SEC or SSL for VPN connectivity on the routers. How do i convert the PAK into a license?
View 1 Replies
ADVERTISEMENT
Cisco WAN :: Install License On 1921 With USB
May 12, 2013how install a .lic file onto the new Cisco ISR G2 1921?
I know how to install via tftp, however I need to know how to install from USB.
Cisco WAN :: 1921 License Is Showing Active But Not In Use
Apr 16, 2011i purchased 1921 with ipbase license , then i installed security 60 days trial license in it.the license is showing active but not in use and in the sh version also is not showing.then i used some command like boot using security bundle then i restarted the router , after that i am getting the following the message "loadprog bad file magic number 0x0 boot cannot load flash".then i tried to upload from tftpdnld using rommon mode then i am getting following error "Interface GE 0 link down TFTP: Operation terminated prematurely in rommon mode".
View 2 Replies View RelatedCisco WAN :: 1921 - IOS Upgrade With Security License?
Nov 4, 2011I have a Cisco 1921 ISR Router with Security License running software version 15.0. I want to upgrade the router to 15.1. But I don't want to lose the security license that came with the router. When I look at the IOS downloads page on Cisco, all I see is universal images for all versions of 15.1.
My question is - where is the security license stored? In the IOS or programmed in somewhere else of the router? If I upgrade my router to one of the newer 15.1 universal images, will I lose my security license?
Cisco WAN :: After Installing Data License In 1921 Router It Does Not Show?
Dec 13, 2011 i installed Data license(Evalutation) initally it took the license after reload, when i enter sh lic command the out put shows that Data license is installed and valid for...
But when i run sh ver command it only shws ipbase license and not the data license
Cisco WAN :: 1921 - Special License To Utilize Balancer / Failover Feature?
Apr 21, 2013Lately we have been comsidering an upgrade in our organization involving a 1921 router. The main role it will play is a load balancer/failover between 2 connections from 2 different ISPs. what additions are required to be added to this piece of equipment to make the configuration work. Im researching the matter now and it seems an extra card whould be purchased in addition to the router. Also, i cant seem to find much information on the available licenses to go with the router. will i need a special license to utilize the balancer/failover feature? (ip base, data, SEC).
View 2 Replies View RelatedCisco Switching/Routing :: IP SLA Support On 1921/K9 Or 1921-SEC/K9?
Oct 5, 2012We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
Cisco Firewall :: Difference Of VPN Plus License And Security Plus License ASA 5520
Oct 16, 2012What's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedCisco :: Installation PI1.2 Basic License With LMS4.0 License For 100 Devices
Apr 3, 2013I’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
Cisco Wireless :: 1240AG Converting From WEP To WPA
Aug 20, 2012Cisco 1240AG converting to WEP to WPA
Access Point Model: Cisco 1240AG
System Software Filename: c1240-k9w7-tar.123-7.JA5
System Software Version: 12.3(7)JA5
Bootloader Version: 12.3(7)JA1
Access Point Model: Cisco 1131AG
Software: Cisco Aironet Desktop Utility 2.1.02
After converting encryption from WEP to WPA in a Cisco 1240AG in personal mode with an SSID name of example1 and Cisco 1131AG access point in personal mode with an ssid of example2; both with the same wpa passphrase, I created a new profile on the Cisco Aironet Desktop Utility with a new profile name as well as a WPA passphrase, but the desktop utility will only connect to the access point if one network name, example1 or example2, is entered.
Cisco WAN :: ASA5505 Converting Private To Public IP For VPN
Aug 18, 2011We have a VPN router(ASA5505) which connects to the client, B. IP address for one si 195.xx.xx.xx and for B it is 14.xx.xx.xx. Both can extablish a IPSEC VPN nicely.Now, B throws a condition that the IP coming thru the VPN has to be PUblic. They want it as such so that they can be routed across the VPN tunnel.It still can because the firewall does not do NAT.
View 5 Replies View RelatedCisco Wireless :: Converting 1242ag To And From LWAPP
Apr 5, 2013is this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedCisco Wireless :: Converting AIR-AP1131AG-E-K9 Into Standalone AP?
Jul 5, 2011I have a Brand new AP that was bought for a site which has a controller, however it was never installed. I was wondering can you downgrade this AP to make it work in stand alone mode as a normal AP?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Converting 3140 CAM To CAS Server
Feb 7, 2011How to convert a 3140 CAM to a CAS ? if so what software / licensing would be required and is there a documented process
View 1 Replies View RelatedCisco Wireless :: Converting 3600 To Autonomous?
Jan 13, 2013I am not having much luck getting it converted via normal ways.
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing).
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar 1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..' Even if I set a static IP address.
Is there way to disable the join process while I upgrade the software? I guess fire up a controller for it to join. I hope I don't have to have a controller to convert these.
Cisco Wireless :: Converting AIRLAP1142 To Autonomous
May 17, 2012I have an AIR-LAP1142 that I'm trying to load the autonomous software onto. I reset the AP with the mode button held down as per instructions. When I release, it attempts to download c1140-k9w7-tar.default from my pc running tftpd62. Several connections are made and then it eventually times out. I tried another machine (also win7 x64) and it fails there too exactly the same.
TFTP logs show:
Connection received from 10.0.0.1 on port 1024 [18/05 17:22:04.269]
Read request for file <c1140-k9w7-tar.default>. Mode octet [18/05 17:22:04.270]
Using local port 51686 [18/05 17:22:04.270]
[Code].....
Wireless :: Converting EXE File To SIS Format?
Jun 22, 2011How can I convert exe file to sis format.
View 1 Replies View RelatedConverting Router To Access Point
Mar 22, 2012I am having problem converting my router echolife HG532b to work as an access point. I have main router as linksys wag 120 with IP adress 192.168.1.1 and DHCP server enabled and IP range from 192.168.1.2 to 192.168.1.100 . I changed the IP adress of the echolife to IP adress withen the range of DHCP and disabled the DHCP server according to this thread Connecting Additional Routers, I changed the wireless setting to match main router with secondary router and connected Cable from main router to LAN port of echolife. When i tried to connect wireless to the network. It takes 5-15 second obtaining the IP adress then it connects but with limited connection with no internet. I have noticed that when i just plug the cable to echolife it become online in the network map for 10-30 sec then it goes offline. I tried to choose IP adress for echolife outside the range of DHCP. In network map echolife stays online but still same problem limited connecting and no internet
View 6 Replies View RelatedCisco Wireless :: Converting 2602 From Lightweight To Autonomous?
Feb 19, 2013I have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
Cisco Wireless :: Converting 1040N Autonomous AP To LWAPP
Oct 5, 2011I have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies View RelatedCisco Infrastructure :: Converting WS-C3560G Switch To DC Power?
Apr 15, 2013What needs to be done to convert a WS-C3560G-24TS-E to DC power?
View 2 Replies View RelatedCisco Wireless :: Converting AIR-SAP2602i-s-k9 From Autonomous To LWAPP
Feb 26, 2013I need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
Cisco Firewall :: Converting To ASA5520 Rules Base
May 17, 2012I am just about to start on a project where we are moving from Old Cyberguard firewalls to ASA 5520 firewalls, any rule base converstion tool that would be able to do a lot of the basic work? And so of the NAT conversions?
View 1 Replies View RelatedCabling / Cards :: Converting RJ45 To USB Port?
Dec 14, 2011I have an old 2007 model Toshiba HD LCD television. It does not have a USB port, but it does have a connection for RJ45. I want to convert this to a USB port, Is there a converter/connector for this purpose?
View 3 Replies View RelatedConverting Wireless Signal To Wired With Computer?
Jan 18, 2011My desktop computer doesn't have a wireless card in it. i also have a laptop which does have a wireless card. I was wondering if there is a way i can take the wireless connection and re-transmit it to the desktop through ethernet. I have a 5-port switch. I don't really know much about networking. but i am knowledgeable in computers. laptop has windows 7 on it. i really would prefer to not buy a wireless card for the desktop.
View 2 Replies View RelatedConverting Netgear Wndr370 To An Access Point?
Apr 18, 2012I have an AT&T 2Wire Router/Modem and want to convert my Netgear WNDR370 to an Access Point.
View 1 Replies View RelatedCisco Wireless :: Converting 881W From LWAPP To Autonomous Mode
Aug 19, 2010I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
TP-Link ADSL2+ Wireless :: TD-W8951ND / Converting LAN To WAN Port?
Jan 1, 2013Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : 5.0.0
ISP : Beam Telecom
I recently bought this device in hurry . My ISP has directly connected RJ45 cable to my laptop .So i need to use this device for sharing internet to my wireless devices .IS it possible to convert Rj45 to Rj11 if so let me know the process .I have seen interenet about converting lan port to wan for TD-W8960 device . but GUI administration is quite different for my device .
Cisco Wireless :: Converting A 1260AP From Autonomous To Light Weight Mode
Jan 17, 2013Is the process for converting 1260 APs to lightweight mode any different from converting 1140s or 1250s? I've converted several APs to LWAP mode but this is my first 1260. Four 1260s need to be converted.I have one in a remote location that seems to be comatose. Here are the steps I took to convert the AP. Did skip/miss a step?
1. uploaded code to the AP ap3g1-rcvk9w8-tar.152-2.JB.tar
2. configured the AP for DHCP. It successfully leased a DHCP address. Controller information is provided via DHCP Option 43.
3. saved the configuration
4. verified the code, successful
5. disabled wireless radios
6. installed the lightweight code using the command archive download-sw /safe flash:/ap3g1-rcvk9w8-tar.152-2.JB.tar.The installation was successful
7. rebooted the AP
After that nothing. The AP has not leased another IP address. The switchport is active. The APs MAC address is registering in the switches MAC address table. The AP is receiveing PoE from the switch. I noticed that this AP is only receiving 6.2W of power where the three are getting anywhere between 8.8W and 9.3W. I am unable to ping the old static IP of the AP too.
Cisco Switching/Routing :: Configuration Differences When Converting From ME3750 To ME3800x
Sep 29, 2011system mtu routing 1500 Is there a replacement command for this?
MLS QOS commands not accepted. Has the ME3800 been designed so these buffers don't need to be adjusted?
in the policy map:
class class-default
random-detect dscp-based not accepted. Is there a work around?
[Code].....
Cisco WAN :: 1921 Cannot Get CCP To Discover
Oct 27, 2011We are a small business that just bought a Cisco 1921 ISR. I am trying to set it up right now but I cannot get CCP to discover it. I am new to Cisco products and IOS.The router is currently set up in a test environment with a USB connection to a Win7 PC for console management. I also have the PC connected to gigabit ethernet port 0/1. I am using putty to access the console which I did with no problem for the initial configuration. After that I thought I would be okay to discover the router with CCP using the IP address I specified but then it prompted me for a username/password which I didn't see in the initial configuration. After this I did some research and found out I needed to set up a few more things so I ran the following commands: [code]
After this the video I was watching said to go in to CCP and specify the IP address or hostname of the router and use the login info that was just created admin/pw. When I ran the discovery I got the failure message: Connection to the device could not be established. Either the device is not eachable or the HTTP service is not enabled.When I run 'show ip interface' I notice 'Router Discovery disabled" is this why it is not working? How can I enable this or what else am I missing here? Am I not connecting to the router correctly? Oh and just for reference our plan is to have this router set up as a VPN gateway and firewall with 2 WANs for redundancy and connecting to our switch via an HWIC SFP for fiber.
Cisco WAN :: DNS Regarding A 1921 Router
May 18, 2011I have installed a Cisco 1921 router in our company and i have stumbled upon an issue with the DNS.
We have a internal DNS server and an internal WEB server. In the DNS server there are records pointing to sites on the WEB server, this is working just fine.
The thing is when i use a public DNS such as 8.8.8.8 (googles public DNS) i cannot resolv the external IP of those sites. I do not want to access the sites and i do not want to send any packets to the sites. All i want is to query the public DNS and resolv the public IP where the site is.
Cisco :: Where To Find Ios For Free 1921-SEC / K9
Jul 3, 2012where can i find this ios for free CISCO1921-SEC/K9 ?
View 4 Replies View Related