Cisco Wireless :: Converting 3600 To Autonomous?
Jan 13, 2013
I am not having much luck getting it converted via normal ways.
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing).
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar 1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..' Even if I set a static IP address.
Is there way to disable the join process while I upgrade the software? I guess fire up a controller for it to join. I hope I don't have to have a controller to convert these.
View 31 Replies
ADVERTISEMENT
May 17, 2012
I have an AIR-LAP1142 that I'm trying to load the autonomous software onto. I reset the AP with the mode button held down as per instructions. When I release, it attempts to download c1140-k9w7-tar.default from my pc running tftpd62. Several connections are made and then it eventually times out. I tried another machine (also win7 x64) and it fails there too exactly the same.
TFTP logs show:
Connection received from 10.0.0.1 on port 1024 [18/05 17:22:04.269]
Read request for file <c1140-k9w7-tar.default>. Mode octet [18/05 17:22:04.270]
Using local port 51686 [18/05 17:22:04.270]
[Code].....
View 3 Replies
View Related
Feb 19, 2013
I have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
View 28 Replies
View Related
Oct 5, 2011
I have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies
View Related
Feb 26, 2013
I need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
View 2 Replies
View Related
Aug 19, 2010
I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
View 4 Replies
View Related
Jan 17, 2013
Is the process for converting 1260 APs to lightweight mode any different from converting 1140s or 1250s? I've converted several APs to LWAP mode but this is my first 1260. Four 1260s need to be converted.I have one in a remote location that seems to be comatose. Here are the steps I took to convert the AP. Did skip/miss a step?
1. uploaded code to the AP ap3g1-rcvk9w8-tar.152-2.JB.tar
2. configured the AP for DHCP. It successfully leased a DHCP address. Controller information is provided via DHCP Option 43.
3. saved the configuration
4. verified the code, successful
5. disabled wireless radios
6. installed the lightweight code using the command archive download-sw /safe flash:/ap3g1-rcvk9w8-tar.152-2.JB.tar.The installation was successful
7. rebooted the AP
After that nothing. The AP has not leased another IP address. The switchport is active. The APs MAC address is registering in the switches MAC address table. The AP is receiveing PoE from the switch. I noticed that this AP is only receiving 6.2W of power where the three are getting anywhere between 8.8W and 9.3W. I am unable to ping the old static IP of the AP too.
View 4 Replies
View Related
Nov 12, 2012
I have to prepare an 3600 Capwap AP for autonomous functionality!
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:
• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?
View 4 Replies
View Related
Aug 20, 2012
Cisco 1240AG converting to WEP to WPA
Access Point Model: Cisco 1240AG
System Software Filename: c1240-k9w7-tar.123-7.JA5
System Software Version: 12.3(7)JA5
Bootloader Version: 12.3(7)JA1
Access Point Model: Cisco 1131AG
Software: Cisco Aironet Desktop Utility 2.1.02
After converting encryption from WEP to WPA in a Cisco 1240AG in personal mode with an SSID name of example1 and Cisco 1131AG access point in personal mode with an ssid of example2; both with the same wpa passphrase, I created a new profile on the Cisco Aironet Desktop Utility with a new profile name as well as a WPA passphrase, but the desktop utility will only connect to the access point if one network name, example1 or example2, is entered.
View 18 Replies
View Related
Apr 5, 2013
is this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies
View Related
Jul 5, 2011
I have a Brand new AP that was bought for a site which has a controller, however it was never installed. I was wondering can you downgrade this AP to make it work in stand alone mode as a normal AP?
View 1 Replies
View Related
Jun 22, 2011
How can I convert exe file to sis format.
View 1 Replies
View Related
Jan 18, 2011
My desktop computer doesn't have a wireless card in it. i also have a laptop which does have a wireless card. I was wondering if there is a way i can take the wireless connection and re-transmit it to the desktop through ethernet. I have a 5-port switch. I don't really know much about networking. but i am knowledgeable in computers. laptop has windows 7 on it. i really would prefer to not buy a wireless card for the desktop.
View 2 Replies
View Related
Jan 1, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : 5.0.0
ISP : Beam Telecom
I recently bought this device in hurry . My ISP has directly connected RJ45 cable to my laptop .So i need to use this device for sharing internet to my wireless devices .IS it possible to convert Rj45 to Rj11 if so let me know the process .I have seen interenet about converting lan port to wan for TD-W8960 device . but GUI administration is quite different for my device .
View 1 Replies
View Related
Mar 5, 2012
I got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
URL
Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
View 4 Replies
View Related
Oct 18, 2012
Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
View 13 Replies
View Related
May 7, 2012
This is one I am having a hard time finding an answer for. How many clients can a 3600 AP support? For 150 clients on one of these, what would the throughput be for each client?
If my calculations are correct, the device can deliver 420 Mbps, which gives each client roughly 2.8Mbps. Is this correct?
View 9 Replies
View Related
Jun 25, 2012
if the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket? I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.
View 4 Replies
View Related
Sep 6, 2011
I have purchased a PAK for my 2 cisco 1921 routers .I would like to to configure IP SEC or SSL for VPN connectivity on the routers. How do i convert the PAK into a license?
View 1 Replies
View Related
Jul 22, 2012
I have an AP group on a Cisco 5508 WLAN controller. Currently, it is populated with 13 Cisco 1142 lightweight access points. When I try to add a Cisco 3602i access point to the group, I get the following error in NCS: Error: OfficeExtend requires primary, secondary, or tertiary controller management IP to be set.I am using DNS to allow my AP's to find the controller and they work just fine. Is there a reason I can't add the 3600 series AP's to the AP group?
View 13 Replies
View Related
May 8, 2012
i'm going to upgrade a 5508 wlc code from 7.0.116.0 to 7.1.91.0 to add 3600 series access points having it all manageable via WCS ver 7.0.230.0 it seems to be possible, as it is explained in the compatibility matrix found on [URL]now I have to download the file to the controller...
AIR-CT5500-K9-SPECIAL-7-1-91-0.aes
(direct update possible)
before doing that I'd like to know if I will loose my configuration on the controller i'm concerned about that because the release document is not clear:
- We highly recommend that you back up your controller's configuration files prior to upgrading the controller software. Otherwise, you must manually reconfigure the controller.
- For busy networks, controllers on high utilization, or small controller platforms it is advisable to disable the 802.11a/b/g networks as a precautionary measure.
- Step 5 Disable any WLANs on the controller.
- Step 19 Re-enable the WLANs......
- Step 22 If desired, reload your latest configuration file to the controller. (reload config after reenabling wlans?another controller another question .....: a cisco wlc 2100
found 2 update files
AIR-WLC2100-K9-7-0-230-0-ER.aes
AIR-WLC2100-K9-7-0-230-0.aes
why 2 update files this time? what file to update first?
View 9 Replies
View Related
Mar 6, 2013
I´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies
View Related
Mar 26, 2013
I have a 5508 controller with a bunch of 3600 Series APs. I did all the basic config on the controller and added all the APs through distribution port #1. Now I was trying to config a second interface ( port #2) and use it for the Guest SSID on a separate VLAN. After I rebooted the controller, it dumped all the APs. I would like to know if this is normal, If I need to enroll the APs everytime I reboot the controller.
View 1 Replies
View Related
Feb 3, 2013
I want to use the flexconnect in the same network where the wlc is located. Normally we will do it for over WAN and branch office. But I want to use in the same main office to avoid more bandwidth utilization on my distribution layer. Wlc is connected on Distribution switch.I want to do local switching in the access layer switch.
The below is the sample topology. But real topology contains nearly 200 AP's(3600 series) and 20 access switches and so on.....So there is a chance of 200 AP * 350 Mbps can flow on the distribution layer.So ,
1)If I use flexconnect any issues will be occuring?
2)Does it cause any impact on VOWLAN?
View 4 Replies
View Related
Aug 18, 2011
We have a VPN router(ASA5505) which connects to the client, B. IP address for one si 195.xx.xx.xx and for B it is 14.xx.xx.xx. Both can extablish a IPSEC VPN nicely.Now, B throws a condition that the IP coming thru the VPN has to be PUblic. They want it as such so that they can be routed across the VPN tunnel.It still can because the firewall does not do NAT.
View 5 Replies
View Related
Feb 7, 2011
How to convert a 3140 CAM to a CAS ? if so what software / licensing would be required and is there a documented process
View 1 Replies
View Related
Apr 3, 2013
I am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
View 9 Replies
View Related
Apr 23, 2013
I am don't need anything unusual and I would love to go with the 2600/3600 APs, unless mixing them up is a problem.
View 2 Replies
View Related
Oct 14, 2012
I am looking for the Maximum Power Settings Spec for the 3600 AP. The one from 2008 is too old. Does an update exist? The AP Spec itself does not show power levels by channel and regulatory domain which is what I need. If I can't get the spec, I will have to query the AP using "show ap config 802.11x apname" for each config I need.
View 1 Replies
View Related
Feb 8, 2013
Lost my access points to controller. Not sure if it was related to upgrade from 7.1 to 7.2, or something else.
The console log on APs shows;
*Mar 1 00:01:09.394: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 1 10:24:23.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 142.100.64.8 peer_port: 5246
*Jan 1 10:24:23.424: %DTLS-5-ALERT: Received FATAL : Certificate unknown alert from 142.100.64.8
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Bad certificate alert received from peer.
*Jan 1 10:24:23.424: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 142.100.64.8:5246
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
All 3500/3600 APs, had been in production for months.
View 1 Replies
View Related
Jun 3, 2012
I've got a client who purchased numerous 3600 series AP's (3602i to be exact) and would like to add them into their WLAN 4404 controller. They're currently on 5.x system code so I plan on getting them upgraded to the latest 7 code.
They currently have a number of AP's adding and working fine. Once the WLAN controller is upgraded, does anything specific need to be done within the WLAN gui to add in these new 3600 series AP's?
View 3 Replies
View Related
Sep 13, 2012
i have cisco wlc 2504 connected with cisco 3600 ap,now the customer required n bandwidth speed ,but in wlc am not able to enable n bandwidth for ssid.in radio policy of ssid also n bandwidth is not showing,only this bandwidth showing a/g,g,b/g, and all?
View 8 Replies
View Related
Dec 4, 2011
Customer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies
View Related
