Cisco Wireless :: 3600 AP Mounting Bracket
Jun 25, 2012if the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket? I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.
View 4 Replies
ADVERTISEMENT
Cisco Wireless :: Wall Mount Bracket For AIR-ANT5160V-R?
Apr 26, 2012I am looking for a wall mount bracket reference, for these 2 models of antennas :
- AIR-ANT5160V-R
- AIR-ANT2506
Something like that :I was not able to find any reference in cisco product list.
Linksys Wireless Router :: Is There A Wall Mount Bracket For E2500
Jan 4, 2012Is there a wall mount bracket for the E2500 or is there a way of attaching this to a wall.
View 1 Replies View RelatedCisco Wireless :: Wall Mounting A AIR-CAP3502I-E-K9
Nov 23, 2011I was under the impression that the AIR-CAP3502I-E-K9 is a ceiling mount AP only. Is any one using these as wall monuted AP's?
View 5 Replies View RelatedCisco Wireless :: AIR-ANT2430V-and AIR-ANT5140V Antenna Mounting
Mar 22, 2013 mounting for the above antenna types. see figures below.
The figures above, are the antenna mounting correct? For figure 1, can the two antennas be separated by 4" or more? For figure 2, the two antennas will be side by side.
Cisco Wireless :: AIR-ACCRMK1300 Mounting Manual Required
Jul 30, 2012I need some manual about how to use AIR-ACCRMK1300=.Is there any offical manual?
View 4 Replies View RelatedCisco Wireless :: Antenna Selection And Mounting For 2602
Feb 3, 2013We have a campus with both office and industial areas with various propagation problems. Historically I have been installing and maintaining access points in the 1200 range, the latest being the 1242. All these have a similar antenna setup based on diversity pairs.Since Cisco seems to be dropping the old series any week now I have been looking at the 2602 as a replacement.I can find no good documentation on antenna selection and mounting suggestions for these.If I want a proper omni coverage pattern with dual band antennas, do I just set them to a H form assuming the unit is sitting on a wall?
View 1 Replies View RelatedCisco Wireless :: Mounting 3500i Access Points (AP) To Ceiling
Jul 25, 2012mounting 3500i access points (AP) to the ceiling ...The ceiling is an Armstrong suspended ceiling with 24" mineral fiber drop ceiling..What are recommendations and best practice - mount AP under or above the ceiling? Initially, I considered the mounting options from Oberon Inc. (p/n :1064-00), but given the difficulty by purchasing this product in my country have to consider other options..I must say that the decision to mount the access point to the ceiling like this:
Now I looking a version of the mount АP with flush-mount kit for tiled ceilings (AIR-AP-BRACKET-3=)..
Cisco Wireless :: Mounting Blade For 1142 AP Identical To 2602?
Apr 14, 2013it seams, that the mounting blade for the 1142 access point and the 2602 access point are identical.
We have ordered the new 2602 with internal antennas for deploying WLAN in a new building, but I never hold this accesspoint in my hands. We have a few mounting blades in spare from the 1142 accesspoint. The question is, can I prepare the mounting of the 2602 access point with the 1142 mounting blade?
Cisco Wireless :: 3502i Ceiling Pole Mounting Options?
Jul 11, 2012I've got a number of 3502i's that I need to mount in a new classroom that does not have any ceiling (except the floor decking above). Ceiling is roughly 30-50' up. Contractors are going to run several 2" (or whatever we want) metal pipes from the ceiling down to a more reasonable level to mount the access points on and get below the hvac ducts/etc in the ceiling.
Problem is I can't find any bracket or mounting options for this! What are others using in this situation for mounting one of these access points onto a metal pipe such as this? I've checked Oberon Wireless, Terrawave and I don't see anything glancing through the product catalogs. Anyone mounting access points this way?
Linksys Wireless Router :: Mounting E4200 On Wall?
Feb 20, 2012How to mount the E4200 on a wall. Any smart ways to do it?
View 9 Replies View RelatedCisco Wireless :: 3502i Mounting Plate Welded To Security Hasp?
Feb 20, 2013Not sure why Cisco is shipping like this? It is a pain to mount them. Earlier we had option to slide out the Secuirty hasp.
View 1 Replies View RelatedLinksys Wireless Router :: E4200 Seems To Die When Mounting External Hard Drive
Jan 20, 2012I have realized that E4200 V1 I have, with 1.03 firmware, seems to be dying when I reboot it and it tries to load the USB HD I have connected to it. By die I mean the web server does not work anymore (http://192.168.1.1), and new computers can't connect to the router. I suspect it is due to the amount of files I have in the External Disk Drive -I used to have Media Server enabled, but I disabled it because this problem was happening, and I only left File Server enabled. Now since I moved many of my pictures to it, it seems even File Server is causing problems, and if neither one work for me, then this router does not justify its money, since that was the only reason I bought this E4200 hardware. These problems are solved in V2? Since it is still under warranty, I could try to exchange my V1 for a V2 version.
View 3 Replies View RelatedLinksys Wireless Router :: E4200 V2 - Cannot Access USB Storage Via Mounting Share
Jan 29, 2013I just bought an e4200 with firmware version 2.0.36 from Costco.I have set it up manually and have access to the internet for all of my wired and wireless devices.Unfortunately, I cannot access the USB storage via mounting a share, the media server or the FTP server. I have plugged in a USB storage device that is formatted with FAT32. The router detects it and allows me to create new shares in the Storage->Disk menu and Storage->Media Server menu - so I know it can read the device and see the folders. Strangely if I click "Scan All" in the Media Server, it finishes very quickly and never updates the "Last scanning time" field.There was a brief moment when the router showed up in the Network->Computer section of File Explorer, but I can't get it to show here again.
View 8 Replies View RelatedDD-WRT USB Not Mounting
Dec 21, 2012I was following a guide to install optware on my DD-WRT router but I couldn't get the drive mounted. It is a memory card (with USB adapter) with two partitions, both EXT3, one is 1gb and the other one is 13.65GB(ish). Here is my startup command:
[/QUOTE]mkdir /tmp/etc/config
echo "wget [URL]" >> /tmp/etc/config/fs.wanup
[Code].....
Cisco Switches :: Dual SG 300-10 Mounting And Cascading?
Oct 31, 2011SG 300-10 user manual states to not mount the switch on either side (I'm assuming this means the right or left ends as you face the front) and that they can be mounted either face-up or face down or flat). The specs further say that a 5" space must be "around all sides" of the unit. Silly question is what does "all sides of the unit' really mean? (of course given you must mount is somewhere). Also, given the little feet supplied with the unit, it is implicit to me the bottom needs to be only about 1/32" from the horizontal surface it is placed on. If this is true, can this unit be mounted face down on a shelf such as the Leviton 47612-UBK (it's allowing the mounted units to have airflow between the unit and the cabinet back) and have a second SG 300-10 mounted in front of the first that is seperated from the first by either the dual feet or use separation spacers that will fill the available shelf space and maximize the distance between the units - all without degrading the inherent reliability of either?
Lastly, The two SG 300-10's are reaching the internet through a LINKSYS E4200 router. Is it better to have each SG 300-10 occupying its own dedicated port on the router OR to cascade one SG 300-10 to the other SG 300-10 then one of the LINKSYS E4200 router? If the answer is each occupying their own dedicated LINKSYS port, then would it be prudent to load one SG 300-10 with the most active ethernet lines to allow the other SG 300's port power management to shut it down?
Cisco Wireless :: WCS And WLC Versions For 3600 WAP
Mar 5, 2012I got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
URL
Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
Cisco Wireless :: Use A 3600 For An Ethernet Bridge?
Oct 18, 2012Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
View 13 Replies View RelatedCisco Wireless :: Concurrent Users Per 3600?
May 7, 2012This is one I am having a hard time finding an answer for. How many clients can a 3600 AP support? For 150 clients on one of these, what would the throughput be for each client?
If my calculations are correct, the device can deliver 420 Mbps, which gives each client roughly 2.8Mbps. Is this correct?
Cisco Wireless :: Converting 3600 To Autonomous?
Jan 13, 2013I am not having much luck getting it converted via normal ways.
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing).
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar 1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..' Even if I set a static IP address.
Is there way to disable the join process while I upgrade the software? I guess fire up a controller for it to join. I hope I don't have to have a controller to convert these.
Cisco Switching/Routing :: C3650 Rack Mounting Pack
Mar 19, 2012i want to know, is c3650G or c3650X switches are already containing rack mounting pack or am i need to buy it seperatly?
View 3 Replies View RelatedCisco Wireless :: 5508 Can't Add 3600 Series AP To Group
Jul 22, 2012I have an AP group on a Cisco 5508 WLAN controller. Currently, it is populated with 13 Cisco 1142 lightweight access points. When I try to add a Cisco 3602i access point to the group, I get the following error in NCS: Error: OfficeExtend requires primary, secondary, or tertiary controller management IP to be set.I am using DNS to allow my AP's to find the controller and they work just fine. Is there a reason I can't add the 3600 series AP's to the AP group?
View 13 Replies View RelatedCisco Wireless :: 5508 WLC Code Upgrade / WCS AP 3600?
May 8, 2012i'm going to upgrade a 5508 wlc code from 7.0.116.0 to 7.1.91.0 to add 3600 series access points having it all manageable via WCS ver 7.0.230.0 it seems to be possible, as it is explained in the compatibility matrix found on [URL]now I have to download the file to the controller...
AIR-CT5500-K9-SPECIAL-7-1-91-0.aes
(direct update possible)
before doing that I'd like to know if I will loose my configuration on the controller i'm concerned about that because the release document is not clear:
- We highly recommend that you back up your controller's configuration files prior to upgrading the controller software. Otherwise, you must manually reconfigure the controller.
- For busy networks, controllers on high utilization, or small controller platforms it is advisable to disable the 802.11a/b/g networks as a precautionary measure.
- Step 5 Disable any WLANs on the controller.
- Step 19 Re-enable the WLANs......
- Step 22 If desired, reload your latest configuration file to the controller. (reload config after reenabling wlans?another controller another question .....: a cisco wlc 2100
found 2 update files
AIR-WLC2100-K9-7-0-230-0-ER.aes
AIR-WLC2100-K9-7-0-230-0.aes
why 2 update files this time? what file to update first?
Cisco Wireless :: Antennas Doesn't Work On AP 3600
Mar 6, 2013I´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies View RelatedCisco Wireless :: Adding 3600 Series To WLC 5508?
Mar 26, 2013I have a 5508 controller with a bunch of 3600 Series APs. I did all the basic config on the controller and added all the APs through distribution port #1. Now I was trying to config a second interface ( port #2) and use it for the Guest SSID on a separate VLAN. After I rebooted the controller, it dumped all the APs. I would like to know if this is normal, If I need to enroll the APs everytime I reboot the controller.
View 1 Replies View RelatedCisco Wireless :: Downgrade 3600 Capwap AP To Autonomous
Nov 12, 2012I have to prepare an 3600 Capwap AP for autonomous functionality!
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:
• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?
Cisco Wireless :: 3600 - Use FlexConnect In Same Network Where WLC Located?
Feb 3, 2013I want to use the flexconnect in the same network where the wlc is located. Normally we will do it for over WAN and branch office. But I want to use in the same main office to avoid more bandwidth utilization on my distribution layer. Wlc is connected on Distribution switch.I want to do local switching in the access layer switch.
The below is the sample topology. But real topology contains nearly 200 AP's(3600 series) and 20 access switches and so on.....So there is a chance of 200 AP * 350 Mbps can flow on the distribution layer.So ,
1)If I use flexconnect any issues will be occuring?
2)Does it cause any impact on VOWLAN?
Cisco Infrastructure :: 2911 - Side Mounting Hole Dimension Schematic
Aug 17, 2011My mechanical engineer needs detailed measurements for the hole patterns on the sides of the Cisco 2911. Where I could find this?
I've searched and read the installation docs, which shows pictures of the units. Although useful, they does not show exact measurements, angles, and hole diameters.
Cisco Wireless :: 3600 Access Points In Bridge Mode
Apr 3, 2013I am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
Cisco Wireless :: Mixing And Connecting 1262 With 2600 And 3600
Apr 23, 2013I am don't need anything unusual and I would love to go with the 2600/3600 APs, unless mixing them up is a problem.
View 2 Replies View RelatedCisco Wireless :: Maximum Power Settings Spec For 3600 AP?
Oct 14, 2012I am looking for the Maximum Power Settings Spec for the 3600 AP. The one from 2008 is too old. Does an update exist? The AP Spec itself does not show power levels by channel and regulatory domain which is what I need. If I can't get the spec, I will have to query the AP using "show ap config 802.11x apname" for each config I need.
View 1 Replies View RelatedCisco Wireless :: 3500 / 3600 - Post 7.2.111-3 Upgrade Lost All APs?
Feb 8, 2013Lost my access points to controller. Not sure if it was related to upgrade from 7.1 to 7.2, or something else.
The console log on APs shows;
*Mar 1 00:01:09.394: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 1 10:24:23.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 142.100.64.8 peer_port: 5246
*Jan 1 10:24:23.424: %DTLS-5-ALERT: Received FATAL : Certificate unknown alert from 142.100.64.8
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Bad certificate alert received from peer.
*Jan 1 10:24:23.424: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 142.100.64.8:5246
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
All 3500/3600 APs, had been in production for months.
Cisco Wireless :: Adding 3600 Series AP To 4404 WLAN?
Jun 3, 2012I've got a client who purchased numerous 3600 series AP's (3602i to be exact) and would like to add them into their WLAN 4404 controller. They're currently on 5.x system code so I plan on getting them upgraded to the latest 7 code.
They currently have a number of AP's adding and working fine. Once the WLAN controller is upgraded, does anything specific need to be done within the WLAN gui to add in these new 3600 series AP's?