it seams, that the mounting blade for the 1142 access point and the 2602 access point are identical.
We have ordered the new 2602 with internal antennas for deploying WLAN in a new building, but I never hold this accesspoint in my hands. We have a few mounting blades in spare from the 1142 accesspoint. The question is, can I prepare the mounting of the 2602 access point with the 1142 mounting blade?
We have a campus with both office and industial areas with various propagation problems. Historically I have been installing and maintaining access points in the 1200 range, the latest being the 1242. All these have a similar antenna setup based on diversity pairs.Since Cisco seems to be dropping the old series any week now I have been looking at the 2602 as a replacement.I can find no good documentation on antenna selection and mounting suggestions for these.If I want a proper omni coverage pattern with dual band antennas, do I just set them to a H form assuming the unit is sitting on a wall?
View 1 Replies View RelatedI have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
I have an 2602 AP. Recently I tried to move it from one controller to another, however in doing so the image must have gotten corrupted. So no I'm in AP ROMMON. I can't find any recovery procedures specifically for the 2600's, but I what I did find doesn't seem to work :
ap: set IP_ADDR 10.4.208.3
ap: set NETMASK 255.255.255.0
ap: set DEFAULT_ROUTER 10.4.208.1
[Code].....
We typically use the 2602 series AP in lightweight mode, however I have a scenario where we are going to be installing one with the stand-alone software. I understand that we will not be able to utilze certain features that you get with the WLC such as RRM, rogue detection, and clean air.
We do want to utilze both the 2.4GHZ and 5GHZ bands. In order to do this with the 2602 stand-alone AP, will we have to configure 2 separate SSID's? I really do not want to do this to if I do not have to to minimize confusion for clients.
i'm configuring a standalone AP 2602 with IOS 15.2.When i connect to AP from my notebook i only get 65Mb speed, when i connect to other APs from the notebook my speed connection 150-300Mb.
What configuration(CLI) do i need to be able to connect to the AP on connection speed to 130-450Mb ? Currently I connect to SSID with WPA2 encryption and "speed default" on radio 0 interface.
Instead of stocking every known AP and every external connector, I would like to query which APs to stock for general site surveys....
I have 2 customers that will require surveys in the near future...one plans on using the 2602e AP, and the other a 3602e AP. I have read somewhere that the 1140 makes an excellent proxy for the 2602 and several other Cisco APs (as the RF characteristics are similar) so that I only have to stock that one AP to use for those site surveys- but I haven't seen any recommendations about the 3600 series AP yet...
What AP to stock for doing Cisco site surveys? Maybe one or two models only?
Virgin media superhub was swapped for a new identical one as some users were unable to connect, but my connection was fine. When i booted my system up after it was configured by virgin I could see all connections but clicking on any "connect" button doesn't yield any form of output from the computer. Password problem? I dont get a response whenever I click "connect" on any of the other 20 wireless connections that i'm picking up, none of them being mine. When trying to add a new network from "network and sharing centre" via "set up a new connection or network" button on the mainpage or "add" button on the "manage wireless networks" tab yields the same, absolutely no reaction from the system.Now, I only add this info for science of deduction purposes, because it is truly baffling me right now, but when i first discovered the problem and went into "devices and printers" in contr panel and "add a device" my computer paused and then BSOD'd.
Things I have tried:
Updated the network card drivers Ran start up recovery - no problems detected after 20x running Logged onto the superhub through another users system and added my mac address to allowed lists, reserved i.p. address - both on and off, all combinations Pressed the wireless card button on the back of my system on and off, repeatedly Disabled/enabled network adapters in device manager Run winsock and dns flushes, ip release and renewals (e.g. things like "netsh int ip reset; netsh winsock reset; ipconfig release;renew)
Each and every troubleshooter All the usual power issues, from setting maximum performance on the network card to unplugging and socketing the router main repeatedly Administrative tools-services-dhcp client-start&auto Tcp/IP protocols-ip and dns configured automatically?
*Haven't tried (last resorts)* Reinstall windows Remove, inspect and possibly replace or just refit network card and factory reset
Give Richard Branson a slap Observations/Details Everyone, EVERYONE else can connect to the network, no problem I have full strength signal to the connection I know the password and it certainly hasnt changed All we did was swap identical routers! Logged into my other windows on a partition (original user account, messy so partitioned and made a clean install, but this was long ago and no network issues ever existed) and have the old exclamation mark over signal bars - troubleshooting it causes nothing, but at least the adding network functions yields results and it says im technically connected to the router - ive tried all noted fixes above on this windows install also.
*ipconfig*
network adapter "connection specific DNS suffix:<blank>"
"ipv4address: 192.168.0.4(preferred)"
"subnet mask 255.255.255.0"
"default gateway: 192.268.0.1"
"dhcp server: 192.168.0.1"
"dns servers: 194.168.4.100, 194.168.8.100"
All other adapters are "media disconnected"
Pc specs
Win7 x64
Intel Q6600
Atheros ar922x wireless card
I have the D-link dir-655 wireless router connected at my cable modem and i HAD a d'link switch patched in about 40 feet away. The switch died after 45 days.To solve the problem and extend my network I purchased an identicaldir-655 router to replace the switch. My thought was that i would configure both routers the same and be able to use the same network settings to access the network throughout my house.It didn't work.I even tried changing the IP address on the second router but it did something to the modem. After resetting everything, the original router works again. D'link support says what i am trying cannot be done, but i know it can.
View 1 Replies View RelatedMy wireless network signal is great on the first floor, but is weak on the second floor. I have tried different antennas and various locations for the antennas, but with little improvement. I prefer not to purchase signal amplifier. I have a second identical router. Can it be connected to the current router (LAN output) and by way of a cat5 cable, placed on the second floor to boost the second floor wireless signal?
View 8 Replies View RelatedI have a problem, where we are installing a Cisco 2602 access piont, the AP is getting power as the lights are on (changing colors Green, White, Red). In the switch side the LED for the interface is blinking green only when I chosse PoE. Also I cannot see the AP in CDP neighbours.
It seems to be a physical problem but the cable is tested and showing connected for all pairs and parallal (straight) connection.
Access Point was connected directly to the same interface (I mean with a patch cable to the switch) and working
When I connect my DSL modem to my DLINK wireless router, two identical DEFAULT connections appear in my wireless connection detection. Both will only connect locally.
View 5 Replies View RelatedI have several 2602 AP's that I want to operate in FlexConnect mode. The WLC is at a central HQ and the Ap's are remote. There are central radius servers at the HQ for the wlans. At the remote lcoation, there is a local radius server we want to use for the primary radius server for these AP's. This radius server has been added to the WLC. I have setup a FlexConnect Group, designated the the primary and secondary servers, and then added the AP's to the group. It does not look like radius requests are being sent to the local controller.
For this to work, do we have to check the box under the wlan for FlexConnect Local Auth? Currently, we only have FlexConnect local switching selected.
I was under the impression that the AIR-CAP3502I-E-K9 is a ceiling mount AP only. Is any one using these as wall monuted AP's?
View 5 Replies View Relatedif the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket? I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.
View 4 Replies View Related mounting for the above antenna types. see figures below.
The figures above, are the antenna mounting correct? For figure 1, can the two antennas be separated by 4" or more? For figure 2, the two antennas will be side by side.
I need some manual about how to use AIR-ACCRMK1300=.Is there any offical manual?
View 4 Replies View Relatedmounting 3500i access points (AP) to the ceiling ...The ceiling is an Armstrong suspended ceiling with 24" mineral fiber drop ceiling..What are recommendations and best practice - mount AP under or above the ceiling? Initially, I considered the mounting options from Oberon Inc. (p/n :1064-00), but given the difficulty by purchasing this product in my country have to consider other options..I must say that the decision to mount the access point to the ceiling like this:
Now I looking a version of the mount АP with flush-mount kit for tiled ceilings (AIR-AP-BRACKET-3=)..
I've got a number of 3502i's that I need to mount in a new classroom that does not have any ceiling (except the floor decking above). Ceiling is roughly 30-50' up. Contractors are going to run several 2" (or whatever we want) metal pipes from the ceiling down to a more reasonable level to mount the access points on and get below the hvac ducts/etc in the ceiling.
Problem is I can't find any bracket or mounting options for this! What are others using in this situation for mounting one of these access points onto a metal pipe such as this? I've checked Oberon Wireless, Terrawave and I don't see anything glancing through the product catalogs. Anyone mounting access points this way?
How to mount the E4200 on a wall. Any smart ways to do it?
View 9 Replies View RelatedNot sure why Cisco is shipping like this? It is a pain to mount them. Earlier we had option to slide out the Secuirty hasp.
View 1 Replies View RelatedI have a question regarding WISM2 DP and licensing.
Suppose i have a WISM2 with 7.0, 500AP license today and i activate WISM2-DP by upgrading to 7.2,Do i get 500 AP capacity for free (total 1000AP) or do i get 250APs on each WISM2-blade ?
If i get 500APs for free, why is Cisco selling an expensive licensed 1000 AP WISM2 ? I better buy a single-plane 500AP-WISM2 and upgrade it myself then...50% profit.
Is this the same for a WISM2-300 (supporting 300 APs) ?When i activate WISM2-DP here, do i get an extra 300 AP or an extra 500 APs ? Or 150AP on each blade ?
I have realized that E4200 V1 I have, with 1.03 firmware, seems to be dying when I reboot it and it tries to load the USB HD I have connected to it. By die I mean the web server does not work anymore (http://192.168.1.1), and new computers can't connect to the router. I suspect it is due to the amount of files I have in the External Disk Drive -I used to have Media Server enabled, but I disabled it because this problem was happening, and I only left File Server enabled. Now since I moved many of my pictures to it, it seems even File Server is causing problems, and if neither one work for me, then this router does not justify its money, since that was the only reason I bought this E4200 hardware. These problems are solved in V2? Since it is still under warranty, I could try to exchange my V1 for a V2 version.
View 3 Replies View RelatedI just bought an e4200 with firmware version 2.0.36 from Costco.I have set it up manually and have access to the internet for all of my wired and wireless devices.Unfortunately, I cannot access the USB storage via mounting a share, the media server or the FTP server. I have plugged in a USB storage device that is formatted with FAT32. The router detects it and allows me to create new shares in the Storage->Disk menu and Storage->Media Server menu - so I know it can read the device and see the folders. Strangely if I click "Scan All" in the Media Server, it finishes very quickly and never updates the "Last scanning time" field.There was a brief moment when the router showed up in the Network->Computer section of File Explorer, but I can't get it to show here again.
View 8 Replies View RelatedI've got 4 identical Windows 7 PC's but one of the PCs cannot access the others for file sharing and does not have access to the printer which is hosted on one of the other computers.Strangely, all 4 computers CAN access the internet through the one LAN hub and all 4 computers CAN play network games with each other.
View 10 Replies View RelatedI have a Cisco 1841 router with Fa0/0, Fa0/1 and Se0/0/0:0 interfaces. Fa0/0 is facing the LAN. At the moment WAN interface is Se0/0/0:0. It has following configuration:
View 5 Replies View RelatedI have 2 ASA5510's acting as routers/firewalls, setup on a LAN, each one pointing to a different gateway (different ISPs), and the exact same VLANs set up as sub-interfaces on each of these. Both act as DHCP relays to a Windows Server 2008 DHCP server. All the Trunking has been setup and works. When I Untag a switch port, and point it to whichever gateway?
View 2 Replies View RelatedEnvironment :AP 2602, WLC 5508 V7.4, ISE 1.1.2, Prime Infras 1.2
For a specific SSID, we use MAC address as 1 of the conditions to authorize access only for the company-owned mobiles (smartphones and tablets), the other condition being, for the mobile, to present a valid AD user/password;this way, the so-called BYODs are rejected since this is the rule within this company ;The difficulty with this approach is the fact that there is no way in ISE Identities Endpoints nor Groups to associate a user-friendly name to the MAC address of the mobiles, which makes very tedious some actions such as a search in the ISE authentication Log based on the MAC address value itself;the question is just to know if it is planned to add a new field in Identities Endpoints definition that would allow to associate a user-friendly name to a MAC address, for future ISE versions,
I was following a guide to install optware on my DD-WRT router but I couldn't get the drive mounted. It is a memory card (with USB adapter) with two partitions, both EXT3, one is 1gb and the other one is 13.65GB(ish). Here is my startup command:
[/QUOTE]mkdir /tmp/etc/config
echo "wget [URL]" >> /tmp/etc/config/fs.wanup
[Code].....
We have bought four identical 3750X switches with identical SW-images: 12.2(55)SE3 C3750E-UNIVERSALK9-M
We initially connected two switches, this resulted in forming a stack.With the other two switches we wanted to do the same thing. However, we received the following message:
%STACKMGR-5-MAJOR_VERSION_MISMATCH: Major Version Mismatch (Local 1 - Received 6) with neighbor-1
Both switches will not see each other and the output of show switch stack-ports shows only one switch and both stack ports as being Down.
I did some digging using the show platform stack-manager all command to find out that three of the 3750X's have the stack version number 1.45 and one has 6.45. This would obviously indicate the reason behind the mismatch, but the SW-versions on all new switches are identical!
Checking the CISCO site explains that mismatching of Major version is critical:
Major Version Number Incompatibility Among Switches
Switches with different major Cisco IOS software versions usually have different stack protocol versions. Switches with different major version numbers are incompatible and cannot exist in the same switch stack.
That's all I could find. Nothing about changing the major version number, so all I can suspect is that IOS version needs to be the same.
SG 300-10 user manual states to not mount the switch on either side (I'm assuming this means the right or left ends as you face the front) and that they can be mounted either face-up or face down or flat). The specs further say that a 5" space must be "around all sides" of the unit. Silly question is what does "all sides of the unit' really mean? (of course given you must mount is somewhere). Also, given the little feet supplied with the unit, it is implicit to me the bottom needs to be only about 1/32" from the horizontal surface it is placed on. If this is true, can this unit be mounted face down on a shelf such as the Leviton 47612-UBK (it's allowing the mounted units to have airflow between the unit and the cabinet back) and have a second SG 300-10 mounted in front of the first that is seperated from the first by either the dual feet or use separation spacers that will fill the available shelf space and maximize the distance between the units - all without degrading the inherent reliability of either?
Lastly, The two SG 300-10's are reaching the internet through a LINKSYS E4200 router. Is it better to have each SG 300-10 occupying its own dedicated port on the router OR to cascade one SG 300-10 to the other SG 300-10 then one of the LINKSYS E4200 router? If the answer is each occupying their own dedicated LINKSYS port, then would it be prudent to load one SG 300-10 with the most active ethernet lines to allow the other SG 300's port power management to shut it down?
i want to know, is c3650G or c3650X switches are already containing rack mounting pack or am i need to buy it seperatly?
View 3 Replies View RelatedMy mechanical engineer needs detailed measurements for the hole patterns on the sides of the Cisco 2911. Where I could find this?
I've searched and read the installation docs, which shows pictures of the units. Although useful, they does not show exact measurements, angles, and hole diameters.