Swapped Identical Routers / Cannot Connect To Wireless Connections

Mar 2, 2013

Virgin media superhub was swapped for a new identical one as some users were unable to connect, but my connection was fine. When i booted my system up after it was configured by virgin I could see all connections but clicking on any "connect" button doesn't yield any form of output from the computer. Password problem? I dont get a response whenever I click "connect" on any of the other 20 wireless connections that i'm picking up, none of them being mine. When trying to add a new network from "network and sharing centre" via "set up a new connection or network" button on the mainpage or "add" button on the "manage wireless networks" tab yields the same, absolutely no reaction from the system.Now, I only add this info for science of deduction purposes, because it is truly baffling me right now, but when i first discovered the problem and went into "devices and printers" in contr panel and "add a device" my computer paused and then BSOD'd.

Things I have tried:

Updated the network card drivers Ran start up recovery - no problems detected after 20x running Logged onto the superhub through another users system and added my mac address to allowed lists, reserved i.p. address - both on and off, all combinations Pressed the wireless card button on the back of my system on and off, repeatedly Disabled/enabled network adapters in device manager Run winsock and dns flushes, ip release and renewals (e.g. things like "netsh int ip reset; netsh winsock reset; ipconfig release;renew)
Each and every troubleshooter All the usual power issues, from setting maximum performance on the network card to unplugging and socketing the router main repeatedly Administrative tools-services-dhcp client-start&auto Tcp/IP protocols-ip and dns configured automatically?

*Haven't tried (last resorts)* Reinstall windows Remove, inspect and possibly replace or just refit network card and factory reset
Give Richard Branson a slap Observations/Details Everyone, EVERYONE else can connect to the network, no problem I have full strength signal to the connection I know the password and it certainly hasnt changed All we did was swap identical routers! Logged into my other windows on a partition (original user account, messy so partitioned and made a clean install, but this was long ago and no network issues ever existed) and have the old exclamation mark over signal bars - troubleshooting it causes nothing, but at least the adding network functions yields results and it says im technically connected to the router - ive tried all noted fixes above on this windows install also.

*ipconfig*
network adapter "connection specific DNS suffix:<blank>"
"ipv4address: 192.168.0.4(preferred)"
"subnet mask 255.255.255.0"
"default gateway: 192.268.0.1"
"dhcp server: 192.168.0.1"
"dns servers: 194.168.4.100, 194.168.8.100"

All other adapters are "media disconnected"

Pc specs
Win7 x64
Intel Q6600
Atheros ar922x wireless card

View 14 Replies


ADVERTISEMENT

When Connecting DSL Modem Into Wireless Router 2 Identical Default Connections Appear

May 17, 2011

When I connect my DSL modem to my DLINK wireless router, two identical DEFAULT connections appear in my wireless connection detection. Both will only connect locally.

View 5 Replies View Related

D-link Dir-655Connecting Two Identical Wireless Routers On One Network?

Oct 25, 2012

I have the D-link dir-655 wireless router connected at my cable modem and i HAD a d'link switch patched in about 40 feet away. The switch died after 45 days.To solve the problem and extend my network I purchased an identicaldir-655 router to replace the switch. My thought was that i would configure both routers the same and be able to use the same network settings to access the network throughout my house.It didn't work.I even tried changing the IP address on the second router but it did something to the modem. After resetting everything, the original router works again. D'link support says what i am trying cannot be done, but i know it can.

View 1 Replies View Related

Cisco Switching/Routing :: ASA5510 / Two Routers On Same Physical Lan With Identical VLANs On Each?

Mar 17, 2013

I have 2 ASA5510's acting as routers/firewalls, setup on a LAN, each one pointing to a different gateway (different ISPs), and the exact same VLANs set up as sub-interfaces on each of these. Both act as DHCP relays to a Windows Server 2008 DHCP server. All the Trunking has been setup and works. When I Untag a switch port, and point it to whichever gateway?

View 2 Replies View Related

Home Network :: Swapped Wireless 150mb/s For 300 Mb/s Mimo For Faster Speed?

Mar 30, 2012

Swapped wireless routers 150mbps for 300 mbps mimo for faster speed Will I see that additional speed on my wireless LAN?IOW, what conditions must be met before I can reap additional speed with my 11g laptop or my 11n hp Touchpad running both webOS and CyanogenMode 9?

Swapped
Rosewill RNX-N150RT 802.11b/g/n
for
Rosewill RNX-N300RT 802.11b/g/n(2T2R MiMo)

View 1 Replies View Related

Routers / Switches :: How To Connect 3 Outside Connections And Route Them Properly

Jul 19, 2012

We are planning 3 Internet Connections into our building. 1 will be for actual Internet traffic, 2nd for Voip phone system, and 3rd for internal network for Active Directory...etc. Oh the AD servers are controlled by another business so technically this line is still considered and outside line and is a T1. What I need to know is how best to make this all work so that our internet phones use the VOIP system, computers can log into the domain and access that network but use the Internet network for actual internet traffic? We were considering a series of managed switches and creating 3 VLAN's but I'm thinking we instead need a new router that all 3 networks connect to and dishes out DHCP to computers and phonesn example network is below.192.168.1.x ----> Internet (all computers use for internet traffic)72.10.10.x ----> VOIP (All physical and software phones use this network)10.10.10.x -----> Connection to external company that controls our network and has domain controllers, mainframe...etc.

View 2 Replies View Related

Weak Wireless Signal - Connecting Second Identical Router?

Dec 20, 2011

My wireless network signal is great on the first floor, but is weak on the second floor. I have tried different antennas and various locations for the antennas, but with little improvement. I prefer not to purchase signal amplifier. I have a second identical router. Can it be connected to the current router (LAN output) and by way of a cat5 cable, placed on the second floor to boost the second floor wireless signal?

View 8 Replies View Related

Cisco Wireless :: Mounting Blade For 1142 AP Identical To 2602?

Apr 14, 2013

it seams, that the mounting blade for the 1142 access point and the 2602 access point are identical.
 
We have ordered the new 2602 with internal antennas for deploying WLAN in a new building, but I never hold this accesspoint in my hands. We have a few mounting blades in spare from the 1142 accesspoint. The question is, can I prepare the mounting of the 2602 access point with the 1142 mounting blade?

View 2 Replies View Related

4 Identical PC's But One Cannot Access Network?

Nov 13, 2012

I've got 4 identical Windows 7 PC's but one of the PCs cannot access the others for file sharing and does not have access to the printer which is hosted on one of the other computers.Strangely, all 4 computers CAN access the internet through the one LAN hub and all 4 computers CAN play network games with each other.

View 10 Replies View Related

Difference Between Wired Connections And Wireless - Routers

Feb 6, 2012

I see 350 and 450 Mbps speeds Router but I think that that only refers to wireless. Are there differences in the speed of a wired connection for all these new routers or are they all the same?

View 7 Replies View Related

Cisco :: Configure Two Ports With Identical IP Address Configuration

May 4, 2012

I have a Cisco 1841 router with Fa0/0, Fa0/1 and Se0/0/0:0 interfaces. Fa0/0 is facing the LAN. At the moment WAN interface is Se0/0/0:0. It has following configuration:

View 5 Replies View Related

Routers / Switches :: Wireless Connections Will Only Allow One Computer At A Time?

May 24, 2012

Had laptop connecting wirelessly perfect with no problems. We then added another laptop and PSP 3 to the house hold. Any of the 3 devices will connect to the internet via wireless but ONLY one at a time. If you are connected with one and turn on one of the others it will kick the one off that you were on and only 1 device can use wireless at a time?

View 4 Replies View Related

Cisco Routers :: RVS4000 - Multiple Internet Connections / Routers Sharing Printers?

Sep 11, 2011

I have 2 internet connections in my office one via Verizon Fios and another  one via the local cable company. On the fios connection I have an RV042 VPN  router and on the Cable company connection I have an rvs4000 router, I would  like to know if there is a way I can connect the 2 so I can share a printer I  have on one of the 2 networks from the other network without using the VPN  feature, like via an ethernet cable connected between the 2 and some kind of  static route maybe?

View 6 Replies View Related

Cisco Routers :: Acceptable Number Of Wireless Connections To WRVS4400N?

May 1, 2013

What would be an acceptable number of wireless connections to a WRVS4400N router? I'm working in the IT department for a new company, and one of the offices complains that using VoIP and doing large file transfers are constantly a problem.  They are all connecting wirelessly to the WRVS4400N. I managed to vpn in and connect to the web interface of the router, and it shows that there are 30 devices connected wirelessly to it.  However, when people plug into the wall jack VoIP and data seem to work fine.I can't find any info on what a best practice would be for number of wireless connections to the router.  There's no Vlans setup on it from what I can tell, so that may be my next step, to separate data and voice traffic.        

View 2 Replies View Related

Wireless Connections Available But Cannot Connect

Mar 2, 2013

I am having the same problem with a new computer via my home wireless connection. The computer will not connect to the internet at all while at home, but it will connect to the internet in other locations (like at school). My other computer connects to the internet without a problem. The computer that isn't working can recognize that there are wireless connections available, but cannot connect. I got the same message "the default gateway is not available."

View 14 Replies View Related

Cisco Routers :: SRP 527W - Wireless Connections / Unable To Update Firmware

Jul 18, 2011

I have recently acquired one of these routers. I thought, being a Cisco product, it would be the bee's knees. It is not.  After finally getting the network set up - no mean feat, although I do not claim any expertise, but had to resort to some other network management software to finally get it all running - the router drops either the WAN connection or the wireless connection many times a day.  The laptops often show as being connected to the network/router, but are unable to access either the internet, or the router via the browser. Re-booting the router is the fix, but, hey, I can achieve that sort of performance with any old $20 router - none of my old Net gear routers was this troublesome.
 
The permanent fix would seem to be a firmware upgrade, but guess what?  The only options available under the "Administration" tab are time setting and switch settings - no firmware upgrade. The supplied firmware is 1.01.09(001) Apr 7 2010.  Why these products are supplied, as new, without the latest firmware installed beats me, but there you go.

View 4 Replies View Related

Cisco Switching/Routing :: 3750 - Major Version Mismatch On Identical Switches

Apr 3, 2012

We have bought four identical 3750X switches with identical SW-images: 12.2(55)SE3          C3750E-UNIVERSALK9-M
 
We initially connected two switches, this resulted in forming a stack.With the other two switches we wanted to do the same thing. However, we received the following message:
 
%STACKMGR-5-MAJOR_VERSION_MISMATCH: Major Version Mismatch (Local 1 - Received 6) with neighbor-1
 
Both switches will not see each other and the output of show switch stack-ports shows only one switch and both stack ports as being Down.
 
I did some digging using the show platform stack-manager all command to find out that three of the 3750X's have the stack version number 1.45 and one has 6.45. This would obviously indicate the reason behind the mismatch, but the SW-versions on all new switches are identical!
 
Checking the CISCO site explains that mismatching of Major version is critical:
 
Major Version Number Incompatibility Among Switches

Switches with different major Cisco IOS software versions usually have different stack protocol versions. Switches with different major version numbers are incompatible and cannot exist in the same switch stack.
 
That's all I could find. Nothing about changing the major version number, so all I can suspect is that IOS version needs to be the same.

View 5 Replies View Related

Connect To 2 Wireless Connections From One Laptop At Same Time?

Nov 9, 2011

I have two wireless connections at home from 2 different ISPs. How can make my laptop connect to both routers at the same time to make use of them?

View 1 Replies View Related

Cannot Get Laptop To Connect To Anything But Unsecured Wireless Connections

Jan 14, 2012

I cannot get my laptop to connect to anything but unsecured wireless connections. Ipconfig says Wlan media disconnected. Tried ipconfig /release, renew. Still nothing.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G2 - Connect Ethernet Switch (for Hardwired Connections)?

Dec 29, 2011

In my main office, I have a cable modem which is connected to my main E4200 router. All of my equipment (except my Ooma) is served by the E4200. The E4200 broadcasts a wireless network.In my basement, I have a Wii / entertainment center. The E4200 signal from upstairs isn't strong enough to stream video.
 
I bought the WET610N and have successfully set it up to interact with the E4200 wirelss network. I can hardwire my laptop to the WET610N and verify the internet works greatHowever, the Wii must connect over wireless. I have other equipment in the basement which would benefit from an internet connection. So, I want to A) connect the ESXS88W 10/100 8-port workgroup switch I have to the WET610N *AND* also broadcast a wireless signal in my basement (assuming the wireless network I see in the basement is the same "old" one from upstairs which has not benefited from the WET610N).
 
How can I set up my WRT54G2 to broadcast a wireless signal in the basement so that it leverages the E4200 signal served by the WET610N, while also having the workgroup switch offer hardwired connections to my other equipment (like Dish Network receiver)? It doesn't seem to work by just plugging the WRT54G2 into the workgroup switch.

View 2 Replies View Related

Routers / Switches :: Increasing Connections And Security?

Jan 24, 2012

I'm not sure about my title, it;'s the best I could come up with. I have approximately 7 computers, two iPhone, and iPad, wireless printers and a network attached storage. Most are connected over via wifi, the exceptions being one pc, the nas and a printer. I plan to add six more devices plus some ip cams. The way the router or network is configured whenever a guest connects to our wifi they can "see" our computers. I haven't been able to tell if they can see the files or just the name of the computer. Question 1: How can I tell if the guests are able to access the data on our computers or networked drive? Question 2: If I add a switch will I need to do anything special with regard to security?

View 1 Replies View Related

Routers / Switches :: How To Secure Network Connections

Oct 2, 2011

My itty bitty manual just shows on how to hook up my router via cable modem...nothing on how to secure it. I go into setup of the router and see where one can add info but am at a loss what to enter. I tried, merely by guessing, applied the info, and screwed up my networking. I couldn't even get into my router to revert back, cause i couldn't get on line...finally i reset manually my router and all is well again, except when i see a list of nearby network users, mine is the only one that says unsecured.

View 25 Replies View Related

Cisco Routers :: Rv180 Dropping LAN Connections?

Mar 13, 2013

I just recieved a new RV180 yesterday and it will not connect to my switch. Router was updated to the newest firmware, reset to factory settings. I did change the ip and ip range. Router works fine with one computer attached direct. As soon as I connect my sf300-24P to it, the WAN and LAN lights all light up and then go out. Only the WAN will light back up. I have no connectivity to the router. I plug the laptop to the router directly and no LAN lights come on and can not see the router with arp -a.

View 6 Replies View Related

Cisco Routers :: RVS-4000 Dropping Ip Connections

Apr 25, 2012

I have my RVS-4000 configured using static IP addresses in the LAN configuration.  The users use DHCP to get their addresses (for the most part, a couple may have static IPs set on the computer). I have the maximum number of DHCP users set to 1 to restrict the ability of people to log in to the system. That one address is locked down.
 
The internal address of the router is set to 182.168.2.1.  It doesn't conflict with anything on my network. I have 35 static IPs. About half of them are uing IP Based ACL to limit their access time but that doesn't seem to bear any relationship to what drops off.  
 
Almost daily one or more of the users will lose their IP address and a hard reset of the router is required.  The user this happens to seems random and it may be more than one but seldom all of them.  The network includes Windows7 (Home & Pro), a FreeNAS, Macs (Leopard and Snow Leopard), iPad, iPods, an iPhone and an AirPort Extreme used as a WAP (DHCP is disabled).  The AirPort is plugged directly into the router and has a staic ip on the RVS-4000 but is set to DHCP.  It seems to be the most common problem child.

View 3 Replies View Related

Cisco Routers :: RV215W Not Responding To Outside Connections?

May 5, 2013

The RV215W is not responding to the https port, the VNC port 5900 is also failing to respond. VPN still works, I will go in and reboot and it will work again. It works for 1 day and fails to connect again.
 
Latest Firmware is already install, I don't know what else to do.

View 2 Replies View Related

Cisco Routers :: WAP4410 Dropping Connections

Aug 10, 2011

Model: WAP4410N-A V02
Firmware version: 2.0.3.3
 
Deployed 3 of these as WAPs. No repeaters. They are spaced at least 50 feet apart over three offices, each in a server or switch room.
 
Across multiple laptops, and multiple WAPS, the wireless will function fine for a while with good bandwidth..then the connection will simply drop. By simply resetting the connection on the laptop or turning the wireless off then on, the connection typically returns, at least for a period of time before it drops again.
 
I’ve tried these configured as three separate SSIDs on identical channels, as well as one SSID for all three with different channels (preferred for a seamless wireless), and the behavior does not change either way.Based on some other threads, I tried forcing the LAN port speed to 100 mbps, but the problem persists.

View 7 Replies View Related

Cisco Routers :: RV042G Dual WAN Connections?

Jun 5, 2013

We are connecting to a Cisco DPC3825 cable modem supplied by our ISP.  It has been configured to act as a switch only.  They have supplied us with 2 static IP addresses.
 
When each WAN port is connected individually, everything is fine.  I see the IP addresses on the respective WAN port, and it is working fine.
 
When I connect both WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes completely non-responsive through its web interface.
 
How do I get the RV042G working with both WAN ports connected?

View 3 Replies View Related

Cisco Routers :: RV120W To Allow For Remote VPN Connections

Apr 5, 2011

I'm trying to configure my RV 120W to allow for remote VPN connections by a few salesmen. I tried to set it up through the wizard, but the menu tells me that the Remote Information (IP or FQDN) is assnged when they client connects but I HAVE to put something in there. I tried it with my IP information and can't connect either, but I have a feeling that is my PC's issue with Windows 7 (it just sits on verifying uername and password and then locks up explorer). I don't see anything in the logs about it attempting to connect or anything from my machine- I'm going to work with another but that still doesn't work with the "unknown" IP connection setup.

View 6 Replies View Related

Routers / Switches :: Seeing Allowed Connections From Blocked Servers?

Jun 23, 2012

Does the Host file allow connections to your computer?Although I have placed some server names into the host file, Wallwatcher 5.0 is indicating that those servers have made connections. This didn't seem to be a problem before I took some online advice to add servers to my host file. I use iptables on a WNDR3700 router with DD-WRT firmware. In the iptable rules I've also blocked these servers. One example is cnbc7.net and a couple of U.S. Akamai servers.

View 7 Replies View Related

Belkin Routers :: How Many Simultaneous Connections Does The AC1200 Support

Nov 5, 2012

I bought this router to temporarily replace my firewall while I wait for it to be replaced. We have a training center that when running full tilt, we probably have 50 devices trying to get on the internet.

View 1 Replies View Related

Belkin Routers :: F5D7634-4 V2 - No UDP Bittorent Connections Despite Enabling TCP & UDP?

Apr 29, 2013

I have a Belkin F5D7634-4 v2 (01) and when using bittorrent I cannot enable udp connections. In Virtual Server, both TCP and UDP are enabled - why won't it connect?

View 3 Replies View Related

Cisco Routers :: WRVS4400N IPS Blocks TeamViewer V7 Connections?

Jan 10, 2012

Since the change from TeamViewer 6.x to TeamViewer 7.x my router's (WRVS4400N V1.1, latest firmware V1.1.13-ETSI from 2009-02-24 and latest IPS definitions 1.50 from 2011-08-09) IPS blocks its connections to my remotely supported computers claiming a "P2P Vagaa connection attempt - 2". This is not happening with TV 6.x.Who does the error, TeamViewer or Cisco?

View 4 Replies View Related

Cisco Routers :: RV220w Configure For Ipsec Vpn Connections

Jan 2, 2013

I have an RV220w in office, which I have configure it for ipsec vpn connections. Behind router there is a NAS for file storage. [code]I have managed to connect to router from my home with ShrewVPN and I can ping every client connected to RV220w.The problem is that I can't connect to neither to router's web interface nor to NAS web interface or any other intranet web page ( the browser doesn't give any error, but keeps loading without showing the web page). Although, I can access web pages from my laptop.Also, in windows file explorer when I connect to NAS, although I can browse folders I can't copy files from my laptop to NAS and vice versa, I always get timeout error (I have checked the permissions to NAS and in addition I succeed to copy a small txt file 1kb, but no luck with bigger files).I also tried with QuickVPN client, but I had the same results. When I connect with pptp from windows everything works like a charm.My laptop has windows 7 64bit.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved