Routers / Switches :: Increasing Connections And Security?

Jan 24, 2012

I'm not sure about my title, it;'s the best I could come up with. I have approximately 7 computers, two iPhone, and iPad, wireless printers and a network attached storage. Most are connected over via wifi, the exceptions being one pc, the nas and a printer. I plan to add six more devices plus some ip cams. The way the router or network is configured whenever a guest connects to our wifi they can "see" our computers. I haven't been able to tell if they can see the files or just the name of the computer. Question 1: How can I tell if the guests are able to access the data on our computers or networked drive? Question 2: If I add a switch will I need to do anything special with regard to security?

View 1 Replies


ADVERTISEMENT

Routers / Switches :: How To Change WPA Security To WEP Security

Aug 22, 2011

my router has a WPA security system and I want it to be a WEP security system, what must i do?

View 7 Replies View Related

Routers / Switches :: How To Secure Network Connections

Oct 2, 2011

My itty bitty manual just shows on how to hook up my router via cable modem...nothing on how to secure it. I go into setup of the router and see where one can add info but am at a loss what to enter. I tried, merely by guessing, applied the info, and screwed up my networking. I couldn't even get into my router to revert back, cause i couldn't get on line...finally i reset manually my router and all is well again, except when i see a list of nearby network users, mine is the only one that says unsecured.

View 25 Replies View Related

Routers / Switches :: How To Connect 3 Outside Connections And Route Them Properly

Jul 19, 2012

We are planning 3 Internet Connections into our building. 1 will be for actual Internet traffic, 2nd for Voip phone system, and 3rd for internal network for Active Directory...etc. Oh the AD servers are controlled by another business so technically this line is still considered and outside line and is a T1. What I need to know is how best to make this all work so that our internet phones use the VOIP system, computers can log into the domain and access that network but use the Internet network for actual internet traffic? We were considering a series of managed switches and creating 3 VLAN's but I'm thinking we instead need a new router that all 3 networks connect to and dishes out DHCP to computers and phonesn example network is below.192.168.1.x ----> Internet (all computers use for internet traffic)72.10.10.x ----> VOIP (All physical and software phones use this network)10.10.10.x -----> Connection to external company that controls our network and has domain controllers, mainframe...etc.

View 2 Replies View Related

Routers / Switches :: Seeing Allowed Connections From Blocked Servers?

Jun 23, 2012

Does the Host file allow connections to your computer?Although I have placed some server names into the host file, Wallwatcher 5.0 is indicating that those servers have made connections. This didn't seem to be a problem before I took some online advice to add servers to my host file. I use iptables on a WNDR3700 router with DD-WRT firmware. In the iptable rules I've also blocked these servers. One example is cnbc7.net and a couple of U.S. Akamai servers.

View 7 Replies View Related

Routers / Switches :: Wireless Connections Will Only Allow One Computer At A Time?

May 24, 2012

Had laptop connecting wirelessly perfect with no problems. We then added another laptop and PSP 3 to the house hold. Any of the 3 devices will connect to the internet via wireless but ONLY one at a time. If you are connected with one and turn on one of the others it will kick the one off that you were on and only 1 device can use wireless at a time?

View 4 Replies View Related

Routers / Switches :: 192.168.01 Security Set-up?

May 20, 2011

I want a secure network and i have a netgear routor

View 1 Replies View Related

Routers / Switches :: How To Set Up Security For Linksys Router

Nov 29, 2012

I typed in my web browser 192.168.1.1 and comes up user name and password. after I type in Admin and admin kicks me back out to user name and password. I have reset the router per instructions and still doesn't work.

View 6 Replies View Related

Routers / Switches :: Can't Access Security Cameras From The Net

Aug 13, 2012

can't forward port 80 and 9000 from my Qsee Dvr on my linksys router. Model Bfsr41 firmware ver 1.05.03. I want to be able to access my security cameras remotely.

View 1 Replies View Related

Routers / Switches :: How To Get A Security Code For Netgear Router

Jul 10, 2012

How can I get a new security code? I never put it in when I brought my router because I lost the instruction paper.

View 3 Replies View Related

Routers / Switches :: How To Find The Network Security Key To Internet Modem

Jan 12, 2012

How do I find my network security key for my cisco e1000 router if the computer that it is installed on is broken?

View 1 Replies View Related

Cisco Security :: PIX 535 Maximum Connections

Jul 5, 2011

We have a PIX 535 with unlimited lisence, it has 1,048,953 in use connections because the timeouts have been changed to 24 hour. I am addressing this issue but was wondering why its so high when the max concurrent sessions is supposed to be 500,000 as listed in the product spec. Also when it reaches it max and cannot allocate a connection what PIX syslog error message number would it send?

View 1 Replies View Related

Network TCP Connections Attempted By Service Files - Security Risk?

Mar 10, 2012

My AV often reports my windows 7 ultimate 64 service files, such as winmon.exe or or service.exe requesting opened TCP connections along with a number of .DLL filkes, and then times they are flagged as heuristic behavior modification, however i know many of those are undeletable, due to windows security replacing them as soon as they are noticed to be missing and in another thread it was also indicated that these must be deleted from three places at once almost to actually prevent those from being instantly replaced, this explains maybe why i get this repeatedly immediately after boot up, but after five or some times it slows down to now and then.still quite a hassle to stop on start up.

View 2 Replies View Related

Cisco Security :: ASA 5510 - Internet Connections Dedicated VPN Traffic

May 22, 2011

We have an ASA5510 and we're currently using 1 internet connection to handle our site-to-site VPN connection and our internet traffic. We have a second internet connection on hand. What we would like to do it use BOTH internet connections: (1) will be dedicated to our VPN connection, (1) will be handling all our internet traffic. How can we get this setup? We're running Software Version 8.4(1)

View 1 Replies View Related

Cisco Routers :: RVS4000 - Multiple Internet Connections / Routers Sharing Printers?

Sep 11, 2011

I have 2 internet connections in my office one via Verizon Fios and another  one via the local cable company. On the fios connection I have an RV042 VPN  router and on the Cable company connection I have an rvs4000 router, I would  like to know if there is a way I can connect the 2 so I can share a printer I  have on one of the 2 networks from the other network without using the VPN  feature, like via an ethernet cable connected between the 2 and some kind of  static route maybe?

View 6 Replies View Related

Security / Firewalls :: Review Incoming Remote Desktop Connections Historically?

Apr 20, 2013

I was at my computer when the desktop appearance and taskbar changed. I immediately opened task manager to see what program might have caused this and didn't see anything out of the ordinary. Then about 2 minutes later my desktop changed back to what it normally is. I then went and disabled remote desktop connections... I think that someone may have accessed my pc remotely, buy I wasn't able to catch them at it. Is there any way to review incoming remote desktop connections historically?

View 3 Replies View Related

Cisco Switches :: SG300 And Multiple WAN Connections?

Apr 8, 2013

Currently I have my SG300 connected to a Wireless Router which is, in turn, connected to a Cable Modem.
 
I'm considering adding a second cable modem. Can the SG300 handle that?

View 3 Replies View Related

Cisco Switches :: SG-200 / SG-300 - 2 Internet Connections VLans

Apr 12, 2013

At the moment i have 2 internetconnentions with 2 different modems/routers. The computers are currently direct connected to the router.I'm considering adding a switch in the network and i hope i can make 2 different vlans each for one internet connection. The two networks should not be able to connect eachother.But i dont know what switch i need to do that. Do i need a Sg-200 or a SG-300 switch?

View 1 Replies View Related

Cisco Switches :: SD2008 Switch Drops Connections

Dec 12, 2012

My sd2008 switch keeps dropping the connection. If I replace the sd2008 with another switch it works without an issue. this switch has a limited lifetime warrenty. If true, can I return this switch for a replacement? The switch has firmware version 2.1 and the serial number is really hard to make out on the bottom of the unit. My sd2008 switch keeps dropping the connection. If I replace the sd2008 with another switch it works without an issue. Will this switch has a limited lifetime warrenty. If true, can I return this switch for a replacement? The switch has firmware version 2.1 and the serial number is really hard to make out on the bottom of the unit.

View 1 Replies View Related

Cisco Switches :: Bring Two Router Connections Into A SG200-50?

Apr 24, 2013

We have two Comcast 100MB routers. Can I plug these both into the SG200-50? How do I configure the ports?
 
I have an Apple Extreme Wireless Router that 30 Laptops use. I also have 25 VOIP phones and 10 Desktops that are on an unmanaged switch which I want to convert to the new SG200-50.

View 4 Replies View Related

Cisco Switches :: SG500X-24 Stacking - Keeping Connections Active

May 12, 2013

I am installing a network that has two SG500X-24 switches as core and several SG300-52 switches as access switches. I've seen in the SG500X-24 datasheet that there is a True Stacking feature. But in the data sheet there are not a lot of details about it. My doubt is the following. If I configure the two SG500X-24 switches as a single switch through stacking them, can I connect one SG300-52 switch to these two SG500X-24 switches through two cables (both configured as a LAG in the SG300-52 and in the SG500X-24 stack, one cable per SG500X-24), the  the first cable connected to the first SG500X-24 switch and the second cable connected to the second SG500X-24 switch and keep both connections active?

View 3 Replies View Related

Linksys Wired Router :: E2000 - Security Wired Ethernet Connections

Sep 19, 2011

I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive.  I am planning to allow a tenant in another building connect via an ethernet cable connected to my router.  Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router?  I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.

View 1 Replies View Related

Routers / Switches :: Setup An Home Network With A Wireless Router And Use Multiple Switches?

Jan 29, 2011

I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.

View 3 Replies View Related

Routers / Switches :: Connect 2 Subnets With Two Switches And One Router Using SIM Software?

Apr 23, 2011

how to connect two subnets with two switches and one router using router sim software?

View 1 Replies View Related

Increasing Ip Address Range?

Dec 24, 2012

I have an IPAD, pc , laptop, mobile and my daughter comes over with her ipod and mobile.As I understand things my IP address range is not big enough and as a result my IPAD keeps dropping and saying not connected

View 14 Replies View Related

Reasons For Increasing Bandwidth

Aug 31, 2012

what are the factors leading to bandwidth increase

View 2 Replies View Related

Routers / Switches :: Daisy Chain 3 Switches And Not Have Ip Conflict?

Jan 31, 2011

Is it possible to daisy chain 3 switches and not have ip conflict? I am running a public access network for a library. For certain library software I need for all workstations to see each other. I have 25 workstations in total and two separate management consoles. I have all workstations on two switches but one of the management consoles is on the third switch because when joined with the others it has an ip conflict. I need this console for the digital sender that is connected as well as to act as a server for go print software.

View 3 Replies View Related

Difference Between Wired Connections And Wireless - Routers

Feb 6, 2012

I see 350 and 450 Mbps speeds Router but I think that that only refers to wireless. Are there differences in the speed of a wired connection for all these new routers or are they all the same?

View 7 Replies View Related

Cisco Routers :: Rv180 Dropping LAN Connections?

Mar 13, 2013

I just recieved a new RV180 yesterday and it will not connect to my switch. Router was updated to the newest firmware, reset to factory settings. I did change the ip and ip range. Router works fine with one computer attached direct. As soon as I connect my sf300-24P to it, the WAN and LAN lights all light up and then go out. Only the WAN will light back up. I have no connectivity to the router. I plug the laptop to the router directly and no LAN lights come on and can not see the router with arp -a.

View 6 Replies View Related

Cisco Routers :: RVS-4000 Dropping Ip Connections

Apr 25, 2012

I have my RVS-4000 configured using static IP addresses in the LAN configuration.  The users use DHCP to get their addresses (for the most part, a couple may have static IPs set on the computer). I have the maximum number of DHCP users set to 1 to restrict the ability of people to log in to the system. That one address is locked down.
 
The internal address of the router is set to 182.168.2.1.  It doesn't conflict with anything on my network. I have 35 static IPs. About half of them are uing IP Based ACL to limit their access time but that doesn't seem to bear any relationship to what drops off.  
 
Almost daily one or more of the users will lose their IP address and a hard reset of the router is required.  The user this happens to seems random and it may be more than one but seldom all of them.  The network includes Windows7 (Home & Pro), a FreeNAS, Macs (Leopard and Snow Leopard), iPad, iPods, an iPhone and an AirPort Extreme used as a WAP (DHCP is disabled).  The AirPort is plugged directly into the router and has a staic ip on the RVS-4000 but is set to DHCP.  It seems to be the most common problem child.

View 3 Replies View Related

Cisco Routers :: RV215W Not Responding To Outside Connections?

May 5, 2013

The RV215W is not responding to the https port, the VNC port 5900 is also failing to respond. VPN still works, I will go in and reboot and it will work again. It works for 1 day and fails to connect again.
 
Latest Firmware is already install, I don't know what else to do.

View 2 Replies View Related

Cisco Routers :: WAP4410 Dropping Connections

Aug 10, 2011

Model: WAP4410N-A V02
Firmware version: 2.0.3.3
 
Deployed 3 of these as WAPs. No repeaters. They are spaced at least 50 feet apart over three offices, each in a server or switch room.
 
Across multiple laptops, and multiple WAPS, the wireless will function fine for a while with good bandwidth..then the connection will simply drop. By simply resetting the connection on the laptop or turning the wireless off then on, the connection typically returns, at least for a period of time before it drops again.
 
I’ve tried these configured as three separate SSIDs on identical channels, as well as one SSID for all three with different channels (preferred for a seamless wireless), and the behavior does not change either way.Based on some other threads, I tried forcing the LAN port speed to 100 mbps, but the problem persists.

View 7 Replies View Related

Cisco Routers :: RV042G Dual WAN Connections?

Jun 5, 2013

We are connecting to a Cisco DPC3825 cable modem supplied by our ISP.  It has been configured to act as a switch only.  They have supplied us with 2 static IP addresses.
 
When each WAN port is connected individually, everything is fine.  I see the IP addresses on the respective WAN port, and it is working fine.
 
When I connect both WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes completely non-responsive through its web interface.
 
How do I get the RV042G working with both WAN ports connected?

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved