I was following a guide to install optware on my DD-WRT router but I couldn't get the drive mounted. It is a memory card (with USB adapter) with two partitions, both EXT3, one is 1gb and the other one is 13.65GB(ish). Here is my startup command:
[/QUOTE]mkdir /tmp/etc/config
echo "wget [URL]" >> /tmp/etc/config/fs.wanup
[Code].....
I was under the impression that the AIR-CAP3502I-E-K9 is a ceiling mount AP only. Is any one using these as wall monuted AP's?
View 5 Replies View RelatedSG 300-10 user manual states to not mount the switch on either side (I'm assuming this means the right or left ends as you face the front) and that they can be mounted either face-up or face down or flat). The specs further say that a 5" space must be "around all sides" of the unit. Silly question is what does "all sides of the unit' really mean? (of course given you must mount is somewhere). Also, given the little feet supplied with the unit, it is implicit to me the bottom needs to be only about 1/32" from the horizontal surface it is placed on. If this is true, can this unit be mounted face down on a shelf such as the Leviton 47612-UBK (it's allowing the mounted units to have airflow between the unit and the cabinet back) and have a second SG 300-10 mounted in front of the first that is seperated from the first by either the dual feet or use separation spacers that will fill the available shelf space and maximize the distance between the units - all without degrading the inherent reliability of either?
Lastly, The two SG 300-10's are reaching the internet through a LINKSYS E4200 router. Is it better to have each SG 300-10 occupying its own dedicated port on the router OR to cascade one SG 300-10 to the other SG 300-10 then one of the LINKSYS E4200 router? If the answer is each occupying their own dedicated LINKSYS port, then would it be prudent to load one SG 300-10 with the most active ethernet lines to allow the other SG 300's port power management to shut it down?
if the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket? I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.
View 4 Replies View RelatedHow to mount the E4200 on a wall. Any smart ways to do it?
View 9 Replies View Related mounting for the above antenna types. see figures below.
The figures above, are the antenna mounting correct? For figure 1, can the two antennas be separated by 4" or more? For figure 2, the two antennas will be side by side.
I need some manual about how to use AIR-ACCRMK1300=.Is there any offical manual?
View 4 Replies View RelatedWe have a campus with both office and industial areas with various propagation problems. Historically I have been installing and maintaining access points in the 1200 range, the latest being the 1242. All these have a similar antenna setup based on diversity pairs.Since Cisco seems to be dropping the old series any week now I have been looking at the 2602 as a replacement.I can find no good documentation on antenna selection and mounting suggestions for these.If I want a proper omni coverage pattern with dual band antennas, do I just set them to a H form assuming the unit is sitting on a wall?
View 1 Replies View Relatedi want to know, is c3650G or c3650X switches are already containing rack mounting pack or am i need to buy it seperatly?
View 3 Replies View Relatedmounting 3500i access points (AP) to the ceiling ...The ceiling is an Armstrong suspended ceiling with 24" mineral fiber drop ceiling..What are recommendations and best practice - mount AP under or above the ceiling? Initially, I considered the mounting options from Oberon Inc. (p/n :1064-00), but given the difficulty by purchasing this product in my country have to consider other options..I must say that the decision to mount the access point to the ceiling like this:
Now I looking a version of the mount АP with flush-mount kit for tiled ceilings (AIR-AP-BRACKET-3=)..
it seams, that the mounting blade for the 1142 access point and the 2602 access point are identical.
We have ordered the new 2602 with internal antennas for deploying WLAN in a new building, but I never hold this accesspoint in my hands. We have a few mounting blades in spare from the 1142 accesspoint. The question is, can I prepare the mounting of the 2602 access point with the 1142 mounting blade?
I've got a number of 3502i's that I need to mount in a new classroom that does not have any ceiling (except the floor decking above). Ceiling is roughly 30-50' up. Contractors are going to run several 2" (or whatever we want) metal pipes from the ceiling down to a more reasonable level to mount the access points on and get below the hvac ducts/etc in the ceiling.
Problem is I can't find any bracket or mounting options for this! What are others using in this situation for mounting one of these access points onto a metal pipe such as this? I've checked Oberon Wireless, Terrawave and I don't see anything glancing through the product catalogs. Anyone mounting access points this way?
I have realized that E4200 V1 I have, with 1.03 firmware, seems to be dying when I reboot it and it tries to load the USB HD I have connected to it. By die I mean the web server does not work anymore (http://192.168.1.1), and new computers can't connect to the router. I suspect it is due to the amount of files I have in the External Disk Drive -I used to have Media Server enabled, but I disabled it because this problem was happening, and I only left File Server enabled. Now since I moved many of my pictures to it, it seems even File Server is causing problems, and if neither one work for me, then this router does not justify its money, since that was the only reason I bought this E4200 hardware. These problems are solved in V2? Since it is still under warranty, I could try to exchange my V1 for a V2 version.
View 3 Replies View RelatedI just bought an e4200 with firmware version 2.0.36 from Costco.I have set it up manually and have access to the internet for all of my wired and wireless devices.Unfortunately, I cannot access the USB storage via mounting a share, the media server or the FTP server. I have plugged in a USB storage device that is formatted with FAT32. The router detects it and allows me to create new shares in the Storage->Disk menu and Storage->Media Server menu - so I know it can read the device and see the folders. Strangely if I click "Scan All" in the Media Server, it finishes very quickly and never updates the "Last scanning time" field.There was a brief moment when the router showed up in the Network->Computer section of File Explorer, but I can't get it to show here again.
View 8 Replies View RelatedNot sure why Cisco is shipping like this? It is a pain to mount them. Earlier we had option to slide out the Secuirty hasp.
View 1 Replies View RelatedMy mechanical engineer needs detailed measurements for the hole patterns on the sides of the Cisco 2911. Where I could find this?
I've searched and read the installation docs, which shows pictures of the units. Although useful, they does not show exact measurements, angles, and hole diameters.
