This is one I am having a hard time finding an answer for. How many clients can a 3600 AP support? For 150 clients on one of these, what would the throughput be for each client?
If my calculations are correct, the device can deliver 420 Mbps, which gives each client roughly 2.8Mbps. Is this correct?
What the maximum concurrent users you can have on a Cisco 3925 for :-
1) Site to Site VPN using IPSEC tunnels
2) GRE tunnel sIf I have 90 users on a single GRE tunnel with 50mb Internet pipe using fat clients will this work ?
We have a client that is looking to provide connectivity for up to 800 users at a conference. They have a SRP527W available to them. Looking at the configuration we have been able to provide the needed number of IP addresses through VLANs each with their own DHCP scope.
However we are doubtful that the router will be able to process such a high number of connections (NAT, Firewall etc.) even though they will be using a specialised application that pulls static content via WAN.
Thus far we have been told that the unit has supported 150 user no issue, my I am guessing anything over 200 and you would start to see stability issues?
I'm using a Huawei B660 3G router at my house, with with a service provider called 8ta (in South Africa). I've been struggling for months to try and get them to troubleshoot and fix my connection, which was working fine for about a year.
I'm now daily struggling with download speeds of as little as 0.1Mbps to 0.5Mbps, especially after 5pm until about midnight. Upload speed off course is even worse.
8ta, has after months of me complaining agreed to install an antenna at my house, which will probably take another few more weeks for them to accomplish.
I often have 5/5 bars of signal on the router, so my argument is that signal strength might not be the problem. Since the connection is in a residential area, I would assume that their network is more likely to be a bit more congested after hours, but a technician explained to me that their network is never more than 30% "occupied".
Can the number of users connected on the 3G network/tower cause signal strength to attenuate for surrounding users?
Would it replace the B660 (7Mbps) router with a 21Mbps counterpart?
Getting the following alarm from my ISE:Cause:Base License Enforcement Details: Base concurrent users exceed license allowable count.Currently only using 1656 out of 2000 base licenses so I'm not sure what the issue is. Running 1.1.2.145 patch 3.
View 1 Replies View Relatedtrying to join an 1142 on a WLC_SRE version 7.4.
the AP can ping the controller and vice versa. In the controllers GUI: Monitor>Statisticc>AP join, I can find the mac of the AP that I am trying to get joined.
the details of this mac show:
Last error occurred: Lwapp discovery request rejected
last occurred error reason: Too many concurrent AP image downloads
Last Join Timestamp:
Was looking at purchasing WAP321 however after looking at the spec's I see it has not got concurrent dual band (2.45Ghz/5Ghz) is there any simular access points with dual band and captive portal?
View 2 Replies View RelatedWhat is the maximum number concurrent wireless connections that a WAP54g v3 can have?
View 9 Replies View RelatedI got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
URL
Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
View 13 Replies View Relatedif the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket? I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.
View 4 Replies View RelatedI am not having much luck getting it converted via normal ways.
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing).
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar 1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..' Even if I set a static IP address.
Is there way to disable the join process while I upgrade the software? I guess fire up a controller for it to join. I hope I don't have to have a controller to convert these.
I have an AP group on a Cisco 5508 WLAN controller. Currently, it is populated with 13 Cisco 1142 lightweight access points. When I try to add a Cisco 3602i access point to the group, I get the following error in NCS: Error: OfficeExtend requires primary, secondary, or tertiary controller management IP to be set.I am using DNS to allow my AP's to find the controller and they work just fine. Is there a reason I can't add the 3600 series AP's to the AP group?
View 13 Replies View Relatedi'm going to upgrade a 5508 wlc code from 7.0.116.0 to 7.1.91.0 to add 3600 series access points having it all manageable via WCS ver 7.0.230.0 it seems to be possible, as it is explained in the compatibility matrix found on [URL]now I have to download the file to the controller...
AIR-CT5500-K9-SPECIAL-7-1-91-0.aes
(direct update possible)
before doing that I'd like to know if I will loose my configuration on the controller i'm concerned about that because the release document is not clear:
- We highly recommend that you back up your controller's configuration files prior to upgrading the controller software. Otherwise, you must manually reconfigure the controller.
- For busy networks, controllers on high utilization, or small controller platforms it is advisable to disable the 802.11a/b/g networks as a precautionary measure.
- Step 5 Disable any WLANs on the controller.
- Step 19 Re-enable the WLANs......
- Step 22 If desired, reload your latest configuration file to the controller. (reload config after reenabling wlans?another controller another question .....: a cisco wlc 2100
found 2 update files
AIR-WLC2100-K9-7-0-230-0-ER.aes
AIR-WLC2100-K9-7-0-230-0.aes
why 2 update files this time? what file to update first?
I´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies View RelatedI have a 5508 controller with a bunch of 3600 Series APs. I did all the basic config on the controller and added all the APs through distribution port #1. Now I was trying to config a second interface ( port #2) and use it for the Guest SSID on a separate VLAN. After I rebooted the controller, it dumped all the APs. I would like to know if this is normal, If I need to enroll the APs everytime I reboot the controller.
View 1 Replies View RelatedI have to prepare an 3600 Capwap AP for autonomous functionality!
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:
• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?
I want to use the flexconnect in the same network where the wlc is located. Normally we will do it for over WAN and branch office. But I want to use in the same main office to avoid more bandwidth utilization on my distribution layer. Wlc is connected on Distribution switch.I want to do local switching in the access layer switch.
The below is the sample topology. But real topology contains nearly 200 AP's(3600 series) and 20 access switches and so on.....So there is a chance of 200 AP * 350 Mbps can flow on the distribution layer.So ,
1)If I use flexconnect any issues will be occuring?
2)Does it cause any impact on VOWLAN?
I have two ASA5510 each with a security plus license and 10 SSL VPN licenses, in active/standby mode at version 8.4(4)1. It only allows up to two vpn clients (AnyConnect & SSL VPN) at a time, any extra vpn client would receieve "Login Failed" message.
View 2 Replies View RelatedI am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
I am don't need anything unusual and I would love to go with the 2600/3600 APs, unless mixing them up is a problem.
View 2 Replies View RelatedI am looking for the Maximum Power Settings Spec for the 3600 AP. The one from 2008 is too old. Does an update exist? The AP Spec itself does not show power levels by channel and regulatory domain which is what I need. If I can't get the spec, I will have to query the AP using "show ap config 802.11x apname" for each config I need.
View 1 Replies View RelatedLost my access points to controller. Not sure if it was related to upgrade from 7.1 to 7.2, or something else.
The console log on APs shows;
*Mar 1 00:01:09.394: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 1 10:24:23.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 142.100.64.8 peer_port: 5246
*Jan 1 10:24:23.424: %DTLS-5-ALERT: Received FATAL : Certificate unknown alert from 142.100.64.8
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Bad certificate alert received from peer.
*Jan 1 10:24:23.424: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 142.100.64.8:5246
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
All 3500/3600 APs, had been in production for months.
I've got a client who purchased numerous 3600 series AP's (3602i to be exact) and would like to add them into their WLAN 4404 controller. They're currently on 5.x system code so I plan on getting them upgraded to the latest 7 code.
They currently have a number of AP's adding and working fine. Once the WLAN controller is upgraded, does anything specific need to be done within the WLAN gui to add in these new 3600 series AP's?
i have cisco wlc 2504 connected with cisco 3600 ap,now the customer required n bandwidth speed ,but in wlc am not able to enable n bandwidth for ssid.in radio policy of ssid also n bandwidth is not showing,only this bandwidth showing a/g,g,b/g, and all?
View 8 Replies View RelatedCustomer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies View RelatedDoes cisco 3600 support office extend feature? If yes, is there a controller requirement? I know cisco AP 600 supports office extend
View 24 Replies View RelatedAironet 2600 and 3600 series. I need to know their maximum distance (at least theoretically, in Line of sight, eliminating all other factors...) in order to choose the right number of AP to provide enough coverage for a specific area. If an exact number is not available then can you show me how to determine it?
View 8 Replies View RelatedWe have an MPLS (layer 3) network 4 offices and a Data center. We are planning to install about 10 Access Points(3600 series) per office and have a controller(5508 series) in the Data center.
Questions:
1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Data center?
2- We would like to accomplish this in two phases:
A- install access points without controller handling authentication thru Microsoft IAS servers (current configuration with 1200 series)
B- Deploy wireless Controller in Data center and start migrating orphan AP to Controllers one office at a time.
I am currently planning a Active directory deployment. It will most likely be a new forest, but the domain could become part of a existing forest. I have about 45 Computers with about 85 users. At one time there is about 42 users logging in as there is two shifts. The logons will be done all at once. Do you think two domain controllers will be able to handle the load?
View 9 Replies View RelatedWe are having random issues of users not being able to connect to our wireless network consistently. The users will have successfully accessed the network previously but then will have difficulty associating to the network. After a period of time, the association appears successful again. My first thoughts were that there was a restriction on the number of clients that could associate to a given AP at any one time.This is the equipment we have:1x Cisco Wireless Control Server (WCS) 6.0.181.04x Cisco 5508 Wireless LAN Controllers 6.0.196.060x Aironet 1142N Lightweight Access Points (LAP) Is there a hard or recommended maximum number of clients per LAP? If so, where is this defined? From what I have read on these forums, Cisco apparently recommends about 25 clients per AP but I can not find any official documentation to support this.When I go to WCS Home > General > Top APs by Client Count, the top AP reports 20 clients. However, if I click on the AP Name and go to the Current Associated Clients tab, it is only listing 8 clients - why is this?
View 3 Replies View RelatedWe have a PIX 501 and I'm in the process of replacing it with a ASA5505. We're currently using the 501 for a site-to-site vpn for disaster recovery purposes and I'm trying to verify the number of concurrent connections we can have.
View 1 Replies View RelatedI have been looking for the command to view all concurrent active connections or sessions on our Cisco 2911. I want to see what the total connections or sessions are at peak times throughout the day.
View 4 Replies View Related