What the maximum concurrent users you can have on a Cisco 3925 for :-
1) Site to Site VPN using IPSEC tunnels
2) GRE tunnel sIf I have 90 users on a single GRE tunnel with 50mb Internet pipe using fat clients will this work ?
We have a client that is looking to provide connectivity for up to 800 users at a conference. They have a SRP527W available to them. Looking at the configuration we have been able to provide the needed number of IP addresses through VLANs each with their own DHCP scope.
However we are doubtful that the router will be able to process such a high number of connections (NAT, Firewall etc.) even though they will be using a specialised application that pulls static content via WAN.
Thus far we have been told that the unit has supported 150 user no issue, my I am guessing anything over 200 and you would start to see stability issues?
We are having random issues of users not being able to connect to our wireless network consistently. The users will have successfully accessed the network previously but then will have difficulty associating to the network. After a period of time, the association appears successful again. My first thoughts were that there was a restriction on the number of clients that could associate to a given AP at any one time.This is the equipment we have:1x Cisco Wireless Control Server (WCS) 6.0.181.04x Cisco 5508 Wireless LAN Controllers 6.0.196.060x Aironet 1142N Lightweight Access Points (LAP) Is there a hard or recommended maximum number of clients per LAP? If so, where is this defined? From what I have read on these forums, Cisco apparently recommends about 25 clients per AP but I can not find any official documentation to support this.When I go to WCS Home > General > Top APs by Client Count, the top AP reports 20 clients. However, if I click on the AP Name and go to the Current Associated Clients tab, it is only listing 8 clients - why is this?
View 3 Replies View Relatedi am going to purchase a Simultaneous Dual Band Router with Gigabit Lan. Can anybody tell me whats the transfer speed it got on Concurrent Dual Band 900(450+450) , 750(300+450) and 600(300+300). I am going to use it for hard drive that can network attached or may be just external hard drive via USB interface.
View 2 Replies View RelatedWhat is the maximum number concurrent wireless connections that a WAP54g v3 can have?
View 9 Replies View RelatedThis is one I am having a hard time finding an answer for. How many clients can a 3600 AP support? For 150 clients on one of these, what would the throughput be for each client?
If my calculations are correct, the device can deliver 420 Mbps, which gives each client roughly 2.8Mbps. Is this correct?
I'm using a Huawei B660 3G router at my house, with with a service provider called 8ta (in South Africa). I've been struggling for months to try and get them to troubleshoot and fix my connection, which was working fine for about a year.
I'm now daily struggling with download speeds of as little as 0.1Mbps to 0.5Mbps, especially after 5pm until about midnight. Upload speed off course is even worse.
8ta, has after months of me complaining agreed to install an antenna at my house, which will probably take another few more weeks for them to accomplish.
I often have 5/5 bars of signal on the router, so my argument is that signal strength might not be the problem. Since the connection is in a residential area, I would assume that their network is more likely to be a bit more congested after hours, but a technician explained to me that their network is never more than 30% "occupied".
Can the number of users connected on the 3G network/tower cause signal strength to attenuate for surrounding users?
Would it replace the B660 (7Mbps) router with a 21Mbps counterpart?
Getting the following alarm from my ISE:Cause:Base License Enforcement Details: Base concurrent users exceed license allowable count.Currently only using 1656 out of 2000 base licenses so I'm not sure what the issue is. Running 1.1.2.145 patch 3.
View 1 Replies View RelatedI have 2 questions about the Cisco Air-CAP3502I-A-K9.What is the recommended and maximum number of conncurrent users this device supports?What is the recommended and maximum range of this device? I've looked else where but can't seem to get any hard numbers.
View 5 Replies View RelatedI wanted to know if anyone can say with certainty how many clients can stay connected 'Aironet 1140 series. I state that I should connect WiFi in about 350 clients.
View 6 Replies View RelatedI have two ASA5510 each with a security plus license and 10 SSL VPN licenses, in active/standby mode at version 8.4(4)1. It only allows up to two vpn clients (AnyConnect & SSL VPN) at a time, any extra vpn client would receieve "Login Failed" message.
View 2 Replies View RelatedI am currently planning a Active directory deployment. It will most likely be a new forest, but the domain could become part of a existing forest. I have about 45 Computers with about 85 users. At one time there is about 42 users logging in as there is two shifts. The logons will be done all at once. Do you think two domain controllers will be able to handle the load?
View 9 Replies View RelatedWe have a PIX 501 and I'm in the process of replacing it with a ASA5505. We're currently using the 501 for a site-to-site vpn for disaster recovery purposes and I'm trying to verify the number of concurrent connections we can have.
View 1 Replies View RelatedI have been looking for the command to view all concurrent active connections or sessions on our Cisco 2911. I want to see what the total connections or sessions are at peak times throughout the day.
View 4 Replies View RelatedWhat are the limitations on the max number of concurrent HTTPS connections when using Auth Proxy for HTTPS traffic on a Cisco ASA 5520.
1) What is the max number of concurrent Authentications that the ASA can perform (HTTPS)?
2) Once Authenticated. What is the max number of concurrent HTTPS Authenticated connections to the back end HTTPS server.
Our current cable ISP is having issues providing us with consistant connectivity. I would like to bring in a second ISP to allow my users to choose where they will connect to. There will be two dns names and i just want to to be able to choose between them.
Is this possible on the ASA5505? supporting two ISPs at one time for VPN on both?
in Cisco ASA 5540 Adaptive Security Appliance Platform Capabilities and Capacities, I see Concurrent Sessions: 400,000. Which mean what device can handle 400,000 session and no more. But if I'm using TCP State Bypass Feature (Inbound traffic pass via ASA but Outbound goes via different device). I can see such connections via show conn command with b flag.
My questions: 1. Will this limit (Concurrent Session) affect in this case? Or ASA can handle more such connections (for example 800,000 ...) in bypass state? 2. It's possible to tune timeout for such connection without using global timeout conn? My problem what I want to do by pass tcp connection for one IP with has very high connection/sec rate.
trying to join an 1142 on a WLC_SRE version 7.4.
the AP can ping the controller and vice versa. In the controllers GUI: Monitor>Statisticc>AP join, I can find the mac of the AP that I am trying to get joined.
the details of this mac show:
Last error occurred: Lwapp discovery request rejected
last occurred error reason: Too many concurrent AP image downloads
Last Join Timestamp:
how many concurrent voice call can be conducted at once with the cisco sf 100d-08 8-port 10100 switch?
View 1 Replies View RelatedWas looking at purchasing WAP321 however after looking at the spec's I see it has not got concurrent dual band (2.45Ghz/5Ghz) is there any simular access points with dual band and captive portal?
View 2 Replies View Relatedtell me if cisco 1921 onboard GigabitEthernets can reach 10Mbps with concurrent services, one GigabitEthernet interface as WAN interface, the other one as LAN interface.
View 2 Replies View RelatedI´m detecting on my ACE 20.
I´m monitoring the total number of concurrent sessions of my ACE 20 (using Cacti), and from time to time, with no discernable pattern, I see an instant drop of sessions to half...I don´t detect any disturbance with our traffic and service, I have no complaints, but it's a very accentuated drop.
I´m able to get 1 or 2 days withouth any suddent drop of connections, and then for no reason I pass from 500.000 to 200.000 sessions in a minute. Then they gradually go up again.
I´ve seen in ACE´s session table that she keeps a great number of half-open, or closed sessions, and those are counted as part of concurrent sessions. Is there any flush on ACE´s table when she reaches a certain number of closed TCP sessions or something like that?
I need 3925 router that support BGP as well as IPSEC VPN. is this correct part number i ordered? CISCO3925-SEC/K9. Its always hard to understand Cisco licensing, specially new one. will above package will have router wth ipbasek9+seck9?
View 4 Replies View RelatedI have a new 3925 ISR G2 router with the universal IOS, 256kb flash in CF0, 1gb flash in CF1. When the router boots it prompts to enter initial config. Whether I say yes or no, enter the appropriate info, "write memory", and reload it comes up with a blank config. I've checked the config-register (2142), copied the start up-config to nvram:, flash0:, and flash1: but nothing works.
View 2 Replies View RelatedI have one router 3925 equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
Please find the attached config details.
I have spend half day to look up this question in cisco official web site, but get nothing . Any infomation about vpn performance of 3925 router？Produce : cisco 3925 ( Cisco 3925 Security Bundle w/SEC license PAK )Question is , how much ipsec vpn tunnels can be carried as a vpn server of this bundle ? if more licenses may be bought, how much most tunnels can be held？
View 5 Replies View RelatedI have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
View 5 Replies View Relatedhow to setup natting on a 3925 router.
View 1 Replies View RelatedI have a question regarding the 3925 router. In the past on my old 3660's, in order to add a new line to an ACL, I would have to remove the entire ACL and readd it when adding new ACL lines to the list. Is this required on the 3925's, or is it like the ASA 5520's where you can just add an ACL any 'ol time without having to remove/add the entire ACL list?
View 2 Replies View Relatedwe are configuring a ras on 3925 router with e1 controller. when we connect the e1 controller to pbx we got on pbx a no frame alarm (detailed error is that we have nfas but we do not have cas). what could be the error? do the router need dsp to have a framed e1?
View 1 Replies View Relatedi said in the title i have forgot my password for my cisco3925 rourtor and how to reset my password
View 3 Replies View Relatedchecked all the recovery doc, however, there is no one specific for 3900 series router
View 2 Replies View RelatedI have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 Replies View Related