I have 2 questions about the Cisco Air-CAP3502I-A-K9.What is the recommended and maximum number of conncurrent users this device supports?What is the recommended and maximum range of this device? I've looked else where but can't seem to get any hard numbers.
View 5 RepliesI want to know what is the maximum range of WAP200E. I found in an overview of the family of access points "CISCO SMB" that could reach up 4kms. Is that true?
View 3 Replies View RelatedI wanted to know if anyone can say with certainty how many clients can stay connected 'Aironet 1140 series. I state that I should connect WiFi in about 350 clients.
View 6 Replies View Relatedwhat is the maxium range of a router?
View 3 Replies View RelatedWhat the maximum concurrent users you can have on a Cisco 3925 for :-
1) Site to Site VPN using IPSEC tunnels
2) GRE tunnel sIf I have 90 users on a single GRE tunnel with 50mb Internet pipe using fat clients will this work ?
We have a client that is looking to provide connectivity for up to 800 users at a conference. They have a SRP527W available to them. Looking at the configuration we have been able to provide the needed number of IP addresses through VLANs each with their own DHCP scope.
However we are doubtful that the router will be able to process such a high number of connections (NAT, Firewall etc.) even though they will be using a specialised application that pulls static content via WAN.
Thus far we have been told that the unit has supported 150 user no issue, my I am guessing anything over 200 and you would start to see stability issues?
what this syslog message means? Being getting this on my 3945e series routers. My gut tells me they are caused by our Security guys scanning my routers with invalid login attempts.
%SSH-3-DH_RANGE_FAIL: Client DH key range mismatch with maximum configured DH key on server
Is the max wireless speed on the cisco 881w 54mbps even though it has 802.11n hardware? What about the 891w ?
View 13 Replies View RelatedOn a 1602 autonomous AP in the US, should the maximum DB power level be 22DB or 17DB? According to the datasheet it shows 22DB when all 3 antennaes are in use although I am only showing 17DB as the allowed maximum even though all 3 are enabled.
Antenna: Rx[a b c ]
Tx[a b c ofdm all]
Internal
Gain [Allowed 8, Reported 0, Configured 0, In Use 8] (dBi x 2)
[Code]....
My question is about the maximum possible transmitting power in a Cisco 1242AG-E-K9.I did an update of my AP on a new ios version and since then, the maximum power for me is limited to 17 dbm. I check this within the console and the "show controllers dot11radio0 | include Power:" command. I thought that I had 20dbm before the update, but unfortunately I can't proof this by myself because I have no AP left with the old firmware.
Is it possible that the upgrade did this? I read about the regulatory domains for the transmitting power. I live in Switzerland, so I thought I could use 100mW if I want to. I read it's not possible to use the 100mW at each speed but I think I should stull be able to select the 20dbm/100mW or am I missing something?
I have been searching online for the maximum coverage (distance) of WAP4410N
View 1 Replies View RelatedI will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas. What is the maximum transmit power, 20dBm or 23dBm? I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.
View 4 Replies View RelatedWhat is the maximum theoretical distance with air-cap3602i-a-k9 with internal antenna?
View 5 Replies View RelatedDoes any body know what is the maximum of simultaneous connections that the AIR-LAP1131AG-E-K9 access point supports?
View 2 Replies View RelatedI have 1242AG. how many clients can be connected to this AP??
View 4 Replies View Relatedhow i can add maximum speed kbps for dialing modem
View 1 Replies View RelatedI have a BT Home Hub 3 and quite often get messages "cannot connect to network". I have many (>20) devices connected. Have I reached the limit? With four kids in the house the pressure to connect even more devices is growing.
View 1 Replies View RelatedOnly fifteen users are allowed to connect on the WLAN Controller WLANs provided on the 600 series at any one time. A sixteenth user cannot authenticate until one of the first clients de-authenticates or a timeout occurred on the controller. Note: This number is cumulative across the controller WLANs on the 600 series. For example, if two controller WLANs are configured and there are fifteen users on one of the WLANs, no users will be able to join the other WLAN on the 600 series at that time. This limit does not apply to the local private WLANs that the end user configures on the 600 series designed for personal use and clients connected on these private WLANs or on the wired ports do not affect these limits. This is from the Configuration Guide for teh 600 series Office Extend AP. Is this count per AP or total per WLC? If I have 10 APs deployed to our remote users, can each AP support two simultaneous users? Would I need to use separate WLANs for each OEAP?
View 8 Replies View RelatedI seem to only able to create a maximum of 16 WLAN SSIDs on WLC 2504.Can this be added through licensing or a software upgrade.
View 1 Replies View RelatedI have two Cisco Aironet 1310. I wonder which is the maximum distance I can put between them, to an acceptable data transmicion to 54 megabytes or less, using thier internals antennas.
View 2 Replies View RelatedIs there a limit to the number of ssid's that can be supported in h-reap mode? I need to deploy at least 4 but the documentation does not necessarily say. I'm deploying these ssid's on a 7500 controller.
View 1 Replies View RelatedI am looking for the Maximum Power Settings Spec for the 3600 AP. The one from 2008 is too old. Does an update exist? The AP Spec itself does not show power levels by channel and regulatory domain which is what I need. If I can't get the spec, I will have to query the AP using "show ap config 802.11x apname" for each config I need.
View 1 Replies View RelatedHow many maximum clients are supported by cisco aironet 1262 AP and also by a 5500 Wireless Controller?
View 4 Replies View Relatedwhat is the maximum speed of vpn connection (pptp, l2tp)?
View 2 Replies View RelatedIs this the best way to get maximum performance and coverage? I have a DIR-655 bridged to supply B/G on channel 11.I Gave Up On Linksys Firmware And Installed DD-WRT.
View 4 Replies View RelatedI have a question regarding to the maximmum number of active SSID's on a WLC 5500 with 3500i, it's my understanding that the 3500i can support 16 active SSID's is it the same when connected to the WLC? Also, if possible would the WLC shutdown un-used Radios or maybe after hours?
View 1 Replies View RelatedWe are about to upgrade our training facilities wireless and i have a few questions regarding the number of active clients we should target our design for.
We would be using 1142 and 3502I access points. I was thinking that based on the belo we'd be able to support around 30-40 clients per AP.
Protocol
Type of web use
Amount of bandwidth allocated per device
[Code]....
which is the maximum number of simultaneous wired guest clients on a 5508? And in a 2112 controller?
Wired clients count as wireless clients??
What about anchoring limitations, what is the effect of wired guest clients on the anchor controller?
I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.
Questions :
1. What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?
2. If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point
3. I there a simulator tool that can be used to simulate multiple wireless connections to an AP
4. Have anyone tested so many users connected to 1 Access point ?
What is the maximum distance or safe distance this antenna can cover. I am using Aironet2602E access point. Because i couldnt understand the radiation pattern. There is 5 circle in the Radiation pattern but i dont know how to convert this is distance. Its only showing the DB.
View 23 Replies View RelatedI have a deployment of AIR-CAP35021 APs. They are in 2 buildings with multiple floors. They are installed in a row down the hallways. I want to increase the power levels by using the controller and not configuring the APs individually. I have set the TPC value to -50 but I still do not reach the outer walls of the floors in some areas. I need to know what to set the Max Power Level Assignment or Min Power Level Assignment to to get the APs to power up some more. If the MAX value is 30 and the default is 30 then how to adjust that value?
View 5 Replies View RelatedWhat is maximum achievable speed of my e1200v1? Latest firmware is installed. I am using Xfinity Blast (50/10). Wired, i get 52mbps, wireless only 25mbps.I have attempted reflash, WMM disable trick, channel 9 setting and disabling the wireless security completely. Normally, i have my laptop, Droid3 and iPod connect via wireles, but for the sake of achieving max speed, i disabled all but the laptop. wireless connection status displays speed: 144 mbits.
View 9 Replies View RelatedWhat are the maximum number of AE2500 wireless adapters can be installed on a PC running Windows XP SP3 using the windows wireless zero configuration? Recently I'm working on a program that needs multiple seperate wireless connections on a Windows XP SP3 PC. Each wireless adaptor is given a static IP address to respond to traffic at some specific ports. I can install four AE2500 adaptors without problem, but it disconnects the first AE2500 device when I plug in the fifth AE2500 adapter. I've tried on different windows XP machines. They all get the same problem. I wonder if it is a limitation in the AE2500 driver.BTW I've also tried to install an Valet AM10 adaptor as the fifth adapter, it seems ok. Yet installing more AM10 adapters beyond the fifth (4 AE2500 + 1 AM10) requires some luck. It may disconnect the other AM10 devices when I plug in another AM10 adapter.
View 1 Replies View Related