On a 1602 autonomous AP in the US, should the maximum DB power level be 22DB or 17DB? According to the datasheet it shows 22DB when all 3 antennaes are in use although I am only showing 17DB as the allowed maximum even though all 3 are enabled.
Antenna: Rx[a b c ]
Tx[a b c ofdm all]
Internal
Gain [Allowed 8, Reported 0, Configured 0, In Use 8] (dBi x 2)
[Code]....
What would be the best option to monitor the load on AP live? Is there a GUI tool for this or should I use command line interface? I was hoping that CNA would do this, but the AIR-SAP1602I.EK9 does not seem to be supported by the CNA. CCP seems to be another application, would this do what I want?
View 1 Replies View RelatedI have successfully setup the Cisco 2504 (AIR-CT2504-K9).
Trying to add 2 Access Points (AIR-SAP1602I-A-K9). I created static IPs for both in the router (RV180). The Access Points are connected to the PoE ports on the Cisco Switch (SG200-08P). The 2504 is connect to one of the non-PoE ports on the SG200. The SG200 is then connected to another switch (SF302-8P), which is connected to the Router (RV180), which is connected to the cable modem (Cisco DCM3000).
I am able to ping both of the access points from within the LAN, but they do not show-up on the 2504 console.
AIR-SAP1602I is a Standalone AP (Fat-AP), can we convert it to Ctrlr-based AP(Thin-AP) via install another IOS ?!In contrast, can we convert AIR-CAP1602I to be a Standalone AP ?!
View 5 Replies View RelatedI am trying to have a setup where the AP running in autonomous mode also act dhcp server for the wireless clients.The only thing is that the vlan is switched across to the wired network.
So basically i am having 2 vlans, one for mgmt and other for data (for wireless clients) and both vlans are trunked to the switch.
[CODE]...
I want to buy an AIR-SAP1602I-E-K9 and I don't know if I can configure a MAC-BASED ACL with this AP, because I must permit the access of the wireless netwok only to determined wireless devices.
View 4 Replies View RelatedI have a question regarding to AIR-CAP3602I-A-K9. May I know does AIR-CAP3602I-A-K9 has the 802.11a module? Since I configured it with vWLC, I haven't AIR-CAP3602I-A-K9 inside 802.11a/n?
If so, any module I need to purchase to enable 5GHz.
vWLC version: 7.3.112.0 AIR-CAP3602I-A-K9 version: 7.3.112.0
I've read in some of the cisco documentation on the 1250 series that root bridge or non root bridge modes are "not tested". They don't say "not supported". I have a client that could use a high bandwidth link between two buildings that are 100' or so apart. The fiber link has already been busted twice. Heavy heavy trucks kill the ground concrete. I have configed a 54Mbps solution with two 1242G's and some cisco yagi's. But, if an N bridge is possible with two 1252AG's, and go faster than the 54Mbps..I'd go with that setup.
Cisco documentation says the bridge modes show up in the 1252 webgui and are selectable. They just end it with "not tested".
I've just bought an access point AP1141N for my small business but unfortunately there is only Radio 0- 2.4G available through web interface. It is working fine but I would like to have access to radio 1 (5Ghz) as well.
View 2 Replies View RelatedI have Eight AIR-AP1242AG-E-K9's accross our site that have 2 SSID's and 2 VLAN's that work well, I want to link one of the AIR-AP1242AG-E-K9 to another one using 5ghz patch antennas across a 50 metre gap, but I am puzzled on how to do this, as to create a root bridge and a non route bridge link I need to put the infrastucture SSID on and this must be on VLAN1 but I want the traffic from both VLANs to pass over this link. I just want to ensure the config will work as I need to go into a cherry picker to get to the non-root-bridge.
View 11 Replies View RelatedCurrently have access points located throughout our warehouse that use the AIR ANT5160V-R antenna's from Cisco. These AP's are 25' in the air. However we have a lot of voice quality issues off of the 5Ghz band, we do no other services on this band as we keep data on the 2.4Ghz.This was all installed by a vendor but from what I am seeing on the documentation [URL] the cover is extremely poor for these antennas despite AP's everywhere. They cover side to side but aren't a well rounded AP at all.it seems like the AIR-ANT5145V-R would be better suited even though this is a warehouse.
View 5 Replies View RelatedCan i run both 2.4 and 5ghz at the same time? so my N user's can connect at 300Mpbs on the 5ghz bonded, and my G users can connect to 54Mbps?Also i ask because of coverage, my 5ghz does not cover as far as the 2.4 so those at the extremity's could at least get G with a good signal?
View 4 Replies View Related1142N-E0K9 will support both 2.4 and 5 ghz or only 2.4 .
View 4 Replies View RelatedI'm currently moving to a 5ghz solution, due to my WGB's de authenticating due to possible interference. However, the area I have to cover is 350ft in length, with centralizing a 1242 with two Cisco Aironet 6-dBi Omnidirectional Antenna (AIR-ANT5160V-R), that leaves around 150 ft each way.
Do you think this is possible? I currently have a 12dbi high gain antenna on 2.4 right now, but I get the following:
Oct 3 18:05:26.359: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 68bc.0cb8.6a09
Oct 3 18:05:26.359: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0000.bcc7.ef05
Oct 3 18:05:26.359: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0000.bc58.c1ae
[code]...
I'm going to assume this is interference causing this, since we are in a factory with lots of noise. When the WGB is directly under the antenna/root bridge, there seems to be very little de authenticating.
trying to upgrade home network and found a dual-band 2.4Ghz and 5Ghz router. Appears that none of out newer Toshiba laptops and neither of our brand new Asus laptops recognize the 5Ghz network sitgnal. Only PC in entire house that sees the 5Ghz signal is the old PC in the house running Win XP.
View 7 Replies View RelatedI am looking into upgrading a customers wireless network and they are looking at using a few 1240 access points for both internal and external connections. Their question is can one access point support both channels simultaneously? They would like to connect an antenna on the inside of the building on the 5ghz channel and another externally on the 2.4ghz channel.
View 3 Replies View RelatedIn the old days I used two autonomous 1242AG access access points to create a 5GHz PtP link with 2 patch antennas (over small distance 50meters and on on private premises) to connect an small building or garage were there was no ethernet availible. and used the 2.4GHz radio to serve clients in the small building area, worked great.
Can I use the same setup with the 2602e access points? If so, would I be able to use them controller based? Can I connect a switch/or additional access point behind the 2602e (bridge) in the small building/garage? Would that addtitional access point be able to connect and register to the WLC.
We ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas instead of the 2.4GHz antennas.Would it be possible to use the 5GHz antennas as 2.4GHz antennas?If so, are there any down sides to it?
View 15 Replies View RelatedI have an AP541N-A-K9. For the past couple weeks it stops work at 5:00pm. The clients can see the SSID but when they connect it fails. The only way to get this to work again, is to set the radio to 5GHz 802.11N. Setting the radio to anything else does not allow the clients to connect.
I have some older clients so I need this broadcast G as well.
I have upgrade the software to AP541N-K9-2.0(1). Does not make a difference. Reset to Factory defaulst and reconfig does not make a difference. There are no Rouge AP's in the area.
Between the issues these have passing DHCP from a Windows server and now this, I'm thinking these devices are not fully baked.
I have e4200 router set up with different SSIDs for 2.4ghz and 5ghz. My laptop (Lenovo x220 with Intel 6205 wireless adapter) can't see the 5ghz network. I've tried changing the channel for the 5ghz network and it didn't fix the problem.
View 9 Replies View RelatedI am using the E2500 with the Wireless N-pci adapter with dual band, both with the latest drivers / firmware, and I am getting extremely low signal quality and connection speed when connecting to the 5 Ghz network.My computer is no more than 15 feet away from the router, and on the same level. I also verified the connection with the 2.4 Ghz band, and it reads as excellent, and with 54 mps. Using 5 Ghz I get one bar of signal quality (very poor) and no more than 13 mps connection speed.
View 9 Replies View RelatedMy dual-band 450Mbps TRENDnet TEW-684UB cannot find my Linksys E4200's 5Ghz SSID. I have changed the SSID of the 5Ghz band and it is broadcasting.
View 2 Replies View RelatedWednesday, November 23, 2011I have an Airport Extreme dual-band 2.4Ghz and 5Ghz. Each network is has a different name and different password so I know exactly which one I am connected to.On a MacBook Pro, it sees both networks. On a Dell E5520 it will see both networks. On an iPhone 4 it will see both networks. I can connect any of these devices to either network.Just got the Linksys E3000 dual-band 2.4Ghz and 5Ghz. Each network is has a different name and different password so I know exactly which one I am connected to.On a MacBook Pro, it sees both networks. On a Dell it will only see the 2.4Ghz network. On an iPhone 4 it will only see the 2.4Ghz network.The Airport Extreme is powered off when using the E3000 so I know there is no interference from this router.E3000 Firmware Version 1.0.04. It's the latest.5Ghz Wireless Settings Network Mode: Mixed Channel Width: Auto (20Mhz or 40Mhz) Channel: Auto (DFS) 2.4Ghz Wireless Settings Network Mode: Mixed Channel Width: Auto (20Mhz or 40Mhz) Channel: Auto (DFS)Did not mess with any other settings. I have rebooted the computer, cycled the router and modem 3-4 times.Nothing works.My question is since both laptops and phone can see the 5Ghz network when running the Airport Extreme, why doesn't the 5Ghz network show up on the Dell and iPhone when running the E3000.
View 5 Replies View RelatedMy channel width is Channel Width is 40 mhz only, and my channel is Auto DFS?These seem like good settings?My macbook air sometimes see's my 5ghz wireless SID, and sometimes it connects to it, but i still have no internet access for some reason
View 3 Replies View RelatedI've found a few people with this problem on the internet. I'm using my phat 360 with the black N adapter. e2500 is updated to the latest firmware. But my 360 cannot connect to the 5ghz N, only 2.4ghz g. The wierd thing is that the 5ghz signal gives a better signal than the 2.4ghz.
I just found a thread on google talking about the e4200 and someone mentioned counterfit adapters and problems with them. I did buy this on ebay for a cheap price, so it looks like it was too good to be true. this is a counterfit? It does have a real hologram on it.
[URL]
If this is real, what else could be the problem. Has the firmware not been updated to support the 360?
EA2700v1 WPS-PIN using 5GHz does not work. This router includes WPS header in its 5GHz beacon and probe response but the router removes the WPS header from them once WPS-PIN starts. There is no problem with WPS-PIN using 2.4GHz.
View 1 Replies View RelatedDo the Dell Wireless 1506 or 1703 cards support 802.11n over 5GHz?
The documentation I found indicate support for 802.11n over 2.4GHz but I have not found definitive confirmation that 5GHz is supported.
By default, 802/11a/n is set for backhaul communication.Does that mean that if most of my clients are on 5ghz, Mesh network is not a preferred design to go? Reason being:- client communication on a/n radio might disturb the traffic of the whole cell and of all the MAPs that connect to the network through that MAP.
View 6 Replies View RelatedIs it possible to connect directional antenna on slot 1 5Ghz radio on the 1522SB and use it for client access ? As per the deployment guide there is a note that Omni antenna is required on slot1. If i connect directional antenna on slot 1(how will the AP know if its omni or dierctional antenna which is connected anyway) , will it work ?
View 3 Replies View RelatedIn my class room, a lot of new Dell notebook (university purchased) all of those are the same model. Those came with 2.4&5Ghz WLAN NIC.
So, my WLC-based AP in that room which is Cisco 1x1042 & 1x1252 running in light-weight.This make huge congest on 5 Ghz. All of my 41 NB go for 5Hgz. And Zero client on 2.4Ghz radio, 2.4Ghz is not utilized at all.
I have read a lot of those related discussion. But I even can not find one that need to utilized BOTH of band. Most of those discussion talking to band-select which is "this feature only goes in one direction from the 2.4 GHz range to the 5 GHz not visa-versa."
My constrint is We can not touch the NB. Because this is university, much many diverse user loging in.
I'd like to set up a 2.4Ghz and a 5Ghz SSID at the same time, using one Cisco AP541N-E-K9. But I can't figure out any way to do so.
View 1 Replies View RelatedWRT610v2 running latest firmware.
xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.
Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars. Connects to 2.4 network just fine, Won't pull an ip address and reports "Not connected" when I select the 5.0 network.
I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network. So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not. If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
just got my AE3000 today. It's working fine. The box says "2 GHz or 5 GHz" but there are no instructions on how to select one or the other. I don't even know which it is using. How do I set this? I'd like to make sure it's on the 5 GHz band.
View 1 Replies View Related