Cisco Wireless :: Setup 2.4Ghz / 5Ghz SSID At Same Time Using One AP541N-E-K9?
May 6, 2013I'd like to set up a 2.4Ghz and a 5Ghz SSID at the same time, using one Cisco AP541N-E-K9. But I can't figure out any way to do so.
View 1 Replies
ADVERTISEMENT
Cisco Wireless :: AIR-CAP3502I Run Both 2.4Ghz And 5Ghz Simultaneously?
Jan 28, 2013Can i run both 2.4 and 5ghz at the same time? so my N user's can connect at 300Mpbs on the 5ghz bonded, and my G users can connect to 54Mbps?Also i ask because of coverage, my 5ghz does not cover as far as the 2.4 so those at the extremity's could at least get G with a good signal?
View 4 Replies View RelatedCisco Wireless :: AIR-LAP1142N-E-K9 Will Support 2.4GHz And 5GHz Or Not?
Jun 4, 20121142N-E0K9 will support both 2.4 and 5 ghz or only 2.4 .
View 4 Replies View RelatedCisco Wireless :: AIR-LAP1242AG-E-K9 / 5GHz Antennas On 2.4GHz Radio?
Jul 16, 2012We ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas instead of the 2.4GHz antennas.Would it be possible to use the 5GHz antennas as 2.4GHz antennas?If so, are there any down sides to it?
View 15 Replies View RelatedLinksys Wireless Router :: E2500 2.4Ghz Won't Connecting At 5GHZ Frequency
Feb 23, 2013On my dual band E2500, I have both the 2.4 and 5 GHZ enabled. I have a fairly new HP with an N wireless card but I cannot get it to connect at the 5GHZ frequency. The only computer that will connect at the speed is my wife's with an external Cisco wireless card. What the settings should be on the PC in order to get it to connect at the higher frequency?
View 4 Replies View RelatedLinksys Wireless Router :: E3000 - How To Get Info About Usage 2.4ghz Or 5ghz
Mar 19, 2011How do I know if I'm using 2.4 or 5ghz? I would like the laptop and ps3/net flix to use the 5ghz and everything else to use 2.4ghz. I used the e3000 CD fro the setup. When I was at the last part of the setup, when it gives you a ssid name and password. I deleted it and typed in a name that I could remember. I clicked the button for the next step and everything was complete. I also received another name for guest to use the computer. The e3000 setup just game me some wild name like running water.
I would like to know since I have two different names, which on e is using 5ghz and which one is using 2.4thz? Can you tell me if the e3000 automatically have the first name use 5ghz and the guest just 2.4ghz on the second name?
Cisco Wireless :: AP541 / Establish WDS-connection On 5GHz And Connect Clients On 2.4GHz?
Sep 27, 2011Is it possible to establish the WDS-connection on 5GHz and connect Wireless-Clients on 2,4GHz with these Acces-Points?There are some threads concerning performance-issues in combination with WDS on 541 - any news on this with the actual software-release?
View 1 Replies View RelatedCisco Wireless :: 1142 / 5508 - User Switching Every Few Minutes Between 2.4ghz And 5ghz?
Aug 20, 2012This first started when a user said they were getting disconnected and reconnected a few times a day to our wireless network. He is in a remote office with a 1142 which is set to H-Reap talking back to our 5508. Our WLC is running 7.0.166 The laptop has an intel ulitmate 6300agn wireless card with the latest 15.x drivers.
We are using an SSID with wpa2 and 802.1x auth back to our ACS server using PEAP with our windows credentials.attached is what i am seeing on the wcs troubleshooting page.When i do a debug client on the WLC i see many reauthentications coming from the client on the different radio.
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Reassociation received from mobile on AP 0c:85:25:f3:7d:40
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c 10.24.8.108 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying site-specific IPv6 override for station 00:24:d7:d1:16:6c - vapId 512, site 'VH-GasWorks', interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying IPv6 Interface Policy for station 00:24:d7:d1:16:6c - vlan 2, interface id 0, interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying site-specific override for station 00:24:d7:d1:16:6c - vapId 512, site 'VH-GasWorks', interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c 10.24.8.108 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c STA - rates (8): 140 18 24 36 48 72 96 108 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Processing RSN IE type 48, length 38 for mobile 00:24:d7:d1:16:6c
[code]....
Now this may be not be the issue thats causing our dropouts a couple times a day as this is happening every 5 mins.
Linksys Wireless Router :: E4200 2.4Ghz Network Drops Connection 5Ghz
Oct 15, 20112 days ago my e1000 died, so I went big and bought the e4200 (due to newness, its already loaded with Firmware 1.0.03 build 14) to aleviate my networking woes. I'm running into an issue where I'm utilizing both the 2.4Ghz bands and the 5Ghz band. My desktop as an AE1000, and I'm utilizing that on the 5Ghz band. Everything else in the house (Dell laptop, 2x iPhone 4 and an HP printer) are all connecting to the network wirelessly.
I have had 0 network issues with regards to my wired connections, or my 5Ghz connection. But my 2.4Ghz connection will continuously be unavailable. I have both bands set to brodcast, they have different names so my AE1000 can connect via 5Ghz band. Both yesterday evening, and this morning, my phones, laptop and printer cannot connect, and for the most part, the network doesn't show up on available networks. When it does show up, the devices can't connect.I'm proficient enough to do the general home networking, but I'm at a loss as to how to fix this, without a daily reboot of the router (which seems excessive and unwarranted for a 2 day old e4200 [or any router to be honest]).
Cisco Wireless :: AP541N Drops All Clients Unless Radio Set To 5GHz 802.11N
Apr 2, 2012I have an AP541N-A-K9. For the past couple weeks it stops work at 5:00pm. The clients can see the SSID but when they connect it fails. The only way to get this to work again, is to set the radio to 5GHz 802.11N. Setting the radio to anything else does not allow the clients to connect.
I have some older clients so I need this broadcast G as well.
I have upgrade the software to AP541N-K9-2.0(1). Does not make a difference. Reset to Factory defaulst and reconfig does not make a difference. There are no Rouge AP's in the area.
Between the issues these have passing DHCP from a Windows server and now this, I'm thinking these devices are not fully baked.
Cisco Wireless :: Connect AP541N To RV220W To Use Same SSID
May 21, 2012I would like to connect the AP541N to the RV220W and use the same SSID assigned to both throughout the office, for seemless client movement. I would like to keep the AP541N connected via the internet cable, as it will be on a switch which is on the same segment. The access point has many different configuration methods available, but the router appears to only have WDS as an option to connect the two devices. I would rather not use the WDS feature on the AP, as I want to utilize as much bandwidth available as possible, and I assume using that method I would need to remove the ethernet cable from the switch.
Is it as simple as configuring both devices with identical VLAN settings? I am preconfiguring the devices before installing them, as to minimize downtime, so would like to make sure the configuration is correct.
Cisco Wireless :: AP541N Specification For Ack Time Adjusting And Survey
Nov 8, 2010Some deep technical questions regarding the AP541N access point? What I want to know is, if the AP has: - Watchdog per IP - ACK time adjusting - Site Survey.
View 1 Replies View RelatedLinksys Wireless Router :: EA4500 5GHz SSID Cannot Be Hidden?
Sep 10, 2012I have found that if I do not enable the broadcast SSID option on my 5GHz N network that my devices will forget the network and not reconnect on their own. Yet, I have the 2.4GHz G/N network set up to not broadcast my SSID and I have no problems. Why can't I disable my SSID broadcast on the 5GHz N network without these problems?
View 9 Replies View RelatedLinksys Wireless Router :: E2500 5ghz Ssid Not Visible?
Dec 25, 2012None of my wireless devices (Windows, iphones) can see the SSID from the 5ghz channel on my E2500. I have updated the firmware and reset the router to factory defaults. Still not visible. The router is set up to broadcast the SSID under wireless settings. Also, selecting "other" under iphone>settings>wifi and entering the SSID name and password gets "could not find the network (ssid)". This was working until a couple of days ago Comcast power cycled the router to make sure my cable modem was working. Now nothing.
View 2 Replies View RelatedLinksys Wireless Router :: E2500 Unable To See 5GHz Channel SSID
Jul 1, 2012I've recently purchased the E2500, done the setup but am facing some issues.I'm unable to see the 5GHz channel SSID, I can only see the 2.4GHz channel SSID.Have tested all the laptops and devices at home and all can't see the 5GHz channel.The list of devices are:
a) iPhone 3GS
b) iPhone 4G
c) iPhone 4GS (some sites says it doesn't support, some says it does, I'm confused as a result)
d) Samsung laptop
e) Dell laptop
f) Momo11 Little Bird Edition tablet (Made in China [MIC])
g) No name MIC tablet
Secondly, is there any tips / tricks to tweak the modem to increase the internet speed?
Linksys Wireless Router :: E4200 Disabling SSID Broadcast For Both 2.4 And 5GHz Stops Blinking
Jul 1, 2011I was quite excited about E4200 I got yesterday. Everything works perfect except front LED light start blinking a few hours later. Don't know why it happens in a sudden and non-stop. After several tries, I found that disabling SSID broadcast for both 2.4 and 5GHz stops the blinking.Of course, before doing that, I upgraded firmware to 1.0.02, reset to factory defaults and finally set up E4200 manually rather than using Cisco Connect. Now the LED light is continuously lit.
View 4 Replies View RelatedD-Link DIR-825 :: No Link Between 2.4GHz And 5GHz Clients?
Dec 15, 2011How come my 2.4GHz client can't see my 5GHz client? Shouldn't they be visible through the DIR-825 router?
View 1 Replies View RelatedCisco :: Wireless Access Point AP541N-E-K9 Setup
Oct 2, 2012I have installed the following wireless access point on our network:
-Product Identifier: AP541N-E-K9
-Hardware Version: V01
-Software Version: AP541N-K9-2.0(0)
I have created 2 VAP's and give each one an SSID. They both have the same VLAN ID. I have setup as follows:
1) The first VAP I would like to give internet access and access to our internal network shares.
2) The second VAP I only wish to give internet access and no access at all to our internal network (for guest access). I am also using HTTP redirect with this.
how can I achieve the setup in number (2)? This is to give internet access, but not share the internal network.
Belkin Routers :: AC900 - Can't See Broadcast Ssid For 5ghz Band
Dec 29, 2012F9K117 - I can't see my broadcast ssid for the 5ghz band. Is there anything I can do?
View 3 Replies View RelatedWireless Netgear SSID Disappears Daily At Same Time?
Dec 18, 2012Every day around the same time the SSID for my wireless network disappears. I'm using a Netgear wnr2000v3. Prior to this I was using a Linksys router, which did the same thing... only more frequently (2-3 times a day).Between smartphones and laptops, there are about 6 devices connected to the network. They all lose their connection and cannot find the broadcasted SSID when this happens.Because it happens around the same time each day, it makes me think that it has something to do with the DHCP lease, which is 24 hours. Just a thought, as I don't really know how that works.
View 4 Replies View RelatedD-Link DIR-825 :: 2.5ghz Not Working / Why Time And Date Keeps Changing
Jul 17, 2011I have a DIR-825 router connected to my cable modem. The 2.4ghz constantly goes down but not the 5.0ghz. Our wireless devices will see the connection but we are unable to connect.We only have one device that uses the 5.0 and multiple devices that use the 2.4 and none of them can connect.I am currently running firmware 2.02. I also notice that the time changes and I have to reset the time/date.I have tried rebooting the device, resetting the router, changing the network key, updated the time/date, renewed the DHCP...I don't know why it keeps going down, why the time/date keeps changing, and why I cannot get the 2.4 working.
View 13 Replies View RelatedCisco Wireless :: How To Setup 4 WAP321 With 1 SSID
Oct 10, 2012I just bought 6 Cisco WAP321.
What I want is to have 1 SSID for all 6 WAP so all employee from 2 floor building can access.
WAP # 1 connect to LAN with cabe and setup as Master with WDS Bridge enabled. WDS interface is also enable with MAC address input from WAP #2; WAP #3 & WAP#4.WAP #2 connect to WAP #1 via wireless with WDS Bridge enabled. WDS
[Code].....
Cisco Wireless :: WAP321 How To Setup Separate Guest SSID
Dec 11, 2012how to setup a separate SSID for guests (without a password).
Basically, we have one SSID now called Mnet which has a WPA2 password. For guests coming in i want Mnet Guests where people can connect without needing a password. They should be able to use internet but not connect to LAN devices, how to accomplish this with this WAP321?
Cisco Wireless :: Setup WRVS4400N To Isolate Guest Totally From Internal SSID
Jan 25, 2011A query here with regards to Wireless isolation between SSID and wireless isolation within SSID.If we have 2 SSID, eg. InternalSSID, GuestSSID on AP1.Both SSID are set to Enabled for isolation between SSID, and within SSID, that would mean all machines connected thro' this AP1, would be isolated from one another.
1) If there's 1 laptop that connects to another AP, lets call it AP2, (doesn't have isolation function) on ssid01. Would this laptop still be isolated from those that connects to the first AP?
2) If there are wired PCs connected to the router. And the 2 APs are connected to the same router. Would the machines connected thro' the AP1 on either InternalSSID, GuestSSID be able to access those wired PCs? (My assumption is yes.)
3) Is there a quick and efficient way to setup on WRVS4400N to isolate GuestSSID totally from InternalSSID, and wired PCs. InternalSSID and wired PCs should be allowed to 'see' one another.
The challenge here is that, the network points are all installed already. Both AP are connecting thro' 2 separate unmanaged switch together with a couple of other PCs. 1 Port on the unmanaged switch, each,connects to the router.
Cisco Wireless :: Setup First Time Rv110w Vpn?
Jan 29, 2012i have a cisco rv110w vpn/firewall/wifi and am trying to get vpn up and runing so vp can login from home and do his work.
View 1 Replies View RelatedLinksys Wireless Adapters :: AE2500 - Have To Put Cd In And Run Setup Every Time Want To Get Online
Apr 10, 2012I have to put cd in and run setup every time I want to get online. WHY
View 2 Replies View RelatedHome Network :: How To Setup Same Wifi Ssid Over Large Area
Jul 2, 2011I'm trying to setup my wifi at home and want to cover all the areas under same SSID and allow roaming cross since one router can not cover 20000 sq ft over 3-4 levels.I anticipate at least 8 if not more to cover everywhere.How do I setup a WLAN network for myself. I have a cat6 cable running in quite a few rooms.Basically my end game is have uninterrupted wifi access everywhere in the house Possibly run a SIP based PBX over wifi wherever possible, close to 24 extensions.I also laid down cat6 in most rooms to allow to setup my own central media server with that as well but that's a different topic and forum I guess.Can I use the cat6 coming into the rooms, connect it to the wifi router and provide Internet access over wifi and use the router as a hub to connect a cat6 from the router for the media player and another one to a sip based Pbx extension or have the Pbx extension be on wifi?Damn sorry for such a confusing and loaded sentence.
View 18 Replies View RelatedCisco Wireless :: Aironet 1250 With 2x 2.4Ghz Antenna?
May 7, 2012I need to upgrade a 1230 to the new Aironet 1250 at a location. I have only 2 external antennas at that location.
I understand that you still can run 802.11n with 2 antennas. But I can not find anywhere in WLC 5508 v7.2 that I can disable the middle nut (C)
Cisco Wireless :: Configure 802.11n On WLC4404 Or WLC5508 In 2.4Ghz?
Aug 15, 2012how to set up support 802.11n on WLC4404 or WLC5508 in the 2.4Ghz? WLC4404 supports 802.11n? or support this protocol only in the brochures? I spent a few days, but did not get the result. I'm connected at speeds 65/130Mbit, but the real speed tests never exceeded 45Mbit. The AP from the test laptop is 7-10 meters.I tested the laptops with a Linksys AP E1200-EE ( 40Mhz, FastEthernet uplink port...)and received nearly 100Mbit!
At WLC5508 able to connect at speeds 150/300Mbit/c but only in the 5GHz band, but real speed tests never exceeded 70Mbit.In 2.4Ghz range I connected at speeds of 130/144Mbit/c, but actual measurements showed no more than the 45Mbit.
All tested with iperf and with site speedtest.net.
iperf -w64K -s
iperf -w64K -i 2 -t 300 -c x.x.x.x
Laptops: Asus (Atheros AR9002WB-1NG) and Sony (Advanced-N 6230).
My tests AP: 3501I-E and 1252AG-A
SW on WLC5508 7.2.110.0
AP tested in different variants - open system and WPA2+AES.
[code]....
Cisco Wireless :: Possible To Use 2.4ghz Air-ant1728 Antenna On New 802.11a Cardbus
Oct 13, 2002Can I use the 2.4ghz (product #)air-ant1728 antenna on the new 802.11a cardbus?
View 3 Replies View RelatedTime Warner Internet / D-link Router Setup?
Jan 27, 2011I am trying to set up a d-link router with a modem provided by time warner cable. I've powered down, reset the router, and I've put it on dynamic settings (sorry if that's incorrect terminology... not a comp. buff). I can't get my wireless to connect to internet.
View 1 Replies View RelatedCisco Wireless :: 1130 - 2.4Ghz Interference In Crowded Space
Sep 11, 2012We have a small ofice in the 3rd floor of a building and we are using 2 access points Aironet 1130 URL
Since some time now the space has become really crowded with access points. 1 AP is on channel 5 and is almost unusable. The 2nd one on channel 11 has some APs to fight with and with smaller signall strenght.
I have been researching and read a bit about changing some access point parameters (RTS/CTS/timers) on a multi access point environment. I want to do that while waiting for 5GHz AP's (and because not all clients support 5GHz).
Linksys Wireless Router :: EA4500 2.4GHz Not Transmitting
Apr 3, 2013I purchased a EA4500 and at first I could connect to it through its default ciscoxxxxx ssid on my laptop which is 2.4GHz only. I upgraded the firmware using the PC utility and now I can't find the 2.4GHz SSID no matter what settings I do. I've disabled and enabled it multiple times, changed it to have no security or with security and enabled and disabled it and renabled it. Nothing seems to work, but for some reason the 5GHz side I can connect to using a 5GHz device. I've also tried disabling the 5GHz side, but still no 2.4GHz.
View 4 Replies View Related