Cisco Wireless :: Connect AP541N To RV220W To Use Same SSID
May 21, 2012
I would like to connect the AP541N to the RV220W and use the same SSID assigned to both throughout the office, for seemless client movement. I would like to keep the AP541N connected via the internet cable, as it will be on a switch which is on the same segment. The access point has many different configuration methods available, but the router appears to only have WDS as an option to connect the two devices. I would rather not use the WDS feature on the AP, as I want to utilize as much bandwidth available as possible, and I assume using that method I would need to remove the ethernet cable from the switch.
Is it as simple as configuring both devices with identical VLAN settings? I am preconfiguring the devices before installing them, as to minimize downtime, so would like to make sure the configuration is correct.
View 1 Replies
ADVERTISEMENT
Sep 25, 2011
trying to get my new router and bridge to work I am close to give up.
1. I have bought a RV220W router this will be connected to Internett and all wireless devices will connect to it. It seems to work fine. I have enabled on AP profile where others easyli can access internett through router WAN port
2. I have bought a AP541 Access point that i want to have as a bridge (We earlier used 3COM without problems) Some Computers and other stuff like printers will be connected to this through a switch for the Ethernet port on AP541. (I dont want any clients to connect wireless to AP541N)
Before I start asking detailed questions, i want to verify that my setup is possible. Reading the Information on the shops webpage clearly states that AP541N can work in bridge mode, but struggling to find any good explenation makes me wonder if this really is true.
Can Cisco AP541N works as a bridge together with RV220W.
View 1 Replies
View Related
May 6, 2013
I'd like to set up a 2.4Ghz and a 5Ghz SSID at the same time, using one Cisco AP541N-E-K9. But I can't figure out any way to do so.
View 1 Replies
View Related
Nov 3, 2011
I have an rv220w router with one SSID and the product says I can add up to 4 additional wireless ssid ie the router is protected with wpa but we have guests that would like to connect to the internet while working in our building . I would like to add a guest SSID with wep security that I could give Clients. The problem I run into is every time I add the Guest ssid the wireless printers that are attached to the routers' main ssid quit working. I noticed that when the rounter was orginally set up the main SSID has IP addresses from 100 to 255 allocated. Do I need to limit the IP addresses in the Main SSID to a smaller number so that the Guest SSID can use the remaining addresses.
View 2 Replies
View Related
Aug 20, 2012
AP has static IP with 2 SSIDs setup, one for guest one for domain access(both have the same issue), tried with multiple devices, both win and MAC, all show "connected but with limited access", ipconfig on those devices, all show ip "169.254.X.X", but event log on AP indicates that "authentication has been completed sucessfully".
using RADIUS server for authentication. management VLAN ID "1", SSID VLAN ID "11"
View 5 Replies
View Related
Aug 10, 2010
Can the access point AP541N connect to wireless clients with 802.11g/a simultaneously?
View 1 Replies
View Related
Dec 24, 2012
I just got a cisco RV220W and I try to connect it on my wireless network as client, but it doesn't work.
View 1 Replies
View Related
Jun 28, 2012
I'm trying to setup 2 VLAN's 1 for Native Traffic on my Corp network and another VLAN for Guest Wireless traffic. I have attached the Config from my Cisco AP1231 and my Cisco 3750. I have the AP plugged into port 24 on my switch. I seem to have the VLAN's working fine. I can get the AP1231 to broadcast both SSID's and the very first time i can connect everything seems to work fine. after i power down my switch and AP i cannot connect to either SSID. I get the message Not Connected.
View 2 Replies
View Related
Apr 22, 2012
I have my all my computers, printers setup with a wireless network with dsl modem connected to linksys wireless router. I just signed up with comcast with another wireless router. I do not want to reconfigure all the laptops and printers with the new comcast wireless SSID. Is there a way I can connect the linksys router with existing SSID with the comcast router and using the internet speed of comcast. (note. will disconnect service with dsl)
View 3 Replies
View Related
Aug 21, 2011
I just recently installed a RV220W at my office and (almost) everything works fine. I have noticed that when my iPhone is connected to the RV220 wi-fi network, I get the message "The connection to the server failed" when checking my email. If I disable the wireless on my iPhone, it connects up to the exchange server perfectly fine so it must be a setting with the wireless somewhere but I cannot find it anywhere.....
View 1 Replies
View Related
Dec 19, 2011
I provide support for a small business network. ISP: Silo Wireless (wireless point to point with ISP) Router: Cisco RV220W Wireless-N Network Security Firewall
The router is configured with two wireless access points with SSIDs: "abracadabra" and "abracadabra-guest". The only difference between these two wireless networks is their passcode. Up until now I have had no problem connecting devices to either wireless network.
My problem lies with an HP Pavilion laptop running Windows Vista Home Premium 32-bit that I'm trying to connect to the "abracadabra" wireless network.
Network and Sharing Center shows "Identifying" for a while and then shows "Unidentified network" with no local or internet access. Wireless network connection status says that Media State is Enabled, Speed is 54Mbps and Signal Quality is Excellent. Network Connection Details shows that DHCP is Enabled but it's getting an Autoconfiguration IPv4 address of 169.254.107.138...
The laptop is running ESET Nod 32 Antivirus 5 and Windows Firewall and I've disabled Windows Firewall on the Wireless Network Connection. I've also tried re-installing the wireless nic driver, it's running the latest from Windows Updates.
what really gets me is that the laptop can connect to "abracadabra-guest" fine and access the internet
View 3 Replies
View Related
Nov 15, 2011
I have a WAP4410n which has been configured with a single SSID since implementation several weeks ago with no issues. I am now trying to add a second SSID and not having any success. Originally the second SSID was not being assigned a MAC address and thus not being broadcasted. After upgrading firmware to 2.0.4.2 I now see a MAC address associated with second SSID and it is being seen by clients, but they still cannot connect. I reset the AP to default settings and reconfigured from scratch but still no luck. I have two of these APs, the other one is still at FW rev 2.0.1.0 and has same issue (it does have MAC address associated with second SSID so I didn't bother upgrading firmware yet).
I have tried a few different authetication options, including disabling authentication, to no avail. Question - I do not see an IP address associated with the second SSID - is that the problem and if so, how do I fix that?
View 1 Replies
View Related
Apr 22, 2013
I have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
View 3 Replies
View Related
May 6, 2011
actually, i have 2wire DSL Router and i am using SSID Broadcast Disable after disable i can't connect wireless to my extra device too for example my Blackberry. but i am using another computer with wireless but i can't connect blackberry and iphone i don't have more idea in wireless stetting what can i do?
View 2 Replies
View Related
Jun 11, 2012
In the company we have two SSIDs for corporate and guest networks respectively when I try to connect to any of the SSIDs it doesn't happen until 5 retries. The only log I get that seems to be related to it is the following:
*Jun 11 11:48:09.062: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:23:32:73:d7:15 due to switch of WLANs from 1(femsawl) to 2(visitas)
Here it shows a switch between SSIDs but if you just turned on an apple device and try to associate for the first time to any of the SSIDs the scenario is the same, several tries to connect.I am running a 4402 wlc with 6.0.202.0 software version.
View 4 Replies
View Related
Sep 15, 2011
Has anyone come accross a problem whereby an SSID becomes unavailable when selecting a Radio Policy of '802.11g Only'? The SSID is configured identically accross multiple controllers, but only works on the WISM's. The same WLAN profile on a 5508 is unavailable unless I select a Radio Policy of 'All'.
All controllers (WISM's and 5508's are running 6.0.188.0)The WLAN profile is using MAC Filtering[WPA2][Auth(802.1X)] as the security policy.
View 3 Replies
View Related
Oct 9, 2011
I've had my E3000 for almost a year now and it's been great - until recently. Latencies have become patchy for some users and most surprisingly, the 5GHz network has stopped using two channels. I did a 30/30/30 reset on it a few minutes ago and re-configured the whole thing. It's set to use 40MHz Only and WPA2 Personal, but speeds at the physical layer are still just 144 Mbps and in the web interface's Status page it clearly says "20 MHz".
Why might this be? It was fine for so long, only to refuse to use two channels now. I've checked what the other wireless networks in my area are like, and none of them are even 5GHz-capable as far as I can tell, so the relevant spectrum shouldn't be overcrowded. It's rather nice to have the two channels for NAS transfers and streaming and such.
After manually specifying a base channel (48 at the moment), it actually kicks into 40MHz. The problem is now that my clients, both using a WUSB600N, are getting "Unable to connect to (SSID)" pretty much instantly after clicking the network in Windows.
View 1 Replies
View Related
May 22, 2013
I have one cisco wlc 2112 with ios 7.0.230.0 with license to support 12 access points. My access points are nine (9) lap1231ag and one (1) lap1310.I just have one wlan (ssid). My scenario of deployment is in layer 3. I have one interface management and ap manager in the WLC. All my Access Points have differents ip address that WLC. I need to configure a unique ssid to associate my six (6) dynamics interfaces (each dymanic interface with different vlan subnet).Each wlan profile (ssid) should have the same security in phase 2 (wpa2/psk). My cisco access points don't support hreap. My wlc support only (4) interface into an interface group, and i need six (6) dynamics interfaces.
View 6 Replies
View Related
Jan 1, 2013
My 'main' Wifi SSID will just disappear and you can't connect to it. the guest account will still show up. computers/devices that are already connected will stay connected and will work fine, but anybody reconnecting will not be able to. Only solution I've found so far is to unplug and replug in my router
View 1 Replies
View Related
Feb 11, 2012
I am having trouble connecting my wireless devices to the e4200v2. My e4200v2 is connected to my action tec ver.F for fios. It's a LAN to LAN connection where the action tec is primary. I followed the directions changing the Secondary router address to 192.168.1.2 and the action tec stayed at 192.168.1.1. I also reset the action tec prior to any attachments (because I had an old belkin n+ connected). i also disabled DHCP in the secondary router. Both 5 & 2.4 Ghz have different passwords although I did try having them have the same password- no luck. I can't connect for whatever reason. Both network modes are mixed. On the action tec- the wireless is disabled. SSID are different. Can't connect for whatever reason. I am at a loss. I don't know if this is relevant- I use windows vista.
View 9 Replies
View Related
Nov 10, 2011
So I have this E1500 Router that worked fine for the past 5 months, then out of the blue, the wireless feature ceased to function... laptops were not being able to connect to the wireless, the router was also not broadcasting the SSID.So, here's what I have done so far:
1. Check the router software settings, all was good there.
2. Did a "hardware reset" pushing the red button. (now this solved the problem, BUT only for a day, when power is turned off for the night, the next day it's non-functional again. The cycle can be repeated daily, but its a pain to reset and set it up everyday)
3. Updated the Firmware, and this somehow solved the problem for 3 Days... and now it's back to non-functional, again out of the Blue.
Is the Router just busted and it's not remembering the settings?
View 2 Replies
View Related
Sep 17, 2012
Using CCC with EA4500, where do I find the control for enable/disable broadcast of the SSID?
View 5 Replies
View Related
Nov 14, 2012
I just installed this WAP, updated the firmware. Windows computers can connect. iPads and iPhones can't connect. All iOS devices are runnign 6.01. The iPad can see the nework and it says it joins, but it can't browse the Internet. The iPhone does not even see the SSID. The WAP is pretty much at the defaults. I am using WPA personal, 5GHz. The iOS devices were working fine with the Netgear that was installed previousley. I checked this article and the WAP seems to be configured right:
View 1 Replies
View Related
May 24, 2011
I am using RV220w router firmware 1.0.1.0
I can connect to the SSL VPN server using XP,windows 7 and window 2003 all 32bit stack 1. When I go to use windows 7 Prof. 64 bit IE v8 it will not connect. I dont even get where the laucher install. I get the error Please enable active X or make sure your site is trusted. All of this has been set yet it will not work. I also get the following error
Webpage error details
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; Win64; x64; Trident/4.0; .NET CLR 2.0.50727; SLCC2; .NET CLR 3.5.30729; .NET CLR 3.0.30729)Timestamp: Wed, 25 May 2011 18:00:28 UTC
Message: Object required: 'VPLaunch1'Line: 212Char: 1Code: 0URI: [URL]
the source code is ref. line 212
}
View 1 Replies
View Related
Jul 18, 2011
I have an Cisco RV220W and I can’t connect to web interface. The router is new, I receive the error in Mozilla: Cannot communicate securely with peer: no common encryption algorithm(s). I used also Internet Explorer, Chrome , I tried to disable SSL 3.0, TLS 1.0 but the problem persist. The PC obtained IP address from the router, I have ping on it ,also the SSID is up with open network I reset to factory default but the problem persist.
View 2 Replies
View Related
May 15, 2011
I'm relatively new to establishing VPN connections and I'm having one heck of a time getting everything configured.I'm setting up a RV220W at the office and trying to get VPN steup. I've have gotten Quick VPN connections working using the QuickVPN software. I've given up for now on IPsec VPN connactions and will come back to these later.What I'd like to get setup is the SSL VPN connections using the Win7 built in VPN client. Is this even possible? I initially tried to connect to the VPN via the SSL Web access but I cannot get the software/divers to install on any of the 3+ Win7 64 bit machines I tried.So can the SSL VPN on the RV220W be setup to connect to with the Win7 VPN Client using SSTP?
View 6 Replies
View Related
Feb 28, 2012
I just installed a brand new AP541N-A-K9 (running AP541N-K9-2.0(1) software) and cannot seem to add a SSID. I've tried both from CCA and directly from the Web interface (Wireless:Wireless Network Setup menu). The Add Another button doesn't seem to do anything. I've even tried multiple browser versions.
View 1 Replies
View Related
Jun 19, 2011
I have 3 AP541N. I become this not in a cluster. The APs standalone in the room. The first AP connect with cable to a DHCP Router from a other manufacturer. The other both APs should be connect over WLAN.How I must configure the APs? Which parameters must install?
View 1 Replies
View Related
Mar 9, 2012
I'm having problems connecting to the VPN. I can access the web portal, but cannot connect SSL VPN on my Mac 10.7, or a virtual windows 7 machines. I've read a lot of forum posts about the mac problem, but for some reason the Windows 7 machine won't connect SSL VPN on windows 7 x64, Chrome, FIreFox.
I tried downloading QuickVPN and set up a user account, but it just sits on the machine at the "Connecting" screen. My primary users will be running Windows 7 Professional x64.
View 1 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
Feb 12, 2013
I have 2 AP541N access points. Have been working well for a couple of years. Later last year they just dissapeard from CCA one day. COundt access them but they were still delivering 'wireless' so to speak I have recently put them back to defaults to try and get them back in to CCA. i had one, but not the other. They would work fine via GUI/web access.Then i updated them to 2.0.4 (both images) and since doing that i have no access to either of them via any form.
View 2 Replies
View Related
Nov 20, 2012
I mistakenly mis-configured "Management ACL mode" on my AP541N.
Administration>Administration Access Control>Managment ACL Mode
I set this to "Enabled", the problem is I only entered 1 IP address, and that IP address is the SAME IP as the AP's own internal interface. I was not thinking and entered that IP out of habit when I meant to enter my workstation's IP. The FW does not have a safeguard against this.
So, as you can see, this is a big problem, because now I have completely cut off all access (That I can think of) to the router. I can never access the AP as that IP because if I set my workstation to that IP, 1) There will be an address conflict, 2) My computer won't route traffic to the AP out its NIC because it recognizes that IP as itself.
View 2 Replies
View Related
Jun 20, 2010
As I posted about in the other AP541N thread about degraded performance, mine did a strange client disconnect last week. It dropped all authenticated clients, but they all thought they were still connected. A quick disable/enable of the wireless card on the laptop would get the computer back on the AP.
This same thing happened again today.
Device information and configuration:
Device: AP541N
H/W: V01
[Code]......
View 20 Replies
View Related
