Linksys Wireless Router :: E3000 - Unable To Connect To SSID

Oct 9, 2011

I've had my E3000 for almost a year now and it's been great - until recently. Latencies have become patchy for some users and most surprisingly, the 5GHz network has stopped using two channels. I did a 30/30/30 reset on it a few minutes ago and re-configured the whole thing. It's set to use 40MHz Only and WPA2 Personal, but speeds at the physical layer are still just 144 Mbps and in the web interface's Status page it clearly says "20 MHz". 
 
Why might this be? It was fine for so long, only to refuse to use two channels now. I've checked what the other wireless networks in my area are like, and none of them are even 5GHz-capable as far as I can tell, so the relevant spectrum shouldn't be overcrowded.  It's rather nice to have the two channels for NAS transfers and streaming and such.
 
After manually specifying a base channel (48 at the moment), it actually kicks into 40MHz. The problem is now that my clients, both using a WUSB600N, are getting "Unable to connect to (SSID)" pretty much instantly after clicking the network in Windows.

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: Unable To Connect To E3000 When Set To 5GHz

May 5, 2011

I've not been able to connect to my to Linksys E3000 when set to 5GHz "N" only Network mode.  Connections to the 5GHz can only be done in mixed mode.  I do not need to have A-Mode enabled, so I do not wish to use mixed.

View 4 Replies View Related

Linksys Wireless Router :: E4200 V2 - Acer 500 Unable To Connect / SSID Different

Feb 11, 2012

I am having trouble connecting my wireless devices to the e4200v2. My e4200v2 is connected to my action tec ver.F for fios. It's a LAN to LAN connection where the action tec is primary. I followed the directions changing the Secondary router address to 192.168.1.2 and the action tec stayed at 192.168.1.1. I also reset the action tec prior to any attachments (because I had an old belkin n+ connected). i also disabled DHCP in the secondary router. Both 5 & 2.4 Ghz have different passwords although I did try having them have the same password- no luck. I can't connect for whatever reason. Both network modes are mixed. On the action tec- the wireless is disabled. SSID are different. Can't connect for whatever reason. I am at a loss. I don't know if this is relevant- I use windows vista.

View 9 Replies View Related

Linksys Wireless Router :: Cisco E3000 / Change Guest Network Broadcast Ssid

Sep 7, 2011

i have a e3000 set up with my network i have guest network set up through the cisco connect but dont see a field to change the guest network broadcast ssid so an ideas?

View 1 Replies View Related

Linksys Wireless Router :: Unable To Access E3000 Via Https

Feb 29, 2012

I can not access my Linksys E3000 router via https://192.168.1.1.Before this mishap, I was able to gain access to my Linksys E3000 router via http://192.168.1.1 and/or the Cisco Connect software application on Windows 7. Yesterday, I went into my router's administration page and disabled http, and enabled https. I then closed out all browsers, restarted them and entered https://192.168.1.1
 
After that, I learned quickly I made a huge mistake to make these changes. I simply can not access my router admin wired or wirelessly. Accessing the internet works great, but router admin page is a no go.Firefox and IE states, "There is a problem with this website's security certificate." and was unable to proceed.Firefox even gave me the option to accept a security exemption to proceed, but that failed.
 
I have also tried using the Cisco Connect utility, and that also failed. I have taken these steps and not been able to access my router's admin page.I don't want to take the last final resort to reset my router and re-enter my settings again. I know I saved the router's backup file somewhere, but can't find it.Is there another way for me to gain access via https with http disabled? All I want to do now is go back in and change it back to enable http access.

View 9 Replies View Related

Linksys Wireless Router :: E3000 Unable To Configure All Features

Feb 18, 2011

I just picked up an e3000 last night.  Set up was performed manually.  Flashed to 1.0.04.  No issues and I was up in under 10 min.Although I read the user guide, prior to purchase, I admit I did not expect that I would not be able to configure ALL of the router's features and functions from the web based configuration, without using the CISCO Connect CD.Parental Controls and GUEST Access cannot be configured unless you load the Cisco Connect software.While this is not a huge deal, this implementation is clumsy and cumbersome for advanced users.  Honestly, I had no disire to install the Cisco Connect software.  I was further disappointed to see that it stores the router's password. 
 
My feeling here, let's not ruin a great thing.  There are two types of users.  One's who need a configuration wizard, and other's who don't.  I guess some inroads are being made in the right direction as some GUEST access functions can be made in the web gui on the e4200.  I hope this can be further expanded to all "e" series routers in the future. Overall, it works as advertised. Streaming 720p HD video over wireless 2.4Ghz band G only is flawless.  This is no different than my wrt54g2, but I'm upgrading to a 1080p player and have read that N on the 5Ghz band is the way to go.   

View 1 Replies View Related

Linksys Wireless Router :: E2500 Unable To See 5GHz Channel SSID

Jul 1, 2012

I've recently purchased the E2500, done the setup but am facing some issues.I'm unable to see the 5GHz channel SSID, I can only see the 2.4GHz channel SSID.Have tested all the laptops and devices at home and all can't see the 5GHz channel.The list of devices are:
 
a) iPhone 3GS
b) iPhone 4G
c) iPhone 4GS (some sites says it doesn't support, some says it does, I'm confused as a result)
d) Samsung laptop
e) Dell laptop
f) Momo11 Little Bird Edition tablet (Made in China [MIC])
g) No name MIC tablet
 
Secondly, is there any tips / tricks to tweak the modem to increase the internet speed?

View 1 Replies View Related

Linksys Wireless Router :: Unable To Extract Bin File For E3000 Firmware

Jun 4, 2012

PowerArchiver compression sw (newest version) does not recognize the file as valid archive

View 4 Replies View Related

Linksys Wireless Router :: E3000 - Unable To See Network Media Player

Jul 26, 2010

I am unable to see my network media player (wired CAT6 or wireless) using the SAMBA Share feature.  My UPNP works fine.  I do not have this issue when I am using the Linksys WRT54G or a Netgear WNDR3700 (I returned it to give the E3000 a try) - so I know all my share persmissions and device firewall is turned off.  How do I get it to work with the E3000?  I want to be able to transfer and stream media files to my media player using SAMBA.  Usually my network media player automatically detects SAMBA Servers/Devices and adds it to its list for me to access.  But when I use the E3000 that is not the case.

View 4 Replies View Related

Linksys Wireless Router :: Unable To Pull Up E3000 Storage Page?

Mar 13, 2013

It's been a while since I sent into my router and messed with any of the Storage setting. I recently decided to change things around so I recently went in the router and attempted to access the Storage page but all I get is a blank page with this address http://192.168.1.1/storage/Disk_Management.asp.

View 4 Replies View Related

Linksys Wireless Router :: E3000 - Unable To Write Files To USB Hard Drive

Jul 22, 2012

I bought a seagate USB hard drive today from Target.  Its a 2TB and I was going to use it via USB attached to my router.  I connected it and the Linksys firmware detected it and I was able to create the appropriate folders on the drive for storage through the linksys GUI.My issue is that I am now trying to move my movies and tv shows over to the drive and it isn't allowing me to do that. 
 
I get an error message that says "You don't have access to //myshare.  contact your administrator".
 
I'm not sure why I was able to create folders on this drive but am unable to move files to it.  Makes no sense to me.  Write permission is write permission no?My machine which currently stores the media files is windows7 utimate.  The router is E3000 using up to date stock firmware.

View 1 Replies View Related

Linksys Wireless Router :: E3000 Will Not Connect To Internet?

Aug 30, 2011

shows connection to cable modem, shows IP lease, able to renew and release lease. shows all DCHP clients, but does not allow internet to get through. tried cloning old routers MAC, no dice.

View 6 Replies View Related

Linksys Wireless Router :: E3000 Will Not Connect To Internet

Apr 16, 2010

I just purchased an E3000 to replace my WRT54G.I set up the E3000 through a wired connection from my Comcast modem to my desktop (running Windows 7).Through Cisco Connect, I was unable to connect to the internet. The desktop connects to the E3000 but the E3000 does not connect to the modem. I've tried to reset the E3000 and  power down both the E3000 and the modem yet I still cannot connect.I swapped my WRT54G back into place and my connection is fine while I figure this out.

View 4 Replies View Related

Linksys Wireless Router :: E3000 - How To Connect Nintendo DS

Feb 21, 2011

E3000 uses WPA secutiry...Nintendo DS ONLY works with WEP security.
 
Can I change my E3000 to WEP?  on a Nintendo support site per this issue, it says:
 
Routers using the Cisco Connect software default to WPA security, which is not compatible with online multiplayer with Nintendo DS Game Cards. To change your wireless security mode to WEP, you will need to use your router's web utility instead of Cisco Connect.
 
A) is that true

B) if so....HOW?
 
Bottom line, I NEED to be able to do this.  If it's not possible, than I made a very bad purchase decision & will never do so again

View 3 Replies View Related

Linksys Wireless Router :: Reset E3000 Now Can't Connect To Internet

Nov 1, 2011

i was having issues with one of my devices after a power outage.  all my other devices worked (laptops, xbox, iphones, etc)i thought doing a reset on the router would get the odd device working again but all it did was mess up my internet.  i don't have the key or cd any longer from when i set it up.

View 9 Replies View Related

Linksys Wireless Router :: Cisco Connect To E3000 That Is Not Primary

Nov 14, 2011

 My network is Cable modem -> RVS4000 (does my VPN) -> E3000 (does my wireless)Cisco connect seem to deal with this issue and I want to use the guest feature of the wireless.

View 1 Replies View Related

Linksys Wireless Router :: E3000 Setup Fails To Even Connect At All?

Apr 17, 2010

I have comcast Triple HD cable internet and I have been using a low end 5 year old Linksys Router.  I decided to upgrade and get the E3000.  So far I have had no luck at all getting it to work.  Setup fails to even connect at all.  I spent 2 hours on the phone with tech support.  There were in trying to get it up and running but we have been unable to get a TCP/IP number from my provider (comcast).  I hooked up the old router to see if any of my settings looked unusual but they seemed normal.

View 9 Replies View Related

Linksys Wireless Router :: E3000 - Cannot Connect To Internet On Laptop

Mar 25, 2013

I have a cable modem with an E3000 router, wired to my desktop. Internet connection is fine for my desktop, wired to Xbox, wifi for Iphone, Ipod, but no connectivity to my laptop wirelessly. I have run the repair automatically on my laptop (Windows 7) and get 2 different messages when trying over and over to use this tool. 1. Network Configuration Problem 2. Problem with wireless adapter or access point. I get a "fail" when trying this: 

1. If your client device has a Wi-Fi Protected Setup™ button,click or press that button and then click the button on the right. or when putting in the router's pin number.

View 4 Replies View Related

Linksys Wireless Router :: E3000 / Cisco Connect Software For MAC OSX 10.8.2

Nov 2, 2012

releasing Cisco Connest software for MAC OSX 10.8.2 Mine doesn't work anymore with the wireless Linksys router E3000

View 1 Replies View Related

Linksys Wireless Router :: E3000 / Cisco Connect Will Not Launch

Aug 31, 2011

I have Cisco Connect  and E3000 router running on Mac OSX 10.5.8. The router is working and I want to add another device, but when I try to start Cisco Connect, it starts to launch, but it stops and will not launch. The icon starts to appear on the Icon bar and then fades away. What should I do?

View 1 Replies View Related

Linksys Wireless Router :: Connect 24 Ports Switch With E3000?

Aug 23, 2011

I just bought a e3000 and I have a 24 ports switch. I would like to plug more than 8 pc...how do I proced ? I used to have a dlink router and just plug a cat5e from the dlint to the switch ... but it doesn't work with the e3000

View 5 Replies View Related

Linksys Wireless Router :: E3000 - Cannot Connect To Wifi Network

Aug 20, 2011

I have the E3000 router.  I set it up about a month ago and had my laptop and iphones and ipads all hooked up and working great.  About two weeks ago, all of my devices are having problems connecting to the network and if they do connect, it is unstable (slow speeds or constantly dropping from the network).  I know it is not the internet due to the fact that my LAN connection (hardwired) runs great.  I am pulling my hair out trying to figure out why.  I have restored to factory defauls and started over setting it up with no change in performance.   I have the latest drivers on the router and the laptop.  I thought maybe it was vista and my laptop or network card, but the fact that I cannot get my phones or ipads to connect with good performance I am starting to think it is something to do with the router.  Also, just for more info, I am using Chater cable internet.  I am running vista 64x on the laptop. 

View 1 Replies View Related

Linksys Wireless Router :: E3000 Cisco Connect And OpenDNS

Dec 22, 2010

I have been using OpenDNS for a long time, and I just got the Linksys E3000. When I tried to change the settings to add OpenDNS it said that some changes may cause the Cisco Connect software not to work anymore.
 
If I change the Static DNS 1 and 2 [URL] will I still be able to use all of the functions in the Cisco Connect software?

View 9 Replies View Related

Linksys Wireless Router :: Cannot Now Connect To E3000 Using Browser Utility

Apr 8, 2012

Not sure how I got here, but I cannot now connect to the E3000 using the Browser Utility. USing https://10.x.x.x, shows certificate warning page, then when I continue "Internet Explorer cannot display the webpage".DId NOT change the host hame.Last time I used the Browser Utility (weeks ago) was to disable the wireless to check something. Reenabled the wireless, no apparent problems until today when I tried to access via the Browser Utility.As I never ran Connect, there are no settings to change, and now it cannot detect the device.I guess I'll wait until I HAVE to change something, and do a 30-30-30 reset.

View 1 Replies View Related

Linksys Wireless Router :: E3000 Can't Connect To Internet Connection

Apr 7, 2011

I just bought a new E3000 router less than 2 weeks ago.  I spent hours with my tech guy setting up the router so that I was getting excellent internet speed and the connection between my computer and my nas was maximized.  In the process of setting up the router my laptop (Windows 7) and the basement laptop (Vista) were set up to access the router.  Both work perfectly.These are now the only two devices in the house that can get internet access.The other devices that should connect are:
 
-2 Laptops (both Vista)
-1 iPhone 4
-2 iPhone 3gs
-1 Printer
 
I can't get them to connect.  I spent an hour with a guy at Cisco tonight who just couldn't seem to get past the idea that it was not the laptop that was the problem.

View 9 Replies View Related

Linksys Wireless Router :: E2000 Wifi Ssid Disappears And Won't Connect

Jan 1, 2013

My 'main' Wifi SSID will just disappear and you can't connect to it.  the guest account will still show up.  computers/devices that are already connected will stay connected and will work fine, but anybody reconnecting will not be able to.  Only solution I've found so far is to unplug and replug in my router

View 1 Replies View Related

Linksys Wireless Router :: E1500 Not Broadcasting SSID / Can't Connect To Wire

Nov 10, 2011

So I have this E1500 Router that worked fine for the past 5 months, then out of the blue, the wireless feature ceased to function... laptops were not being able to connect to the wireless, the router was also not broadcasting the SSID.So, here's what I have done so far:

1. Check the router software settings, all was good there.

2. Did a "hardware reset" pushing the red button. (now this solved the problem, BUT only for a day, when power is turned off for the night, the next day it's non-functional again. The cycle can be repeated daily, but its a pain to reset and set it up everyday)

3. Updated the Firmware, and this somehow solved the problem for 3 Days... and now it's back to non-functional, again out of the Blue.
 
Is the Router just busted and it's not remembering the settings?

View 2 Replies View Related

Linksys Wireless Router :: E3000 Internet Comm Stopped Now Can't Connect?

Jul 6, 2011

Woke up this morning to the friendly 'No Internet access' message in the system tray. Thought it was the laptop but it wound up being the router (I guess).I can connect directly to internet via the cable modem (Comcast) but can't get a connection through the router.There are no IP addresses listed on the router admin page.Renew IP doesn't work.Everything was ok last night. I've had the router for a year or so and except for having to reset it every week or 2 for WiFi connection issues,it's worked pretty well.I soft-reset the router but then couldn't connect to 192.168.1.1.Hard-reset and still can't connect to 192.168.1.1.I do see connection lights. Just can't get to it. 

View 9 Replies View Related

Linksys Wireless Router :: Installed E3000 Now VPN Clients Could No Longer Connect

Nov 3, 2010

I had a simple PPTP VPN server running behind my old DLink router.  When I installed the E3000 the VPN clients could no longer connect.  The port forwarding for PPTP is turned on and VPN passthrough is enabled. The PPTP server reported GRE47 checksum failed.  The linksys chat tech was not beneficial.  How to get a PPTP route to work? 

View 5 Replies View Related

Linksys Wireless Router :: E3000 Cannot Access Admin Via Cisco Connect

Apr 25, 2012

I tried all methods: Cisco Connect (on Vista), http and https, but none works. However, the router seems function correctly. My laptop can acquire DHCP address and browse via the router. But I just cannot connect to the router to perform Admin tasks.Problem: when I launch CiscoConnect: the GUI shows "Cannot access your router", even though I am using the router to browse the net wirelessly and wirely. Using browser to navigate to http://192.168.1.1 and https://192.168.1.1 also give me cannot access error!

View 1 Replies View Related

Linksys Wireless Router :: E3000-EE Why Ping Is Rising When Connect To Internet

Nov 26, 2011

Connecting The Internet by Ethernet Lan-cable (without a router), ping to Yandex.ru is 4 ms. If we connect by router ping is 27 ms. If we ping by web-interface it is 4 ms. Connecting by Wi-Fi it is 27 ms.I' ve substituted the cable connected router and computer. So my questions are: why ping is rising when I connect to the Internet by router?

View 1 Replies View Related

Linksys Wireless Router :: E3000 Disconnected / Connect To PC Usb Port Directly

Jul 26, 2011

I have external hard drive connected to E3000. It is formatted as NTFS and working fine. However if I disconnect from router and connect to PC usb port directly, I get a message that hard drive needs to be formatted.

View 2 Replies View Related

Linksys Wireless Router :: E3000 - Cannot Connect Samsung CLP-315W Printer

Feb 11, 2011

Trying to connect a Samsung clp-315w wirelessly to my E3000. I plug the Ethernet cable into both to configure the printer and I cannot access the printer via its IP address. I suspect the printer is reporting the wrong IP address or it the IP is not being assigned by the router or it is being blocked by the router. Routers firewall is off. I use the Samsung software and it does not see the printer either. It seems the router is not seeing the printer or allowing it access to the network. Spent much time with a good Samsung support person and tried everything and narrowed the problem down to the router connection. Is there a setting on the router which needs to be changed to allow me to see the printer to configure it for wireless access?

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved