Linksys Wireless Router :: Unable To Access E3000 Via Https
Feb 29, 2012
I can not access my Linksys E3000 router via https://192.168.1.1.Before this mishap, I was able to gain access to my Linksys E3000 router via http://192.168.1.1 and/or the Cisco Connect software application on Windows 7. Yesterday, I went into my router's administration page and disabled http, and enabled https. I then closed out all browsers, restarted them and entered https://192.168.1.1
After that, I learned quickly I made a huge mistake to make these changes. I simply can not access my router admin wired or wirelessly. Accessing the internet works great, but router admin page is a no go.Firefox and IE states, "There is a problem with this website's security certificate." and was unable to proceed.Firefox even gave me the option to accept a security exemption to proceed, but that failed.
I have also tried using the Cisco Connect utility, and that also failed. I have taken these steps and not been able to access my router's admin page.I don't want to take the last final resort to reset my router and re-enter my settings again. I know I saved the router's backup file somewhere, but can't find it.Is there another way for me to gain access via https with http disabled? All I want to do now is go back in and change it back to enable http access.
View 9 Replies
ADVERTISEMENT
Oct 12, 2012
This problem just started. I am unable to load certain https sites (for work). If i directly connect to ethernet, it works, so my isp isnt my problem. When i try to connect to the sites, it says "sending request" then times out. I have played around with the settings non stop and nothing has worked. I have a mac running 10.7.5.
View 3 Replies
View Related
Jul 13, 2012
I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
View 6 Replies
View Related
Oct 9, 2011
I've had my E3000 for almost a year now and it's been great - until recently. Latencies have become patchy for some users and most surprisingly, the 5GHz network has stopped using two channels. I did a 30/30/30 reset on it a few minutes ago and re-configured the whole thing. It's set to use 40MHz Only and WPA2 Personal, but speeds at the physical layer are still just 144 Mbps and in the web interface's Status page it clearly says "20 MHz".
Why might this be? It was fine for so long, only to refuse to use two channels now. I've checked what the other wireless networks in my area are like, and none of them are even 5GHz-capable as far as I can tell, so the relevant spectrum shouldn't be overcrowded. It's rather nice to have the two channels for NAS transfers and streaming and such.
After manually specifying a base channel (48 at the moment), it actually kicks into 40MHz. The problem is now that my clients, both using a WUSB600N, are getting "Unable to connect to (SSID)" pretty much instantly after clicking the network in Windows.
View 1 Replies
View Related
May 5, 2011
I've not been able to connect to my to Linksys E3000 when set to 5GHz "N" only Network mode. Connections to the 5GHz can only be done in mixed mode. I do not need to have A-Mode enabled, so I do not wish to use mixed.
View 4 Replies
View Related
Feb 18, 2011
I just picked up an e3000 last night. Set up was performed manually. Flashed to 1.0.04. No issues and I was up in under 10 min.Although I read the user guide, prior to purchase, I admit I did not expect that I would not be able to configure ALL of the router's features and functions from the web based configuration, without using the CISCO Connect CD.Parental Controls and GUEST Access cannot be configured unless you load the Cisco Connect software.While this is not a huge deal, this implementation is clumsy and cumbersome for advanced users. Honestly, I had no disire to install the Cisco Connect software. I was further disappointed to see that it stores the router's password.
My feeling here, let's not ruin a great thing. There are two types of users. One's who need a configuration wizard, and other's who don't. I guess some inroads are being made in the right direction as some GUEST access functions can be made in the web gui on the e4200. I hope this can be further expanded to all "e" series routers in the future. Overall, it works as advertised. Streaming 720p HD video over wireless 2.4Ghz band G only is flawless. This is no different than my wrt54g2, but I'm upgrading to a 1080p player and have read that N on the 5Ghz band is the way to go.
View 1 Replies
View Related
Jan 28, 2012
To improve the security of my 4200 v1 router, I turned on in the router configuration "Access via HTTPS" and after the reboot I could not access my router via the browser even when I click on the browser message to continue. What do I need to configure either in the router or my browser to use HTTPS?
View 9 Replies
View Related
Jun 4, 2012
PowerArchiver compression sw (newest version) does not recognize the file as valid archive
View 4 Replies
View Related
Jul 26, 2010
I am unable to see my network media player (wired CAT6 or wireless) using the SAMBA Share feature. My UPNP works fine. I do not have this issue when I am using the Linksys WRT54G or a Netgear WNDR3700 (I returned it to give the E3000 a try) - so I know all my share persmissions and device firewall is turned off. How do I get it to work with the E3000? I want to be able to transfer and stream media files to my media player using SAMBA. Usually my network media player automatically detects SAMBA Servers/Devices and adds it to its list for me to access. But when I use the E3000 that is not the case.
View 4 Replies
View Related
Mar 13, 2013
It's been a while since I sent into my router and messed with any of the Storage setting. I recently decided to change things around so I recently went in the router and attempted to access the Storage page but all I get is a blank page with this address http://192.168.1.1/storage/Disk_Management.asp.
View 4 Replies
View Related
Feb 16, 2012
I was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
View 6 Replies
View Related
Jul 22, 2012
I bought a seagate USB hard drive today from Target. Its a 2TB and I was going to use it via USB attached to my router. I connected it and the Linksys firmware detected it and I was able to create the appropriate folders on the drive for storage through the linksys GUI.My issue is that I am now trying to move my movies and tv shows over to the drive and it isn't allowing me to do that.
I get an error message that says "You don't have access to //myshare. contact your administrator".
I'm not sure why I was able to create folders on this drive but am unable to move files to it. Makes no sense to me. Write permission is write permission no?My machine which currently stores the media files is windows7 utimate. The router is E3000 using up to date stock firmware.
View 1 Replies
View Related
Mar 8, 2012
When accessing the E3200 router using then ERROR 501.Not Implemented.That method is not implemented. The error occured after enabling the "Local Management Access, Access via: HTTPS" option on the Administration > Management tab.I tried different browsers FireFox (version 10), Internet Explorer (version 8,9), the same error was displayed and no acces granted to the E3200 router. I reseted the router and tried the latest firmware 1.0.03 build 9 Feb 1, 2012, but after enablib the option the issue occured again and it is not possible to connect to the router.
View 9 Replies
View Related
Mar 1, 2012
I have a Cisco RV082 and I would like to connect my E3000 to it and use it as just a wireless access point. Is it possible to do this with the E3000 so the RV082 is providing the routing functionality?
View 1 Replies
View Related
Jun 11, 2011
I am using firmware version 1.0.04 build 6.I am having a few issues viewing the log; the incoming, outgoing and security logs are completely blank, the DHCP log is the only one populated.Even though it's populated, the time stamp displays the date as Jan 1 1970, time appears fine if I use UDT (Time is set to Mountain), the Router Status correctly displays the current time for my location.I vaguely remember the other logs worked with a previous firmware 1.0.03? Don't recall if the Date Time stamp was working correctly.
View 2 Replies
View Related
Jul 25, 2011
I have comcast cable and a Linksys E3000 that has been pretty reliable. I have a website that I use to send some information to. Friday morning was the last time I could connect to this page. I cannot hit it via web, ssh, or ftp or ping. I can view it at work and on my 3g internet. But no more from home. I have determined that it has to be the router (straight connection into cable modem and I'm in). I've reboot the router and even restored to factory spec, neither works.
View 1 Replies
View Related
Feb 22, 2012
I have access restrictions set up for certain wireless devices in my home that the kids use to kick them off at 11 pm and keep them off all night. where I am running into a problem is I want to block these same devices from downloading anything without my permission my son downloads everything he sees, Comcat has already threatened to kick us off their service if we go over 250 gb bandwidth use in a month again. so I want to configure something in the router that will block all downloads for specific wireless devices. with the access restrictions I have set up I used the mac address not just the ip so they have no way around it I constantly monitor what is connected. I am using the stock firmware as well
View 1 Replies
View Related
Apr 19, 2010
I replaced my old Linksys WRT54G wireless router with the new E3000 wireless router. The installation was a breeze, but not what followed henceforth. I was able to access the internet on my wireless desktop/laptop/Netflix ROKU player/WD TV live media player, but lost access to all the network shares. I spent a lot of useless time with Linksys chat support and phone support, where they said their responsibility is only getting the internet working. They said they are not responsible for file and printer sharing issues, and suggested I use a third-party paid support package to resolve my issues. Over and above spending a hefty amount for the lates top of the line E3000 router, I was not going to shell out additional money for support.
Thinking that it could probably be due to some Windows XP firewall/anti-virus (McAfee) issues, I disconnected the E3000 and connected the old WRT54G back again. Lo and behold, everything started working fine again. I could access the shared folders of my desktop (to which my router is attached) and printer, from the wireless laptop/desktop/media player just as before without any problems. I then switched back to the E3000 and lost the shares again. So I have come to the conclusion, there is definitely some setting within the E3000 that is preventing the file and printer sharing. I just can't figure out what it could be, and am at a point of returning it back to the store as defective. The extra N-speed is useless to me if my devices can't access the network shared content.Also, I tried to set up the UPnP media server feature of the E3000 by attaching USB storage and configuring it via the Linksys web based utility, but my media player is unable to access the content.
View 9 Replies
View Related
Jul 10, 2010
I have my router setup fine to the internet, as well as the media server. I can't figure out how to access the hard drive from my laptop, however. The manual says put 192.168.1.1 in the address field of windows explorer, but it just gives me the "Setup" page for the router.
View 9 Replies
View Related
Jan 14, 2011
I have an e300 router with my external hdd connected via the USB port. I am trying to figure out how to access the hdd remotely. I am not trying to get to it through remote desktop access. I have my laptop that I take with me when away from home but I would like to be able to access the hdd via Internet.
View 4 Replies
View Related
Jun 14, 2011
I needed the Guest access of wi-fi setup that LinkSysys routers provided. I don't need the router/modem i just want to have wi-fi access point. I'm an advanced user and i can work with manual setup etc.I tried to do a manual setup of the router, i changed the IP address to mask my network and enable wi-fi and worked BUT the guest access option is NOT available unless you use the stupid CISCO connect software.
Now the cisco connect software IS NOT working or complete the setup if you don't connect it through the router and gain Internet access which is IMPOSSIBLE for me to accomplish as my modem is connected to a firewall device and we are using static DSL options with PPPoE and usernameme/password. There is no way i can get cisco connect to load properly as it always "fixes my connection trying to gain Internet access".Is there any solution on manually properly setup this router and take full advantages of it capabilities or should i return it ?
View 7 Replies
View Related
Dec 8, 2011
I have an E3000 Dual Band. Currently, I have 3 laptops and two 360s on our network. They work fine. Up until last week so did my other kid's computers. They came home from college and attempted to get on our network unsuccessfully. In their network and sharing center, both their computers say under view your active networks: unidentified network (public network). Access type: No network access. Connections: has the correct network name information. When they attempt to access the network with the correct password, they show 4 bars of reception and a message of limited access (along with the above message). I did a little checking and found that our router info differs from their auto configuration. Our IPv4 starts with 192 not 169 like thiers. Also, the subnet masks are different. Also, they have no info in the IPv4 default Gateway, IPv4 DNS Server, and IPv4 WINS Server. Finally, my wife tried to acces the network with an ebook reader. It shows secured WPA2, but won't access it.
View 2 Replies
View Related
Sep 23, 2011
Internet policy access on my Linksys E3000. I am trying to block facebook.com to a particular ip address in my office. This what I did. Logged in to control panel clicked on access restriction. Clicked on add. Gave it a name. Clicked the applies to drop down box and selected by ip address. Unchecked the block all internet access. Typed facebook down in the window below. Saved.Not blocking access.
View 9 Replies
View Related
Feb 24, 2011
I can now access my router config pages when connected to my ATT router. However, I cannot seem to access the Internet when connected to my e3000; I just time out. I also have difficulties just connecting to my e300 for some reason. I have been connected a couple of times where i could access the Internet but it was only for a few minutes and it was very slow.I can't seem to put the router in the DMZ because the ATT router will only DMZ a DHCP-enabled device and the e3000 has a static IP (192.168.1.253). I have tried running the PING and Traceroute diagnostics and both just come back with Unknown Host no matter what URL i enter. The status page also appears as if the e3000 is not properly talking to the ATT router. Under the Internet Connection area it shows Connection Type: Automatic Configuration - DHCP then 0s for IP address, subnet, and gateway. the DNS entries are empty and the MTU shows 1500 and the DHCP Lease Time is also empty. i am all ears and willing to try whatever. But i just want to be able to connect to my e3000 so i can utilize the wireless n internally and connect a 2TB external drive to share. But I also want to be able to get out to the Internet when i am connected to the device.
View 6 Replies
View Related
Jan 26, 2012
For a while now I've been thinking of setting up a (hopefully) secure remote access from a location outside of my local network. Since I'm going to be away from where I usually live for about six months due to the location of my Course that I'm going to study, I want to be able to remotely access the router if something were to happen. Up until this point, I've been doing the management through a Teamviewer 6/7 remote access with my home computer and connecting from the inside IP address (Example: 192.168.1.1), but it's going to be taken away so I wouldn't be able to do that this year. Is it possible to set up a secure telnet on a Linksys E3000 Wireless Unit that way I can control it through Command Prompt, or would I have to set up Remote Management Access to use the unit outside the network through programs like Internet Explorer or Mozilla Firefox?
View 1 Replies
View Related
Jul 30, 2011
Using Cisco Connest I set up a password for guest access. It will function for a time then suddenly become insecure. Sometimes it will function for a month, sometimes a week. I have to reset the Unit to factory defaults each time and began again.
View 3 Replies
View Related
Mar 2, 2012
I have had numerous issues with my E3000 since I got about two months ago and they have all been resolved with the exception of this new one that popped up today.
My Samsung Blu-ray player is connected firectly via ethernet cable to the router. When it's on, I lose all conenctivity to the router with my wireless devices including three PC's, a PS3, two iPhones, one iPad, one Samsung Smart TV, one XBOX 360 and an Onkyo Receiver. When I say that I lose connectivity, I don't mean that I lose access to the Internet. My PC's see the network but cannot connect to it, the same goes for the Apple devices. The moment I shut off the Samsung BD player it kicks right back on and works normally. Until today, this never occurred.
I contacted Tech Support and they had never heard of this happening before. They suggested that I change the ethernet cable which I did while the unit was on and it worked until I turned the BD player off and turned it back on again. I also tried switching ports to no avail. Alos all of the software is up to date on both the router and the BD player.
View 3 Replies
View Related
Dec 30, 2012
I switched from comcast to att uverse. I was happy about the guest-access feature of E3000 when using the comcast, where I can directly connect my e3000 to the modem (basically you can see two network, one is XXX, the other is XXX-guest). However, the ATT uverse has a gateway that combines the modem and router together, in order to use my e3000 instead of the built-in router of the gateway, I have done a LAN-to-LAN connection and I can access internet without any problem. But in this case, I can not enable my guest-access feature. When I use Cisco Connect to set up e3000, it says "cannot connect to your router". how to set up the guess-access feature of e3000 when using ATT uverse.
View 3 Replies
View Related
Feb 29, 2012
I just purchased an E-3000 and when I log into the user interface it seems changing pages and saving settings takes forever. I click on a section in the router menu and it takes what seems like 30 seconds for the page to change or accept the new settings. It's not my browser it's definitely a Linksys Router issue. I updated to the latest firmware and latest Cisco Connect software as well. Is this slow user interface a normal thing with these routers?
View 1 Replies
View Related
Apr 25, 2012
I tried all methods: Cisco Connect (on Vista), http and https, but none works. However, the router seems function correctly. My laptop can acquire DHCP address and browse via the router. But I just cannot connect to the router to perform Admin tasks.Problem: when I launch CiscoConnect: the GUI shows "Cannot access your router", even though I am using the router to browse the net wirelessly and wirely. Using browser to navigate to http://192.168.1.1 and https://192.168.1.1 also give me cannot access error!
View 1 Replies
View Related
Jul 8, 2011
We have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.
View 1 Replies
View Related
Jul 24, 2011
I want to use my WRT160n in my room to connect all my devices (Xbox, playstation 3, and 3 laptops) I hardwired the E3000 from the room downstairs thats connected to everything else.
View 2 Replies
View Related
Dec 31, 2012
Within the Internet Access Policy section of the browser based utility, is it possible to limit access for a specific device (PC) to LAN only (not allow any traffic to external internet)? I see that you can block internet access for a specific machine, however I didn't know if this was inclusive of LAN as well.If not, is there another way to achieve this via the E3000 or should I be looking for a solution on the specific PC itself?
View 4 Replies
View Related
