Linksys Wireless Router :: E3000 Lose Access To Internet
Mar 2, 2012
I have had numerous issues with my E3000 since I got about two months ago and they have all been resolved with the exception of this new one that popped up today.
My Samsung Blu-ray player is connected firectly via ethernet cable to the router. When it's on, I lose all conenctivity to the router with my wireless devices including three PC's, a PS3, two iPhones, one iPad, one Samsung Smart TV, one XBOX 360 and an Onkyo Receiver. When I say that I lose connectivity, I don't mean that I lose access to the Internet. My PC's see the network but cannot connect to it, the same goes for the Apple devices. The moment I shut off the Samsung BD player it kicks right back on and works normally. Until today, this never occurred.
I contacted Tech Support and they had never heard of this happening before. They suggested that I change the ethernet cable which I did while the unit was on and it worked until I turned the BD player off and turned it back on again. I also tried switching ports to no avail. Alos all of the software is up to date on both the router and the BD player.
I have been using a Linksys E3000 router for a few months now. Love it. But this last week, when ever I wake my monitor up after it's power saving mode kicks in, I lose my internet connection for about 15 seconds. If you look at the router before the monitor is on, I am connected. The light is on for port 1. But as soon as my monitor gets turned back on, it light just turns off and will reconnect after about 15 seconds. I've looked it up online and can only find things about when the entire system wakes up, and usually those people have to reboot their entire system to get a connection again, or turn the router off then back on. Using Windows 7?
Internet policy access on my Linksys E3000. I am trying to block facebook.com to a particular ip address in my office. This what I did. Logged in to control panel clicked on access restriction. Clicked on add. Gave it a name. Clicked the applies to drop down box and selected by ip address. Unchecked the block all internet access. Typed facebook down in the window below. Saved.Not blocking access.
I can now access my router config pages when connected to my ATT router. However, I cannot seem to access the Internet when connected to my e3000; I just time out. I also have difficulties just connecting to my e300 for some reason. I have been connected a couple of times where i could access the Internet but it was only for a few minutes and it was very slow.I can't seem to put the router in the DMZ because the ATT router will only DMZ a DHCP-enabled device and the e3000 has a static IP (192.168.1.253). I have tried running the PING and Traceroute diagnostics and both just come back with Unknown Host no matter what URL i enter. The status page also appears as if the e3000 is not properly talking to the ATT router. Under the Internet Connection area it shows Connection Type: Automatic Configuration - DHCP then 0s for IP address, subnet, and gateway. the DNS entries are empty and the MTU shows 1500 and the DHCP Lease Time is also empty. i am all ears and willing to try whatever. But i just want to be able to connect to my e3000 so i can utilize the wireless n internally and connect a 2TB external drive to share. But I also want to be able to get out to the Internet when i am connected to the device.
We have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.
I have an E1550 less than 1 year old. Lately, I have been losing internet on the AT&T modem. I called AT&T but as part of their diagnostics, I have to plug the modem directly into the PC. I have loaded the latest firmware to the E1550.Lose Internet but wireless connectivity to router exists.Internet light on modem is out (modem is connected to router)Unplug modem and leave off plug in, internet light is still out.Unplug router, plug router back in - no internet connection but do have wireless connectivity to router.Take cable from modem to router and plug directly into PC internet light comes on in modem and I have internet from PC.Take cable from PC and plug back into router .I have internet via wireless.What I can't figure out is what could be happening in router that would impact modem internet connection. I have replicated this at least 3 times. Yes, the modem is a bit old, but since plugging it directly into the PC works, I'm thinking it has to be the router and I cannot figure out why unless there's some sort of electrical thing going on in the router.
I have a disconnecting problem with my WRT120N (Linksys) wireless router. Sometimes all wireless devices lose the connection to the internet, and the access to the router administration page (192.168.1.1) becomes impossible. In this case LEDs of power, internet and wireless are lighting without flashing. This problem usually occurs every 48 hour, and there was no way to make a reconnection except turning the router off by unplugging the power wire and plug it again…
I hope find a solution for this problem here
Other question: are there any problems in Firmware Version: v1.0.04
I have a RV042:Firmware Version : v4.0.0.07-tm (Aug 19 2010 19:19:50)PID VID : RV042 V03 .Configured with a internal LAN address (10.0.17.0/24) and ISP PPPoE External address on WAN1.I´ve configured a VPN with a remote location (Fortigate 4) and after the VPN starts up the RV042 cannot ping any machine in their local network (using the diagnostic, all pings failed in 10.0.17.0/24) and no machines in that network can PING and access or manage the RV042
The only way to manage the RV042 after VPN starts UP is using a machine in the other side of the VPN (The Main office)If i force the VPN down, the connectivity begins to work, but as soon the VPN starts up again, the local/LAN connectivity loses again.
I have a Cisco RV082 and I would like to connect my E3000 to it and use it as just a wireless access point. Is it possible to do this with the E3000 so the RV082 is providing the routing functionality?
I am using firmware version 1.0.04 build 6.I am having a few issues viewing the log; the incoming, outgoing and security logs are completely blank, the DHCP log is the only one populated.Even though it's populated, the time stamp displays the date as Jan 1 1970, time appears fine if I use UDT (Time is set to Mountain), the Router Status correctly displays the current time for my location.I vaguely remember the other logs worked with a previous firmware 1.0.03? Don't recall if the Date Time stamp was working correctly.
I have comcast cable and a Linksys E3000 that has been pretty reliable. I have a website that I use to send some information to. Friday morning was the last time I could connect to this page. I cannot hit it via web, ssh, or ftp or ping. I can view it at work and on my 3g internet. But no more from home. I have determined that it has to be the router (straight connection into cable modem and I'm in). I've reboot the router and even restored to factory spec, neither works.
I have access restrictions set up for certain wireless devices in my home that the kids use to kick them off at 11 pm and keep them off all night. where I am running into a problem is I want to block these same devices from downloading anything without my permission my son downloads everything he sees, Comcat has already threatened to kick us off their service if we go over 250 gb bandwidth use in a month again. so I want to configure something in the router that will block all downloads for specific wireless devices. with the access restrictions I have set up I used the mac address not just the ip so they have no way around it I constantly monitor what is connected. I am using the stock firmware as well
I replaced my old Linksys WRT54G wireless router with the new E3000 wireless router. The installation was a breeze, but not what followed henceforth. I was able to access the internet on my wireless desktop/laptop/Netflix ROKU player/WD TV live media player, but lost access to all the network shares. I spent a lot of useless time with Linksys chat support and phone support, where they said their responsibility is only getting the internet working. They said they are not responsible for file and printer sharing issues, and suggested I use a third-party paid support package to resolve my issues. Over and above spending a hefty amount for the lates top of the line E3000 router, I was not going to shell out additional money for support.
Thinking that it could probably be due to some Windows XP firewall/anti-virus (McAfee) issues, I disconnected the E3000 and connected the old WRT54G back again. Lo and behold, everything started working fine again. I could access the shared folders of my desktop (to which my router is attached) and printer, from the wireless laptop/desktop/media player just as before without any problems. I then switched back to the E3000 and lost the shares again. So I have come to the conclusion, there is definitely some setting within the E3000 that is preventing the file and printer sharing. I just can't figure out what it could be, and am at a point of returning it back to the store as defective. The extra N-speed is useless to me if my devices can't access the network shared content.Also, I tried to set up the UPnP media server feature of the E3000 by attaching USB storage and configuring it via the Linksys web based utility, but my media player is unable to access the content.
I have my router setup fine to the internet, as well as the media server. I can't figure out how to access the hard drive from my laptop, however. The manual says put 192.168.1.1 in the address field of windows explorer, but it just gives me the "Setup" page for the router.
I have an e300 router with my external hdd connected via the USB port. I am trying to figure out how to access the hdd remotely. I am not trying to get to it through remote desktop access. I have my laptop that I take with me when away from home but I would like to be able to access the hdd via Internet.
I needed the Guest access of wi-fi setup that LinkSysys routers provided. I don't need the router/modem i just want to have wi-fi access point. I'm an advanced user and i can work with manual setup etc.I tried to do a manual setup of the router, i changed the IP address to mask my network and enable wi-fi and worked BUT the guest access option is NOT available unless you use the stupid CISCO connect software.
Now the cisco connect software IS NOT working or complete the setup if you don't connect it through the router and gain Internet access which is IMPOSSIBLE for me to accomplish as my modem is connected to a firewall device and we are using static DSL options with PPPoE and usernameme/password. There is no way i can get cisco connect to load properly as it always "fixes my connection trying to gain Internet access".Is there any solution on manually properly setup this router and take full advantages of it capabilities or should i return it ?
I have an E3000 Dual Band. Currently, I have 3 laptops and two 360s on our network. They work fine. Up until last week so did my other kid's computers. They came home from college and attempted to get on our network unsuccessfully. In their network and sharing center, both their computers say under view your active networks: unidentified network (public network). Access type: No network access. Connections: has the correct network name information. When they attempt to access the network with the correct password, they show 4 bars of reception and a message of limited access (along with the above message). I did a little checking and found that our router info differs from their auto configuration. Our IPv4 starts with 192 not 169 like thiers. Also, the subnet masks are different. Also, they have no info in the IPv4 default Gateway, IPv4 DNS Server, and IPv4 WINS Server. Finally, my wife tried to acces the network with an ebook reader. It shows secured WPA2, but won't access it.
I can not access my Linksys E3000 router via https://192.168.1.1.Before this mishap, I was able to gain access to my Linksys E3000 router via http://192.168.1.1 and/or the Cisco Connect software application on Windows 7. Yesterday, I went into my router's administration page and disabled http, and enabled https. I then closed out all browsers, restarted them and entered https://192.168.1.1
After that, I learned quickly I made a huge mistake to make these changes. I simply can not access my router admin wired or wirelessly. Accessing the internet works great, but router admin page is a no go.Firefox and IE states, "There is a problem with this website's security certificate." and was unable to proceed.Firefox even gave me the option to accept a security exemption to proceed, but that failed.
I have also tried using the Cisco Connect utility, and that also failed. I have taken these steps and not been able to access my router's admin page.I don't want to take the last final resort to reset my router and re-enter my settings again. I know I saved the router's backup file somewhere, but can't find it.Is there another way for me to gain access via https with http disabled? All I want to do now is go back in and change it back to enable http access.
For a while now I've been thinking of setting up a (hopefully) secure remote access from a location outside of my local network. Since I'm going to be away from where I usually live for about six months due to the location of my Course that I'm going to study, I want to be able to remotely access the router if something were to happen. Up until this point, I've been doing the management through a Teamviewer 6/7 remote access with my home computer and connecting from the inside IP address (Example: 192.168.1.1), but it's going to be taken away so I wouldn't be able to do that this year. Is it possible to set up a secure telnet on a Linksys E3000 Wireless Unit that way I can control it through Command Prompt, or would I have to set up Remote Management Access to use the unit outside the network through programs like Internet Explorer or Mozilla Firefox?
Using Cisco Connest I set up a password for guest access. It will function for a time then suddenly become insecure. Sometimes it will function for a month, sometimes a week. I have to reset the Unit to factory defaults each time and began again.
just bought an e3000 and want to use it with wireless internet- usb modem. when setting up it wouldnt go any further than the 'searching for connection' page as it couldnt detect a connection in the 'internet' lan (wan?) port.can i set it up to accept the wireless usb modem?
I switched from comcast to att uverse. I was happy about the guest-access feature of E3000 when using the comcast, where I can directly connect my e3000 to the modem (basically you can see two network, one is XXX, the other is XXX-guest). However, the ATT uverse has a gateway that combines the modem and router together, in order to use my e3000 instead of the built-in router of the gateway, I have done a LAN-to-LAN connection and I can access internet without any problem. But in this case, I can not enable my guest-access feature. When I use Cisco Connect to set up e3000, it says "cannot connect to your router". how to set up the guess-access feature of e3000 when using ATT uverse.
I just purchased an E-3000 and when I log into the user interface it seems changing pages and saving settings takes forever. I click on a section in the router menu and it takes what seems like 30 seconds for the page to change or accept the new settings. It's not my browser it's definitely a Linksys Router issue. I updated to the latest firmware and latest Cisco Connect software as well. Is this slow user interface a normal thing with these routers?
I tried all methods: Cisco Connect (on Vista), http and https, but none works. However, the router seems function correctly. My laptop can acquire DHCP address and browse via the router. But I just cannot connect to the router to perform Admin tasks.Problem: when I launch CiscoConnect: the GUI shows "Cannot access your router", even though I am using the router to browse the net wirelessly and wirely. Using browser to navigate to http://192.168.1.1 and https://192.168.1.1 also give me cannot access error!
Within the Internet Access Policy section of the browser based utility, is it possible to limit access for a specific device (PC) to LAN only (not allow any traffic to external internet)? I see that you can block internet access for a specific machine, however I didn't know if this was inclusive of LAN as well.If not, is there another way to achieve this via the E3000 or should I be looking for a solution on the specific PC itself?
I have an E3000 that I am just setting up.I have two issues:
1> I am replacing a WRT110. I had the old router set with a static IP address supplied by my ISP. I configured the E3000 with the same address and I cannot access the internet. Are there any tricks to setting this up on an E3000?
2> As configured I there is a guest network setup. BUT when I access the router I don't see the tab to be able to configure it.
I just purchased an E3000 to replace my WRT54G.I set up the E3000 through a wired connection from my Comcast modem to my desktop (running Windows 7).Through Cisco Connect, I was unable to connect to the internet. The desktop connects to the E3000 but the E3000 does not connect to the modem. I've tried to reset the E3000 and power down both the E3000 and the modem yet I still cannot connect.I swapped my WRT54G back into place and my connection is fine while I figure this out.
I have been running some test to see what I can do for speed to the interenet and NAS drive.I have a NIC card (1394) and the max connection I get is 400 Mbps. The card is suppose to be 10/100/1000 card and E3000 is the same... so why can't I connect at 1000?Max transfer I get to my NAS is 64-80 Mbps. Is there any way I can get this to be faster? I have a 1TB western digital drive attached.If I went with a NAS system like a Synology BYOD system could I get faster speeds for transfers if the NIC on the system was a 10/100/1000?`