Linksys Wireless Router :: Logging Access In E3000

Jun 11, 2011

I am using firmware version 1.0.04 build 6.I am having a few issues viewing the log; the incoming, outgoing and security logs are completely blank, the DHCP log is the only one populated.Even though it's populated, the time stamp displays the date as Jan 1 1970, time appears fine if I use UDT (Time is set to Mountain), the Router Status correctly displays the current time for my location.I vaguely remember the other logs worked with a previous firmware 1.0.03? Don't recall if the Date Time stamp was working correctly.

View 2 Replies


ADVERTISEMENT

Linksys Wireless Router :: Using E3000 Just As Access Point?

Mar 1, 2012

I have a Cisco RV082 and I would like to connect my E3000 to it and use it as just a wireless access point.  Is it possible to do this with the E3000 so the RV082 is providing the routing functionality?

View 1 Replies View Related

Linksys Wireless Router :: E3000 - Cannot Access Website

Jul 25, 2011

I have comcast cable and a Linksys E3000 that has been pretty reliable.  I have a website that I use to send some information to.  Friday morning was the last time I could connect to this page.   I cannot hit it via web, ssh, or ftp or ping.  I can view it at work and on my 3g internet.  But no more from home.  I have determined that it has to be the router (straight connection into cable modem and I'm in).  I've reboot the router and even restored to factory spec, neither works.

View 1 Replies View Related

Linksys Wireless Router :: E3000 Access Restrictions?

Feb 22, 2012

I have access restrictions set up for certain wireless devices in my home that the kids use to kick them off at 11 pm and keep them off all night. where I am running into a problem is I want to block these same devices from downloading anything without my permission  my son downloads everything he sees, Comcat has already threatened to kick us off their service if we go over 250 gb bandwidth use  in a  month again. so I want to configure something in the router that will block all downloads for specific wireless devices. with the access restrictions I have set up I used the mac address not just the ip so they have no way around it I constantly monitor what is connected. I am using the stock firmware as well

View 1 Replies View Related

Linksys Wireless Router :: Can't Access Network Shares With E3000

Apr 19, 2010

I replaced my old Linksys WRT54G wireless router with the new E3000 wireless router. The installation was a breeze, but not what followed henceforth. I was able to access the internet on my wireless desktop/laptop/Netflix ROKU player/WD TV live media player, but lost access to all the network shares. I spent a lot of useless time with Linksys chat support and phone support, where they said their responsibility is only getting the internet working. They said they are not responsible for file and printer sharing issues, and suggested I use a third-party paid support package to resolve my issues. Over and above spending a hefty amount for the lates top of the line E3000 router, I was not going to shell out additional money for support.
 
Thinking that it could probably be due to some Windows XP firewall/anti-virus (McAfee) issues, I disconnected the E3000 and connected the old WRT54G back again. Lo and behold, everything started working fine again. I could access the shared folders of my desktop (to which my router is attached) and printer, from the wireless laptop/desktop/media player just as before without any problems. I then switched back to the E3000 and lost the shares again. So I have come to the conclusion, there is definitely some setting within the E3000 that is preventing the file and printer sharing. I just can't figure out what it could be, and am at a point of returning it back to the store as defective. The extra N-speed is useless to me if my devices can't access the network shared content.Also, I tried to set up the UPnP media server feature of the E3000 by attaching USB storage and configuring it via the Linksys web based utility, but my media player is unable to access the content.

View 9 Replies View Related

Linksys Wireless Router :: Access SB Hard Drive On E3000?

Jul 10, 2010

I have my router setup fine to the internet, as well as the media server.  I can't figure out how to access the hard drive from my laptop, however.  The manual says put 192.168.1.1 in the address field of windows explorer, but it just gives me the "Setup" page for the router. 

View 9 Replies View Related

Linksys Wireless Router :: E3000 Remote External Hdd Access

Jan 14, 2011

I have an e300 router with my external hdd connected via the USB port. I am trying to figure out how to access the hdd remotely. I am not trying to get to it through remote desktop access. I have my laptop that I take with me when away from home but I would like to be able to access the hdd via Internet.

View 4 Replies View Related

Linksys Wireless Router :: Can E3000 Work As Access Point Only

Jun 14, 2011

I needed the Guest access of wi-fi setup that LinkSysys routers provided. I don't need the router/modem i just want to have wi-fi access point. I'm an advanced user and i can work with manual setup etc.I tried to do a manual setup of the router, i changed the IP address to mask my network and enable wi-fi and worked BUT the guest access option is NOT available unless you use the stupid CISCO connect software.
 
Now the cisco connect software IS NOT working or complete the setup if you don't connect it through the router and gain Internet access which is IMPOSSIBLE for me to accomplish as my modem is connected to a firewall device and we are using static DSL options with PPPoE and usernameme/password. There is no way i can get cisco connect to load properly as it always "fixes my connection trying to gain Internet access".Is there any solution on manually properly setup this router and take full advantages of it capabilities or should i return it ?

View 7 Replies View Related

Linksys Wireless Router :: E3000 Limited Access Of Network

Dec 8, 2011

I have an E3000 Dual Band.  Currently, I have 3 laptops and two 360s on our network. They work fine. Up until last week so did my other kid's computers.  They came home from college and attempted to get on our network unsuccessfully.  In their network and sharing center, both their computers say under view your active networks: unidentified network (public network). Access type: No network access. Connections: has the correct network name information. When they attempt to access the network with the correct password, they show 4 bars of reception and a message of limited access (along with the above message). I did a little checking and found that our router info differs from their auto configuration.  Our IPv4 starts with 192 not  169 like thiers. Also, the subnet masks are different. Also, they have no info in the IPv4 default Gateway, IPv4 DNS Server, and IPv4 WINS Server.  Finally, my wife tried to acces the network with an ebook reader.  It shows secured WPA2, but won't access it.

View 2 Replies View Related

Linksys Wireless Router :: E3000 Internet Access Policy

Sep 23, 2011

Internet policy access on my Linksys E3000.  I am trying to block facebook.com to a particular ip address in my office.  This what I did.  Logged in to control panel clicked on access restriction.  Clicked on add.  Gave it a name.  Clicked the applies to drop down box and selected by ip address.  Unchecked the block all internet access.  Typed facebook down in the window below.  Saved.Not blocking access. 

View 9 Replies View Related

Linksys Wireless Router :: E3000 Behind ATT U-Verse / Cannot Access Internet

Feb 24, 2011

I can now access my router config pages when connected to my ATT router. However, I cannot seem to access the Internet when connected to my e3000; I just time out. I also have difficulties just connecting to my e300 for some reason. I have been connected a couple of times where i could access the Internet but it was only for a few minutes and it was very slow.I can't seem to put the router in the DMZ because the ATT router will only DMZ a DHCP-enabled device and the e3000 has a static IP (192.168.1.253). I have tried running the PING and Traceroute diagnostics and both just come back with Unknown Host no matter what URL i enter. The status page also appears as if the e3000 is not properly talking to the ATT router. Under the Internet Connection area it shows Connection Type: Automatic Configuration - DHCP then 0s for IP address, subnet, and gateway. the DNS entries are empty and the MTU shows 1500 and the DHCP Lease Time is also empty.  i am all ears and willing to try whatever. But i just want to be able to connect to my e3000 so i can utilize the wireless n internally and connect a 2TB external drive to share. But I also want to be able to get out to the Internet when i am connected to the device.

View 6 Replies View Related

Linksys Wireless Router :: Unable To Access E3000 Via Https

Feb 29, 2012

I can not access my Linksys E3000 router via https://192.168.1.1.Before this mishap, I was able to gain access to my Linksys E3000 router via http://192.168.1.1 and/or the Cisco Connect software application on Windows 7. Yesterday, I went into my router's administration page and disabled http, and enabled https. I then closed out all browsers, restarted them and entered https://192.168.1.1
 
After that, I learned quickly I made a huge mistake to make these changes. I simply can not access my router admin wired or wirelessly. Accessing the internet works great, but router admin page is a no go.Firefox and IE states, "There is a problem with this website's security certificate." and was unable to proceed.Firefox even gave me the option to accept a security exemption to proceed, but that failed.
 
I have also tried using the Cisco Connect utility, and that also failed. I have taken these steps and not been able to access my router's admin page.I don't want to take the last final resort to reset my router and re-enter my settings again. I know I saved the router's backup file somewhere, but can't find it.Is there another way for me to gain access via https with http disabled? All I want to do now is go back in and change it back to enable http access.

View 9 Replies View Related

Linksys Wireless Router :: Possible Remote Access To E3000 Unit

Jan 26, 2012

For a while now I've been thinking of setting up a (hopefully) secure remote access from a location outside of my local network. Since I'm going to be away from where I usually live for about six months due to the location of my Course that I'm going to study, I want to be able to remotely access the router if something were to happen. Up until this point, I've been doing the management through a Teamviewer 6/7 remote access with my home computer and connecting from the inside IP address (Example: 192.168.1.1), but it's going to be taken away so I wouldn't be able to do that this year. Is it possible to set up a secure telnet on a Linksys E3000 Wireless Unit that way I can control it through Command Prompt, or would I have to set up Remote Management Access to use the unit outside the network through programs like Internet Explorer or Mozilla Firefox?

View 1 Replies View Related

Linksys Wireless Router :: E3000 Become Insecure For Guest Access

Jul 30, 2011

Using Cisco Connest I set up a password for guest access. It will function for a time then suddenly become insecure. Sometimes it will function for a month, sometimes a week. I have to reset the Unit to factory defaults each time and began again.

View 3 Replies View Related

Linksys Wireless Router :: E3000 Lose Access To Internet

Mar 2, 2012

I have had numerous issues with my E3000 since I got about two months ago and they have all been resolved with the exception of this new one that popped up today.
 
My Samsung Blu-ray player is connected firectly via ethernet cable to the router.  When it's on, I lose all conenctivity to the router with my wireless devices including three PC's, a PS3, two iPhones, one iPad, one Samsung Smart TV, one XBOX 360 and an Onkyo Receiver.  When I say that I lose connectivity, I don't mean that I lose access to the Internet.  My PC's see the network but cannot connect to it, the same goes for the Apple devices.  The moment I shut off the Samsung BD player it kicks right back on and works normally.  Until today, this never occurred.
 
I contacted Tech Support and they had never heard of this happening before.  They suggested that I change the ethernet cable which I did while the unit was on and it worked until I turned the BD player off and turned it back on again.  I also tried switching ports to no avail.  Alos all of the software is up to date on both the router and the BD player.

View 3 Replies View Related

Linksys Wireless Router :: How To Enable Guest Access Feature Of E3000

Dec 30, 2012

I switched from comcast to att uverse.  I was happy about the guest-access feature of E3000 when using the comcast, where I can directly connect my e3000 to the modem (basically you can see two network, one is XXX, the other is XXX-guest). However, the ATT uverse has a gateway that combines the modem and router together, in order to use my e3000 instead of the built-in router of the gateway, I have done a LAN-to-LAN connection and I can access internet without any problem. But in this case, I can not enable my guest-access feature. When I use Cisco Connect to set up e3000, it says "cannot connect to your router". how to set up the guess-access feature of e3000 when using ATT uverse.

View 3 Replies View Related

Linksys Wireless Router :: E3000 Extremely Slow Menu Access?

Feb 29, 2012

I just purchased an E-3000 and when I log into the user interface it seems changing pages and saving settings takes forever. I click on a section in the router menu and it takes what seems like 30 seconds for the page to change or accept the new settings. It's not my browser it's definitely a Linksys Router issue. I updated to the latest firmware and latest Cisco Connect software as well. Is this slow user interface a normal thing with these routers?

View 1 Replies View Related

Linksys Wireless Router :: E3000 Cannot Access Admin Via Cisco Connect

Apr 25, 2012

I tried all methods: Cisco Connect (on Vista), http and https, but none works. However, the router seems function correctly. My laptop can acquire DHCP address and browse via the router. But I just cannot connect to the router to perform Admin tasks.Problem: when I launch CiscoConnect: the GUI shows "Cannot access your router", even though I am using the router to browse the net wirelessly and wirely. Using browser to navigate to http://192.168.1.1 and https://192.168.1.1 also give me cannot access error!

View 1 Replies View Related

Linksys Wireless Router :: E3000 - Guest Access To Internet Not Working?

Jul 8, 2011

We have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.

View 1 Replies View Related

Linksys Wireless Router :: Make WRT160N Access Point With E3000?

Jul 24, 2011

I want to use my WRT160n in my room to connect all my devices (Xbox, playstation 3, and 3 laptops) I hardwired the E3000 from the room downstairs thats connected to everything else.

View 2 Replies View Related

Linksys Wireless Router :: E3000 Possible To Limit Access For Specific Device (PC) To LAN Only

Dec 31, 2012

Within the Internet Access Policy section of the browser based utility, is it possible to limit access for a specific device (PC) to LAN only (not allow any traffic to external internet)?  I see that you can block internet access for a specific machine, however I didn't know if this was inclusive of LAN as well.If not, is there another way to achieve this via the E3000 or should I be looking for a solution on the specific PC itself? 

View 4 Replies View Related

Linksys Wireless Router :: E3000 Scheduled Access For Kids Devices

Jul 8, 2012

I am running an E3000 with Firmware - 1.0.04.
 
I would like to schedule my boys ipods to be on the network from 2:00pm to 4:00pm each day.
 
Running the Cisco connect software it would appear I can schedule from 2pm until the next morning but not a 2 hour window in the same afternoon.
 
Looking through other posts I see earlier software where this can maintained through the Router firmware but with 1.0.04 I seem to have to use Cisco Connect.
 
So how can this be done with my current configuration ?

View 3 Replies View Related

Linksys Wireless Router :: E3000 Guest Access And Static IP Addresses

Feb 9, 2013

I have an E3000 that I am just setting up.I have two issues:

1> I am replacing a WRT110. I had the old router set with a static IP address supplied by my ISP. I configured the E3000 with the same address and I cannot access the internet. Are there any tricks to setting this up on an E3000?

2> As configured I there is a guest network setup. BUT when I access the router I don't see the tab to be able to configure it.

View 4 Replies View Related

Linksys Wireless Router :: E3000 Running As Access Point Drops Devices

Nov 25, 2012

I am running the e3000 as an access point.. My iphone and ipad connect to it seamlessly. After a few hours to days, they are no longer recognized by the router. Nothing I reset on the phone or ipad makes any difference. The only solution I have found is to re-boot the router. They then re-connect on their own.

View 4 Replies View Related

Linksys Wireless Router :: E3000 - Guest Access Won't Prompt Password Dialogue

Apr 12, 2011

For weeks guest access to my e3000 worked fine. Today I have a friend come over, his XP connects to the guest wi-fi, but his computer does not get a prompt for a password.

View 6 Replies View Related

Cisco :: WPA2 Password Changed / Cannot Access Linksys E3000 Router Setup

May 21, 2011

I have a Linksys E3000, have had it successfully connected for three months now. Recently I attempted to connect my xbox 360 to the wifi and had issues connecting it. So I called ATT to obtain the PPPoE username and password, which they reluctantly gave me. Entered that into the xbox and still unable to connect, so I have given up on the xbox for the time being, I'll post that issue in a different forum. Where my issue is now is since contacting ATT the WPA2 password I set up for the router no longer works. I cannot access the router setup page, and I cannot add any new wifi devices. Although, all of the previously connected wifi devices are still connected to the router despite this issue. Is there anyway to make the old password work, or do I have to reset the router and start from scratch, and God forbid contact ATT again?

View 2 Replies View Related

Access Wireless Connection Through Cisco Linksys E3000?

May 15, 2011

I am attempting to access a wireless connection through a cisco Linksys E3000 installed on an HP desktop running Vista elsewhere in the house. I am on an HP Pavilion Laptop running Vista.We are connected to a cable modem.Under Network Adapters on the laptop, I have

Broadcom 802.11b/g WLAN
Microsoft ISATAP Adapter (this one has a yellow triangle with a ! in it)
NVIDIA nForce Networking Controller

I can access the internet most of the time on the laptop with a caveat:

There is always an ~10 minute delay before internet access is granted in addition to local access, before which time I cannot surf.In every case, when internet access is being granted, a Windows window comes up that wants to install a driver for a device.If I close the window using the x box, I can then surf to my heart's content.

If, however, I try to let Windows install the driver, I run into a loop where Internet Explorer can't open, followed by Windows trying to gather data about the problem, followed by IE can't open, ad infinitum, until i unplug the computer to stop the aforementioned infinite loop insanity.My default browser is Firefox.Is it necessary to let Windows install their driver, and if so, how can this be accomplished?

For El_Gourdo, have you just waited around for a while to see if the internet connection eventually comes? Maybe Windows (Vista/7) is "thinking about it" for a while. That is what it seems to be doing in my case.

View 1 Replies View Related

Linksys Wireless Router :: EA4500 And Traffic Monitoring / Logging?

Jan 7, 2013

I'm thinking of switching to another ISP which is faster and cheaper than who I'm currently with. Only problem is they have data caps. Any way to log inbound/outbound traffic usage with this router so that I can make sure I'm not going to hit monthly limits?

View 5 Replies View Related

Linksys Wireless Router :: E6500 Disconnecting Internet And Logging In Password

Oct 28, 2012

I am trying to configure my connectivity settings on my E6500. I enter 192.168.1.1 and the logon screen comes up. I have tried logging in with my user name and password and also disconnecting the internet and logging in the router password. After I log in, 98% of the time it says Router Not Found You are not connected to your router. It is funny that it is telling me this since this webpage is provided from the router since i have unplugged the internet. Even with the internet on, it does the same thing.
 
The times it does load the homepage of the router, I click on connectivity and when it does come up, the page is just blank with Ok, Cancel, and Apply buttons.I have done a reset on the router and reconfigured it with the CD and tried all the above again and same results.
 
I don't remember this being a problem when i first setup the router, it appears that a new firmware was automatically installed. I do not see any info on this being a known issue with the latest firmware.

View 6 Replies View Related

Linksys Wireless Router :: EA6500 Logging - Having Massive Network Variation

Dec 21, 2012

Is there a more detailed log or information from the router?I'm still having massive network variations, even with everything wire connected.

View 1 Replies View Related

Linksys Wireless Router :: Incoming / Outgoing Logging Broken On E2500 Firmware

Jun 20, 2012

Have a few of these routers internally as well as at various clients.  The incoming and outgoing logs show up blank, even when there are 10-20 computers using the Internet and I know there is traffic being generated.  DHCP and security logging still works fine.  I also have a few E1200s on the latest firmware that are logging just fine... I'm just having issues with the E2500s.

View 6 Replies View Related

Linksys Wireless Router :: E3000 FTP Not Seen On The WAN

Apr 22, 2012

I have a Linksys E3000 router set as Lan-Lan 192.168.0.2 hosting my internal LAN connected to a motorola Surfboard (Brighthouse) internet Wireless/Wired access point 192.168.0.1.I have a Web server hosting a site connected direct to the surfboard (works fine) . The FTP "site" on the E3000 can be seen by all pcs on the internal LAN. However, it can NOT be seen from the internet (Android with FTP client being used for test device)
  
Primary Access point 192.168.0.1
DCHP server with reserved IP addresses for server and PC's and smartphones
Port Forwarding Set for Server at 0.004 : 80
Port Forwarding Set for E3000 at 0.002 :21
 
Secondary (E3000) router 192.168.0.2
DCHP server is disabled
Port Forwarding is Not being used
connected to primary router LAN port 1 by LAN port 1 on E3000
 
All pc's can access the Internet when connected to the E3000 via cable or wireless?All pc's can access the FTP server on E3000 via cable or wireless as a LAN location (connected to either router)?How can I get the FTP to be seen from the internet ?

View 2 Replies View Related

Linksys Wireless Router :: How To Get Most Out Of E3000

Jun 29, 2011

I recently bought a Cisco e3000 router. I updated the firmware but I am still only getting 1.33 Mbps at most. The only things plugged into it is my PC and my xbox. I bought the router so i could get a better connection on my xbox so netflix wont stop playback.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved