I want to use my WRT160n in my room to connect all my devices (Xbox, playstation 3, and 3 laptops) I hardwired the E3000 from the room downstairs thats connected to everything else.
View 2 RepliesI have a FIOS setup with their Router/modem providing DHCP and Wireless routing. The problem I have is that I have a mix of older equipment and newer equipment. The newer equipment is capable of supporting WPA2, the older is not. I would like the benefits of WPA2, but still would like to at times be able to use the older equipment.My solution was to use a WRT160N v2 router that I had as an access point and it also gives me switch capabilities for wired systems as the FIOS router in on a different floor than the Linksys router. Wired access works just fine and the wireless worked fine until just recently.Since both routers have the same default IP addresses I changed the Linksys to a different static IP and turned off DHCP. I left all of the other defaults the same. I set up the Linksys for WEP and created the key for security. Everything worked fine for the better part of a year, but recently I am having problems where some of the computers cannot find the network or find it then lose connection.
View 9 Replies View RelatedI have a Router WRT160N and need to connect an Access Point using a wireless bridge (i.e. cannot use cable between router and AP). Which Linksys Access Point model is recommended to use with this router?(No I dont want to use another WRT160N with DD-WRT!)
View 1 Replies View RelatedI have a WRT 160n I want to use as an access point. The cable company has provided the main router so I want to use the 160 as the access point. I have a switch attached to the router and have the 160 attached to the switch. I can ping and access the 160, however there signal strength has not changed and is still extremely low. I know that the strength on the router is very good when I plug it in to the cable modem.
View 1 Replies View RelatedI just bought a Linksys E4200 wireless router. I have an old Linksys WRT160N wireless router. I would like to setup the WRT160N downstairs to wire the DirecTv box and PS3 to it. Then wirelessly connect to the E4200 upstairs where our modem is connected. Can the WRT160N be used as an access point to do this or do I need other equipment?
View 1 Replies View RelatedI got this router and I need to set it as an Access Point (will not be using the routing functionality) in the far side of our building. Our LAN uses IP address in the range 10 with subnet 255.0.0.0, so I need to put the access point ino this subnet. The drop down box only allows me to set some predefined subnet masks, none of which matches ours. So how am I supposed to set this router in our LAN?
View 9 Replies View RelatedI have a Cisco RV082 and I would like to connect my E3000 to it and use it as just a wireless access point. Is it possible to do this with the E3000 so the RV082 is providing the routing functionality?
View 1 Replies View RelatedI need to make my WRT54G an access point only. I tried information contained on Linksys site, but I can't seem to get it to work.
View 9 Replies View RelatedI have a desktop running XP. I am using comcast as my ISP. I have my printer attached to my Linksys wrt160N router via Ethernet. My desktop is also attached via ethernet. I also have a laptop attached to the router via wireless. How do I access the printer via the router from either the desktop or laptop? I had it configured properly in the past then lost my motherboard. Once the PC was rebuilt, I lost access.
View 6 Replies View RelatedI needed the Guest access of wi-fi setup that LinkSysys routers provided. I don't need the router/modem i just want to have wi-fi access point. I'm an advanced user and i can work with manual setup etc.I tried to do a manual setup of the router, i changed the IP address to mask my network and enable wi-fi and worked BUT the guest access option is NOT available unless you use the stupid CISCO connect software.
Now the cisco connect software IS NOT working or complete the setup if you don't connect it through the router and gain Internet access which is IMPOSSIBLE for me to accomplish as my modem is connected to a firewall device and we are using static DSL options with PPPoE and usernameme/password. There is no way i can get cisco connect to load properly as it always "fixes my connection trying to gain Internet access".Is there any solution on manually properly setup this router and take full advantages of it capabilities or should i return it ?
I am running the e3000 as an access point.. My iphone and ipad connect to it seamlessly. After a few hours to days, they are no longer recognized by the router. Nothing I reset on the phone or ipad makes any difference. The only solution I have found is to re-boot the router. They then re-connect on their own.
View 4 Replies View RelatedI have an AT&T broadband router. A WRT160N is connected to it, so I now have Wireless-N capability. I have a second WRT160N that I would like to put in my living room as an access point, so I can connect my BluRay player to it and stream video. How do I set up the second WRT160N as an access point?
View 9 Replies View RelatedI am using a windows vista laptop with a wrt160n linksys router. I want to make it an access point without using wires.
View 3 Replies View RelatedI have been using the E3000 for quite a while. A problem that I could not find a solution to is that the devices connected through Ethernet can't be viewed on Wireless, and vice versa. This is especially annoying because I want to get access to my media servers over wireless, for obvious reasons, but even those are not viewable (and using IP addresses on portables is a pain in the back)
View 4 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI want to extend the range for a Linksys router WRT160N. I don't have the possibility to use an access point with a wired connection. I read on this forum that can be used WAP4410N configured as repeater, without wired connection. Can someone who has used this solution to confirm that it works? What configuration should be done on the router WRT160N to permit wireless signal to be repeated by WAP4410N?
View 5 Replies View RelatedMy Linksys Wireless-N router/access point (WRT160NV2) is connected to the internet in my primary residence, delivering 35mbps. I purchased a commercial Engenius product (EAP9550) to amplify the wifi signal over to a secondary house (about 180 ft away, traveling through 3 walls). Configured as an access point, the EAP9550 received and showed signal, but there was zero connectivity. The tech support at Engenius has advised me to configure the EAP9550 as an access point. My linksys router continues to deliver wireless signal for its range, but is only showing (not giving) full connectivity to the secondary access point.
View 1 Replies View RelatedI am replacing an old G setup with the above system, Not interested in anything but an easy setup if I can avoid it.Set up the E3000 yesterday and was easy right out of the box. I'll receive the 2 AP's in a couple of days. The 2 AP's are hard wired to a switch along with the E3000. Would like to have the two AP's be JUST AP's! In other words, use the WPA2 of the E3000 only. Seamless roaming throughout the house, Is this possible?Anything I need to know before setting up the 2 AP's?
View 4 Replies View RelatedIs it possile make a bridge with my WAG54G2 and another Access Point ?
View 1 Replies View RelatedI have been using a Dell desktop for many years now as my primary computer. Recently I received a brand new Sony VAIO laptop. So as to make the laptop connect to the internet wirelessly, I hooked up a Linksys router (Linksys model # BEFSR41) and a Linksys access point (Linksys model # WAP200). Everything is working flawlessly except for one big problem. My network is listed as "unsecure". What steps do I have to take to make my network "secure"? The operating software in the laptop is Windows Vista. How to make my network secure. Let me just mention that the laptop and desktop are home computers and are both primarily used for "fun and leisure". No business "stuff"
View 9 Replies View Relatedi'm facing a big problem with my access point WAG54G ver 2.0 ,i just bought it from 2 days but i find alot of problems when i start using it ,i have read all the user guide and the quick install to see how to setup the access point and make it work with my adsl.i have configured all things right using PPPOE and putting my user name and password and then save settings then go to the status and press on connect , but it don't connect with me just i find connecting and adsl link : Down and still making connecting and nothing after that and my adsl led is off haven't any colors ,and when i get again to basic setup i found the password that i put it in the ppoe login is too long , not my password i tried to see what is this password and recover the hidden i found it " d6nw5vlx2pc7st9m ".i don't know what is the problem i tried alot of times to change setting and also the same problem.i think that it's a frim ware problem and i tried install a new updated frimware but everytime trying to install it get installing and suddenly stoped and white page appeard and all the access point is stopping and when restart it the ac power.
View 3 Replies View Relatedstep by step to make my router WRT54G as an access point?
View 1 Replies View RelatedI have a DCP 3925 with 2 telephone and 4 internet ports.So, how can I combine DPC 3925 + E3000 to have more internet ports? and wich one is the best wifi than I can use ??Main router is the DPC 3925, where the internet is connected.
View 9 Replies View RelatedI had an old G router that had an unsecured network. It died and I replaced it with an N router and installed a secured network. I have a cable modem with wires that goes to the router. From the router, I have CAT 4 wires going to several access points around the house. Into one of these acess points, I have pluged in a wireless access point that broadcasts wirelessly---unfortunately, it is broadcasting the old unsecured network. How can I make the wireless access point broadcast the new secured N network?
View 6 Replies View RelatedI brought a LAP1131AG, only later found out that it can only be used with a controller.Is there any way I could change the firmware to make it a normall Access Point?
View 5 Replies View RelatedI recently purchased the E3000.I thought i had read that this devices can act as an access point. There is no clear "access point" mode option so i configured it as best as i could to work with our radius server. I can connect to the wireless with radius credentials just fine but i don't get assigned a ip address from dhcp. I tried using an old blekin that does have ap mode and it works just fine.
View 1 Replies View RelatedEven when I disable remote access, people still can get to my router login by typing my external IP. Is there anything I can do to stop this?
View 5 Replies View RelatedWhile trying to add my kindle fire (unsuccessfully) I lost all internet connections, now my laptop won't connect. I reset the router and and can see my wi-fi account but when I try to use on my PC and laptop it won't recognize it.
View 3 Replies View RelatedI have Linksys router model no. WRT160N, which I have been using for three years. I need to add two iPads to my router but I do not know the network password. I am trying to access the router IP address 192.168.0.1 to find out the network password, but when I put HTTP://192.168.0.1 in my browser, I receive the message: Internet Explorer cannot display the webpage. How can I find out the network password?
View 9 Replies View RelatedI am having trouble logging in on my wireless router and when i put "admin" (WITHOUT QUOTATIONS) on the password, the same prompt kept on coming for three times and after that the message says "401 Authorization Required" (WITHOUT QUOTATIONS). I don't get though, i installed the wireless router just after i change admin and my password into (******).
View 9 Replies View RelatedI have a wrt160n v1 that stopped working after a power outage. The power light stays solid and I cannot reset the device with the reset button, power cycle, and I cannot access the user interface at 192.168.1.1. Is it bricked? It doesn't show up on my wireless network and when I try to access it via ethernet cable it shows up as an unidentified network with no network access
View 2 Replies View RelatedI have updated the WRT160n firmware and, since then, I couldn't access the setup page anymore. I could still use the router as a switch, but couldn't access the setup page and configure it as a router.
View 5 Replies View RelatedEverything was going great until tonight. I can connect to the internet fine wired. Wireless devices can connect to the router, but cannot access the internet. No changes were made to the unit. Updatae firmware to 1.02.11 but that did not fix the issue.
View 1 Replies View Related