Linksys Wireless Router :: E2500 5ghz Ssid Not Visible?
Dec 25, 2012
None of my wireless devices (Windows, iphones) can see the SSID from the 5ghz channel on my E2500. I have updated the firmware and reset the router to factory defaults. Still not visible. The router is set up to broadcast the SSID under wireless settings. Also, selecting "other" under iphone>settings>wifi and entering the SSID name and password gets "could not find the network (ssid)". This was working until a couple of days ago Comcast power cycled the router to make sure my cable modem was working. Now nothing.
View 2 Replies
ADVERTISEMENT
Jul 1, 2012
I've recently purchased the E2500, done the setup but am facing some issues.I'm unable to see the 5GHz channel SSID, I can only see the 2.4GHz channel SSID.Have tested all the laptops and devices at home and all can't see the 5GHz channel.The list of devices are:
a) iPhone 3GS
b) iPhone 4G
c) iPhone 4GS (some sites says it doesn't support, some says it does, I'm confused as a result)
d) Samsung laptop
e) Dell laptop
f) Momo11 Little Bird Edition tablet (Made in China [MIC])
g) No name MIC tablet
Secondly, is there any tips / tricks to tweak the modem to increase the internet speed?
View 1 Replies
View Related
Feb 20, 2012
I am using the E2500 with the Wireless N-pci adapter with dual band, both with the latest drivers / firmware, and I am getting extremely low signal quality and connection speed when connecting to the 5 Ghz network.My computer is no more than 15 feet away from the router, and on the same level. I also verified the connection with the 2.4 Ghz band, and it reads as excellent, and with 54 mps. Using 5 Ghz I get one bar of signal quality (very poor) and no more than 13 mps connection speed.
View 9 Replies
View Related
Jun 27, 2012
I've found a few people with this problem on the internet. I'm using my phat 360 with the black N adapter. e2500 is updated to the latest firmware. But my 360 cannot connect to the 5ghz N, only 2.4ghz g. The wierd thing is that the 5ghz signal gives a better signal than the 2.4ghz.
I just found a thread on google talking about the e4200 and someone mentioned counterfit adapters and problems with them. I did buy this on ebay for a cheap price, so it looks like it was too good to be true. this is a counterfit? It does have a real hologram on it.
[URL]
If this is real, what else could be the problem. Has the firmware not been updated to support the 360?
View 6 Replies
View Related
Sep 10, 2012
I have found that if I do not enable the broadcast SSID option on my 5GHz N network that my devices will forget the network and not reconnect on their own. Yet, I have the 2.4GHz G/N network set up to not broadcast my SSID and I have no problems. Why can't I disable my SSID broadcast on the 5GHz N network without these problems?
View 9 Replies
View Related
Feb 23, 2013
On my dual band E2500, I have both the 2.4 and 5 GHZ enabled. I have a fairly new HP with an N wireless card but I cannot get it to connect at the 5GHZ frequency. The only computer that will connect at the speed is my wife's with an external Cisco wireless card. What the settings should be on the PC in order to get it to connect at the higher frequency?
View 4 Replies
View Related
Jul 1, 2011
I was quite excited about E4200 I got yesterday. Everything works perfect except front LED light start blinking a few hours later. Don't know why it happens in a sudden and non-stop. After several tries, I found that disabling SSID broadcast for both 2.4 and 5GHz stops the blinking.Of course, before doing that, I upgraded firmware to 1.0.02, reset to factory defaults and finally set up E4200 manually rather than using Cisco Connect. Now the LED light is continuously lit.
View 4 Replies
View Related
Aug 15, 2012
I just bought a Linksys E2500, and I'm trying to configure multiple SSID's on it. The "guest mode" won't work for me because I want one SSID to use WPA and the other to use WEP, but the option to set different encryption based on the GHz frequency of the connection won't work for me because I only want the WEP one to be used by my Nintendo DS (which doesn't support WPA); I don't want to force ALL devices that don't support 5GHz to use the WEP one!
View 9 Replies
View Related
Jan 25, 2012
I have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet
View 1 Replies
View Related
Dec 1, 2011
why my SSID still displays even though I have the SSID Broadcast "Disabled" for 5 GHz and 2.4Ghz configurations. The name of my network shows full signal strength and a lock next to the name but I was under the impression if I have disabled the SSID broadcast it shouldn't show up at all and would force a user to manually input the network name when trying to connect to it. I have the router configured to only allow certain MAC addresses wireless access as well. Router is running Firmware Version: 1.0.03.Also, my primary computer my iMac running 10.7.2 boots up or is brought out of sleep mode I constantly need to go up to the top of my screen and re-select my network.
View 4 Replies
View Related
Dec 2, 2012
I just got a new E2500 and out of the box the system uses the same SSID for 2.4 GHz and 5 GHz. Obviously you CAN configure them to use different SSID's, though. Should I make them different or keep them the same? I don't really want to mess around with having 2 different SSID's if I don't get a real benefit.Will most devices that support both (like a new laptop) find and use the 5 automatically?
View 7 Replies
View Related
May 26, 2012
Is it possible to change one's private network name as well as SSID?
View 1 Replies
View Related
Jan 27, 2012
Just got an E2500 and installed it with no problems and it was working correctly for 1-2 days. This evening the signal strength of my SSID dropped to LOW and a new SSID now shows up with full signal strength. It s not an SSID from any of my neighbors and from checking several forums it appears this is known problem.
View 2 Replies
View Related
Mar 5, 2012
I've had the DIR-825 router for more than a year now and I've never once been able to see the second SSID that broadcasts at 5Ghz. I've set up both bands with identical settings and I have a wireless N network adapter in my laptop, but it only ever sees the 2 Ghz SSID, never the 5 Ghz one. Shouldn't I be able to see it?
View 3 Replies
View Related
Jan 8, 2013
In my new laptop with os windows 8 my 5Hz network is not visable.My 2.4Ghz network is the only one that is showing.
My Router is a Belkin N600DB
Hardware F9K1102 v1
Firmwareversie 1.00.19 (Jul 6 2012)
Versie opstartprocedure v0.07
View 1 Replies
View Related
Apr 9, 2013
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
We are trying to use a TL-WR941ND purchased about a month ago, but it keeps hanging, usually within a day or so of operation.To be clear: by "hanging" I mean the device stops providing wireless services (its SSID is no longer visible in WiFi clients) and becomes nonresponsive to pings or control access attempts (via settings web page) from the internal network connections.The device is used in a very simple scenario, where it's being employed as a simple access point, not as a router. As such, the device's configuration is as follows:
* WAN interface is configured with a dummy static IP (10.10.10.10/24) with gateway and DNS set to the internal IP address of the actual routing device connected to the external world.
* LAN interface is configured with an IP address inside the actual internal IP subnet (192.168.1.0/24).
* DHCP is also disabled as this service is already provided.
* Wireless settings: radio enabled, SSID broadcast enabled, WDS disabled, 11bgn mixed mode, auto channel width, max TX rate, channel 7 (manually set). Using WPA-PSK security.
Rest of the settings are unchanged from their default values, as the device isn't being used as an IP router by any client - just as a WiFi/Ethernet layer 2 bridge. We're using what appears to be TP-Link's latest stock firmware for the device.The settings described above appear to provide the connectivity required by the WiFi clients. However, the device continuously hangs within a day or so of operation, requiring someone to physically attend to the device and cold-restarting it (disconnecting it from power and reconnecting it) to regain an operational state.
After performing a cold restart, the system log shows nothing beyond the startup entries: "System started" entry followed by security info entries regarding enabled protocols. Then the device appears to work well for a while, until it hangs again, forcing again someone to attend to the device, etc.
View 6 Replies
View Related
May 6, 2013
I'd like to set up a 2.4Ghz and a 5Ghz SSID at the same time, using one Cisco AP541N-E-K9. But I can't figure out any way to do so.
View 1 Replies
View Related
Mar 26, 2013
I have TV set box connected to modem router supplied by ISP provider. To the same router I connected EA 4500 to which I wired connected Network Hard Disc at which I store music, photos and films, which I can not access via TV set box. If I connect Hard Disc direct to the modem router to which set box is connected, access works fine.
Whar shall I do to establish accesability of Network Hard Disc over all network ?
View 1 Replies
View Related
Dec 29, 2012
F9K117 - I can't see my broadcast ssid for the 5ghz band. Is there anything I can do?
View 3 Replies
View Related
Aug 10, 2011
I'm using a linksys WRT54GS 7.2 router and I can't get any of the ports to be visible. I've set a static ip, and setup everything according to portforward.com and previous experience, I've never had to get ports to work with either this router or computer, so I can't say if it's ever worked for either. According to [URL] the connection is timing out before connecting.
View 2 Replies
View Related
Aug 21, 2011
I have e4200 router set up with different SSIDs for 2.4ghz and 5ghz. My laptop (Lenovo x220 with Intel 6205 wireless adapter) can't see the 5ghz network. I've tried changing the channel for the 5ghz network and it didn't fix the problem.
View 9 Replies
View Related
Nov 23, 2011
Wednesday, November 23, 2011I have an Airport Extreme dual-band 2.4Ghz and 5Ghz. Each network is has a different name and different password so I know exactly which one I am connected to.On a MacBook Pro, it sees both networks. On a Dell E5520 it will see both networks. On an iPhone 4 it will see both networks. I can connect any of these devices to either network.Just got the Linksys E3000 dual-band 2.4Ghz and 5Ghz. Each network is has a different name and different password so I know exactly which one I am connected to.On a MacBook Pro, it sees both networks. On a Dell it will only see the 2.4Ghz network. On an iPhone 4 it will only see the 2.4Ghz network.The Airport Extreme is powered off when using the E3000 so I know there is no interference from this router.E3000 Firmware Version 1.0.04. It's the latest.5Ghz Wireless Settings
Network Mode: Mixed
Channel Width: Auto (20Mhz or 40Mhz)
Channel: Auto (DFS)
2.4Ghz Wireless Settings
Network Mode: Mixed
Channel Width: Auto (20Mhz or 40Mhz)
Channel: Auto (DFS)Did not mess with any other settings. I have rebooted the computer, cycled the router and modem 3-4 times.Nothing works.My question is since both laptops and phone can see the 5Ghz network when running the Airport Extreme, why doesn't the 5Ghz network show up on the Dell and iPhone when running the E3000.
View 5 Replies
View Related
Apr 23, 2012
My channel width is Channel Width is 40 mhz only, and my channel is Auto DFS?These seem like good settings?My macbook air sometimes see's my 5ghz wireless SID, and sometimes it connects to it, but i still have no internet access for some reason
View 3 Replies
View Related
Mar 15, 2013
EA2700v1 WPS-PIN using 5GHz does not work. This router includes WPS header in its 5GHz beacon and probe response but the router removes the WPS header from them once WPS-PIN starts. There is no problem with WPS-PIN using 2.4GHz.
View 1 Replies
View Related
Dec 25, 2012
EA6500 5GHz band only four channels (36,40,44,48), the lack of 149,153,157,161 channel, firmware Ver.1.1.28.146072, how to add 149,153,157,161 channels?
View 3 Replies
View Related
Feb 21, 2012
I ended up with an RMA for a new E4200 ver. 1 and the problem I have still persists. My 2 GHZ WAP gets 65Mbp/s to its connected devices. However, the 5.4 GHZ WAP gets 48 to 54 Mbp/s only.My laptops have Windows 7 and Ubuntu. The WiFi cards are Intel Centrino Advanced-N 6200 and 6230. Both fluctuate at 48 - 54Mb/s on the the 5.4GHZ channel.
If I put it on Wireless-N only, the laptops cannot connect. I have tried AUTO detection for mhz and channels. I have tried 40mhz with channels 149 and 161 with no difference.Currently, I am operating both WAPs on different SSIDs to make sure my results are separate.Security for both WAPs is WPA2-Personal with a 10 digit sequence.
View 9 Replies
View Related
Dec 30, 2011
I had a e4200,and i used 5ghz wireless.i can't set it to channel 149 or other high channel,my old wireless ethernet card can only support that.make the next version of the firmware can setting 5ghz channel to channel 149、153、157、161.
View 2 Replies
View Related
Feb 2, 2012
I purchased the linksys 3200 dual band router recently. I am a huge cisco and linksys supporter so for me this is disappointing. Aside from being slower at times than my previous router I am having issues with the 5Ghz wireless. My issue I am facing is it seems multiple times throughout the day the router somehow drops its 5ghz wireless ssid or its gone..not sure. The only way I can get it back up and running is to reconnect with the Cisco Connect software and re-establish the settings and then reconnect any wireless devices. This seems to happen sporadically and is insanely annoying considering this router should be a big upgrade.
It seems to me the 2.4Ghz band seems to be more stable. I am on the latest firmware for the device and I am using a 5ghz compatible wireless device to connect to it.
View 9 Replies
View Related
Oct 23, 2011
Router: E4200
Router Firmware: 1.0.03 (Latest FW)
Why I cannot go to the 5Ghz band to utilize the superior speeds to transfer files over wireless connection between my computers? I am sure that I am still on the default 2.4 Ghz because
1) The file transfer speeds are pathetic
2) In Wireless Security, if I set the Wireless Mode to disabled for the 2.4Ghz band, Windows shows me "Unsecured Network" even with 2.4Ghz disabled.
View 9 Replies
View Related
May 3, 2012
I have the E4200. I have two networks, a 2.4 for internet, and a 5gHz for media. I want to have a wired connection to the 5gHz network as some of the media is on my PC. However, it seems I can only have a wired connection to the 2.4gHz network. Is there any way to do this?
View 3 Replies
View Related
Jan 20, 2012
I have an E4200v2 configured with an n-only 5GHz network and a mixed 2.4GHz network. Our MacBooks and iPad connect to the 5GHz network, and everything else (iPhones, TVs, etc) connect to the 2.4GHz network. If I disable "WMM" on the QoS screen, nothing can connect to the 5GHz network. Those same devices can connect to the 2.4GHz network, but not the 5GHz. The MacBooks, for example, get a connection timeout error, and the iPad just says "cannot connect." This doesn't seem quite right. I don't absolutely need to disable WMM, but I wanted to make sure that normal WiFi Internet traffic didn't get priority over local wired Mac->AppleTV streaming or voice calls from our wired Vonage box.
View 2 Replies
View Related
Apr 15, 2012
I'm using a Linksys E3200 router with a Motorola modem and an elite xbox 360 with a wireless N networking adapter. (Black with two antennas.) I just recently bought this router because I wanted some faster gaming. I wanted to put my xbox on the 5ghz so it would have it all to itself, and have the two laptops share the 2.4ghz. But it won't let me onto the 5ghz band... I can see it on my xbox but it won't connect to it at all. I can get onto the 2.4 band but its at 802.11G, so its not even giving me N there, when it should be. I'm not sure if this is an issue with my adapter or router...I tried finding stuff about it, and it looked like people were blaming it on linksys, but that was almost a year ago. And there was never an update on what happened.I can see the 5Ghz band on my xbox (but only if the channel width is on 20Mhz only), but I can't find it on my computer. Which I find weird. I've been trying a lot of things and I just can't get my laptop to find it. So nothing is using the 5 band, and all my devices are crowded onto the 2.4...Is there some step in setting up the 5Ghz band that I'm missing maybe?
View 4 Replies
View Related
Jun 23, 2011
I bought an e4200 about 2 months ago. It worked perfectly for 3 weeks. Then all of the sudden, the 5ghz connection started dropping. Then it's disappeared completely and it would not show up in a network search. Then the 2.4 ghz started going crazy. I reset it completely, that didn't work. I let it sit for half a day, nothing. I sent it back to newegg and got a replacement. When the 2nd one came in, it worked fine until the next day. 5ghz cut out. I called linksys support and they were no luck. I reflashed to 1001 firmware and it mysteriously came back to normal. It was working perfect until today. 3 weeks later. 5ghz went out, and never came back. I reflashed 1001, nothing. Reset, nothing. Flashed the new 1002 firmware, nothing. 2.4ghz still kind of works, but the speed is barely 5mbps. I'm at a freaking loss right now. This was the best performing router I have tried, of all the top models available right now
View 8 Replies
View Related
