On my dual band E2500, I have both the 2.4 and 5 GHZ enabled. I have a fairly new HP with an N wireless card but I cannot get it to connect at the 5GHZ frequency. The only computer that will connect at the speed is my wife's with an external Cisco wireless card. What the settings should be on the PC in order to get it to connect at the higher frequency?
View 4 RepliesI just recently (4 days ago) purchased an E3200 router. I noticed some random disconnects on my devices using the 2.4GHz frequency.I installed inSSIDer from MetaGeek to see what was going on and noticed some strange behavior where the Amplitude on the 2.4GHz randomly drops dramatically. Sometimes its once every 10 minutes, other times it happens 5 times in one minute. I can't figure out what is the cause. The 5GHz signal is steady as a rock.
What I tried so far: Set the Channel to the least crowded channel instead of auto, upgraded the firmware, restarted the router all to no avail. This is annoying to say the least. It doesn't affect anything unless you are playing video games or running a remote desktop session, where a single disconnect is disastrous. I just upgraded from an old linksys wrt54g, tried a netgear n600 which was terrible, then swapped it out for the Cisco E3200..
How do I know if I'm using 2.4 or 5ghz? I would like the laptop and ps3/net flix to use the 5ghz and everything else to use 2.4ghz. I used the e3000 CD fro the setup. When I was at the last part of the setup, when it gives you a ssid name and password. I deleted it and typed in a name that I could remember. I clicked the button for the next step and everything was complete. I also received another name for guest to use the computer. The e3000 setup just game me some wild name like running water.
I would like to know since I have two different names, which on e is using 5ghz and which one is using 2.4thz? Can you tell me if the e3000 automatically have the first name use 5ghz and the guest just 2.4ghz on the second name?
2 days ago my e1000 died, so I went big and bought the e4200 (due to newness, its already loaded with Firmware 1.0.03 build 14) to aleviate my networking woes. I'm running into an issue where I'm utilizing both the 2.4Ghz bands and the 5Ghz band. My desktop as an AE1000, and I'm utilizing that on the 5Ghz band. Everything else in the house (Dell laptop, 2x iPhone 4 and an HP printer) are all connecting to the network wirelessly.
I have had 0 network issues with regards to my wired connections, or my 5Ghz connection. But my 2.4Ghz connection will continuously be unavailable. I have both bands set to brodcast, they have different names so my AE1000 can connect via 5Ghz band. Both yesterday evening, and this morning, my phones, laptop and printer cannot connect, and for the most part, the network doesn't show up on available networks. When it does show up, the devices can't connect.I'm proficient enough to do the general home networking, but I'm at a loss as to how to fix this, without a daily reboot of the router (which seems excessive and unwarranted for a 2 day old e4200 [or any router to be honest]).
I am using the E2500 with the Wireless N-pci adapter with dual band, both with the latest drivers / firmware, and I am getting extremely low signal quality and connection speed when connecting to the 5 Ghz network.My computer is no more than 15 feet away from the router, and on the same level. I also verified the connection with the 2.4 Ghz band, and it reads as excellent, and with 54 mps. Using 5 Ghz I get one bar of signal quality (very poor) and no more than 13 mps connection speed.
View 9 Replies View RelatedI've found a few people with this problem on the internet. I'm using my phat 360 with the black N adapter. e2500 is updated to the latest firmware. But my 360 cannot connect to the 5ghz N, only 2.4ghz g. The wierd thing is that the 5ghz signal gives a better signal than the 2.4ghz.
I just found a thread on google talking about the e4200 and someone mentioned counterfit adapters and problems with them. I did buy this on ebay for a cheap price, so it looks like it was too good to be true. this is a counterfit? It does have a real hologram on it.
[URL]
If this is real, what else could be the problem. Has the firmware not been updated to support the 360?
None of my wireless devices (Windows, iphones) can see the SSID from the 5ghz channel on my E2500. I have updated the firmware and reset the router to factory defaults. Still not visible. The router is set up to broadcast the SSID under wireless settings. Also, selecting "other" under iphone>settings>wifi and entering the SSID name and password gets "could not find the network (ssid)". This was working until a couple of days ago Comcast power cycled the router to make sure my cable modem was working. Now nothing.
View 2 Replies View RelatedI've recently purchased the E2500, done the setup but am facing some issues.I'm unable to see the 5GHz channel SSID, I can only see the 2.4GHz channel SSID.Have tested all the laptops and devices at home and all can't see the 5GHz channel.The list of devices are:
a) iPhone 3GS
b) iPhone 4G
c) iPhone 4GS (some sites says it doesn't support, some says it does, I'm confused as a result)
d) Samsung laptop
e) Dell laptop
f) Momo11 Little Bird Edition tablet (Made in China [MIC])
g) No name MIC tablet
Secondly, is there any tips / tricks to tweak the modem to increase the internet speed?
Can i run both 2.4 and 5ghz at the same time? so my N user's can connect at 300Mpbs on the 5ghz bonded, and my G users can connect to 54Mbps?Also i ask because of coverage, my 5ghz does not cover as far as the 2.4 so those at the extremity's could at least get G with a good signal?
View 4 Replies View Related1142N-E0K9 will support both 2.4 and 5 ghz or only 2.4 .
View 4 Replies View RelatedWe ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas instead of the 2.4GHz antennas.Would it be possible to use the 5GHz antennas as 2.4GHz antennas?If so, are there any down sides to it?
View 15 Replies View RelatedI'd like to set up a 2.4Ghz and a 5Ghz SSID at the same time, using one Cisco AP541N-E-K9. But I can't figure out any way to do so.
View 1 Replies View RelatedWRT610v2 running latest firmware.xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars.Connects to 2.4 network just fineWon't pull an ip address and reports "Not connected" when I select the 5.0 network.I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network.So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not..If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
View 13 Replies View RelatedIs it possible to establish the WDS-connection on 5GHz and connect Wireless-Clients on 2,4GHz with these Acces-Points?There are some threads concerning performance-issues in combination with WDS on 541 - any news on this with the actual software-release?
View 1 Replies View RelatedThis first started when a user said they were getting disconnected and reconnected a few times a day to our wireless network. He is in a remote office with a 1142 which is set to H-Reap talking back to our 5508. Our WLC is running 7.0.166 The laptop has an intel ulitmate 6300agn wireless card with the latest 15.x drivers.
We are using an SSID with wpa2 and 802.1x auth back to our ACS server using PEAP with our windows credentials.attached is what i am seeing on the wcs troubleshooting page.When i do a debug client on the WLC i see many reauthentications coming from the client on the different radio.
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Reassociation received from mobile on AP 0c:85:25:f3:7d:40
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c 10.24.8.108 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying site-specific IPv6 override for station 00:24:d7:d1:16:6c - vapId 512, site 'VH-GasWorks', interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying IPv6 Interface Policy for station 00:24:d7:d1:16:6c - vlan 2, interface id 0, interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying site-specific override for station 00:24:d7:d1:16:6c - vapId 512, site 'VH-GasWorks', interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c 10.24.8.108 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c STA - rates (8): 140 18 24 36 48 72 96 108 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Processing RSN IE type 48, length 38 for mobile 00:24:d7:d1:16:6c
[code]....
Now this may be not be the issue thats causing our dropouts a couple times a day as this is happening every 5 mins.
Is it possible to connect my WAP54G to my new E2500 router?I previously had a WRT54G and had my WAP54G connected to it in AP Client mode. This enabled me to have internet access on my desktop computer that is located in another room downstairs.I would like to configure my WAP54G to work with my new E2500 router in the same way.
View 2 Replies View RelatedI recently installed a refurbished E2500 router. The reported speeds I got when hovering over the icon in the system tray ranged from 54 Mbps down to 1.0 Mbps. Also, it would drop, then reestablish, the connection several times per day.I contacted Tech Support via Live Chat, and got a woman who told me it was due to the fact that I'm using the router with an older system that has a wireless-G card (I'll be getting a new system soon).Of course, I thought that was ridiculous, so I called Linksys Tech Support and got a young man who had me reinstall the firmware upgrade (which I had already done when I installed the router). After that, it was good for about 24 hours, then the problems manifested again.I returned the router and ordered a replacement, also refrubished. Again, I upgraded the firmware upon installation. .
View 4 Replies View RelatedHave set up Router OK. Created Flashdrive EZ
How do I connect my IPAD now to WiFi since there is no USB port on my Ipad??
I recenlty bought an E2500 router. I was able to connect 4 of our laptops at home just fine. But when I tried to connect my Acer One netbook, the "Cisco Connect" loaded up to 25% & then I couldn't connect to the internet. I've contacted Tech Support & they suggested downloading the latest wireless adapter driver. I contacted Acer & they said it sounded like a security issue on my netbook. I was out of warranty so they'd have to charge $150 for tech support.
View 2 Replies View Relatedjust replaced my WRT54GL with e2500 and i have a problem connecting my bridge (WET610N) to e2500 router, it connects fine, but no internet when i connect the bridge to another PC (bidrge says it's connected and got IP), same story with another router (WRT54GL) i connect it with the wire to the e2500 than connect to that router with wi fi and OOPS no internet when i connect to e2500 directly with laptop, iphone etc i have the internet connection, but when i connect the bridge or another router i get no internet looks like E2500 does not let the internet pass throught the bridge or other router.
View 3 Replies View RelatedJust replaced a long-serving WRT54GS with an E2500 to gain a single feature… DHCP reservations for a bunch of web cams around my home. So far, the owner/user-experience with the 2500 has not been as positive as it was for the 54 or any of it's predecessors here and at my business. They just worked when you set them up, and once set up, they stayed set up. Zero futzing around with details. Some issues I'm seeking more expert input on:
My Panasonic Viera DVD/blueray player can access the web. Worked fine on the 54… access "Network" and 50% of the time it would join the network then and the other 50% of the time, you had to try a second time which I presume was the time it took for the device to gain access to the network. With the 2500, you can't ever (so far) get on by selecting "Network"… you have to go into the sub menu and have it dwell in the Network menu where it appears to make an ongoing effort to get onto the network. About 30% of the time, you get on… the other 70% no joy.My HP wireless printer will join the network if you dive into its menu system and tell it to look for the network. However, sitting at any of the computers on the network, you can't "get the printer's attention"… it just doesn't join and the print fails. You go over and use the printer's menu manually to get it on and it stays on for a short time, but it soon quits and that's the ball game.My Google Nexus One phone is a slightly different experience… it goes off the network as soon as you shut the screen down but, it seems like it comes back when you turn it on. With the 54, it seemingly remained in touch with the network better… things came in over the net while it was in my pocket. So, works better than the other two but I don't see why it goes away when on the 54 router, it didn't seem to.
In case it matters, this system is set up with DHCP, WPA2/personal and MAC filtering as was the case on the router(s) it is replacing. UPnP has been disabled. On 1.0.03 of the firmware. There are 6 DHCP reservations which also receive port forwards. I have adjusted the Beacon Interval, Frag threshold and RTS threshold for both frequencies and the MTU, all in accordance with recommendations under the support area for this site. Since everything worked well for both the 54 and its predecessor, I have to believe it's the 2500 that's the problem.
I just bought an E2500 router, and am only getting a fraction of the speed I do by connecting without it. Both wireless and wired through the router I'm getting about 1 mbps, while without it I'm getting about 10 mbps.
I do live in an apartment, so I'd understand if there were some wireless interference going on, but would that explain away the wired issues too? I've also tried changing the channel (though only of the 2.4 GHz connection), and that's not working any.
I have a Linksys E2500 and I'm trying to connect it to my ISP provided router (Actiontec V1000H) because I wanted better range and consistent connectivity for my 6+ wireless devices.My problem is that, to make this work, I connected an Ethernet cable from the E2500's yellow internet port to one of my V1000H's LAN ports. This, however, did not give me access to the internet even though the network for my E2500 was available in the network list and selected as the default network. I then had to go the the advanced settings of the E2500, and changed the router IP address from 192.168.1.1 to 192.168.2.2. This granted me internet access.However, everyone i've talked to including coworkers and experts at dslreports said that, because of what I've done I've set up a double NAT with 2 potentially conflicting IP addresses, and down the road weird issues will arise because of it. They also suggested I connect the E2500 to a dedicated modem to avoid this problem. However, the dedicated modem I was sent was faulty and did not allow internet access even through the ethernet connection. So, until I get a new dedicated modem, I have to use the router/modem combo.What should I do? Should I set up the E2500 as just a wireless access point for my existing router/modem combo? What do I need to edit in the advanced settings?
View 6 Replies View RelatedWhere I work, we have four computers connected on a network with a Telus combination router and modem (I should probably also mention that two of the computers are connected to a switch which is then connected to the Telus modem/router because that is how the previous tenants set it up) . Recently, my boss wanted to have two different wi-fis, one as a guest wireless and a password one for the employees so he bought a Cisco E2500. I set up the second router as a wireless access point, but eventually we started getting problems with IP conflicts which started messing with the work group connections.
How I'd go about setting up the E2500 properly so that there are no problems like I've been having (having to reset the modem/router constantly for the internet to work, computers being assigned different IP addresses and problems connecting to the server over the workgroup network).
I want to install wireless router in my home. It is 200 Square metres. Usb port does not meter for me. I want to connect 2 laptop 3 mobile phone via wlan. Which will be better E2500 or E3200 to cover whole area? P.S my internet speed is 40mbps
View 1 Replies View RelatedI would like to know on what frequency band running Linksys EA4500 for 5 GHz because in Israel only allowed frequencies from 5150 to 5350 MHz.
View 1 Replies View RelatedAnyone has a register of problems between a router WRT54GH and A495 telefone of Siemens?I mean they can be working in the same frequency, that´s why in some rooms I can connect my wireless network very well.
View 1 Replies View RelatedWhen it comes to networking and require some advice on setting up my wrt61on router with my airport express. I have managed to get it all connected up and working but am suffering frequent dropouts while streaming music. I have done a little reading and have tried changing a few settings on the router but have found no improvement. My set up is as follows.
-Modem connected to WRT610N Router
-Desktop Computer connected to network via wusb600N dongle
-Airport Express connected via wif
-Using Iphone 4 as remote
Is there a way where i can set up the airport express on a total different frequency to everything else in the house i.e laptops iphones etc to prevent these cutouts.
I have 2 laptops (Inspiron 1525 and 1545) and was wondering if I can connect to my Dual Band 5GHZ router with this? I don't see the SSID in my wireless area on my computer.
Are my laptops compatible with a 5GHZ connection? If not, is there an adapter for it, how much is it, and it is easy to do?
I purchased a EA4500 and at first I could connect to it through its default ciscoxxxxx ssid on my laptop which is 2.4GHz only. I upgraded the firmware using the PC utility and now I can't find the 2.4GHz SSID no matter what settings I do. I've disabled and enabled it multiple times, changed it to have no security or with security and enabled and disabled it and renabled it. Nothing seems to work, but for some reason the 5GHz side I can connect to using a 5GHz device. I've also tried disabling the 5GHz side, but still no 2.4GHz.
View 4 Replies View RelatedDecided to go with the e4200v2. 199.99 for a router 450 + 450 with a little extra features. very pricey but thought it would be worth it. I got it hooked up with no problems for the first 5 minutes. I have 35mbps down wired from the router and on the 2.4 and 5.0 ghz band about 25 feet from the router was getting just that!! no loss really. However after a few more speed test i noticed it was fluctuating very slow to fast. Also the 2.4ghz was only 144mbps. after getting in the router i changed the 2.4ghz to channel 6 and 5ghz to 153 and changed to 20mhz only on the 2.4 and 40mhz only on the 5.0ghz. Now all is doing well .
1. why am i not able to run the 2.4ghz on 40mhz? when set to auto i have a lot slower speed tests even know it is running on 20mhz only because I'm only getting 144mbps. I don't know why its not running 40mhz ? i don't know why i have to change it to 20mhz only why cant i leave it on auto and if i had a day with little interference it would switch to 40? when left on auto the speeds go down drastically
2. i notice that some channels are brutally slow on both bands. like 1.5mbps ? is this normal
3. is this even worth it if the 2.4 band is acting this way?
4. from insider i see that 5.0ghz only connects to two channels isn't suppose to be 3?
My 2.4 GHz is not working corrently on my EA3500 router. I have no trouble with my 5 GHz which I am currently on. On my iPhone I have to manually click the network even though it is known and then the wifi icon lights up full then goes dim then just flashes til it gives up. If I try connecting with my computer it just doesn't load the internet.
View 4 Replies View RelatedHow come my 2.4GHz client can't see my 5GHz client? Shouldn't they be visible through the DIR-825 router?
View 1 Replies View Related