Linksys Wireless Router :: Connecting WAP54G To E2500?
Dec 15, 2011
Is it possible to connect my WAP54G to my new E2500 router?I previously had a WRT54G and had my WAP54G connected to it in AP Client mode. This enabled me to have internet access on my desktop computer that is located in another room downstairs.I would like to configure my WAP54G to work with my new E2500 router in the same way.
View 2 Replies
ADVERTISEMENT
Aug 15, 2012
I have an E2500 wireless N router that I recently bought to replace a cheapie netgear that I lent to family. The router is in the basement near a bunch of metal ducting and I live near a radio station, both of which I believe is killing my signal. Anyways, I was able to pick up a WAP54G wireless access point. I would like to use it as a wired repeater (hopefully to get the signal up into the upper levels of my house). Can I use the WAP54G with the E2500? I looked in the setup page when I was trying to set it up as a repeater, and it says it will only connect with another WAP54G or a WRT54G (linksys wireless g router).
View 6 Replies
View Related
Jan 19, 2012
Is it possible to connect my WAP54G to my new E2500 router?
I previously had a WRT54G and had my WAP54G connected to it in AP Client mode. This enabled me to have internet access on my desktop computer that is located in another room downstairs.
View 2 Replies
View Related
Dec 28, 2012
Is it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies
View Related
Oct 17, 2010
Is it possible to get a WAP54G wireless access point working with a WRT120N wireless router, by wiring the 2 devices together?
View 6 Replies
View Related
Nov 3, 2011
I have just installed an E2000 router in an upstairs office. The signal strength is quite low downstairs so my question is: Can I use a wap54g as a repeater. If so, how do I get the MAC address of the E2000?. The E2000 has two bands and is currently running at 2.4. Would the range increase if I changed the setting to 5.
View 4 Replies
View Related
Dec 22, 2011
I recently installed a refurbished E2500 router. The reported speeds I got when hovering over the icon in the system tray ranged from 54 Mbps down to 1.0 Mbps. Also, it would drop, then reestablish, the connection several times per day.I contacted Tech Support via Live Chat, and got a woman who told me it was due to the fact that I'm using the router with an older system that has a wireless-G card (I'll be getting a new system soon).Of course, I thought that was ridiculous, so I called Linksys Tech Support and got a young man who had me reinstall the firmware upgrade (which I had already done when I installed the router). After that, it was good for about 24 hours, then the problems manifested again.I returned the router and ordered a replacement, also refrubished. Again, I upgraded the firmware upon installation. .
View 4 Replies
View Related
Mar 5, 2012
Have set up Router OK. Created Flashdrive EZ
How do I connect my IPAD now to WiFi since there is no USB port on my Ipad??
View 1 Replies
View Related
Aug 6, 2011
I recenlty bought an E2500 router. I was able to connect 4 of our laptops at home just fine. But when I tried to connect my Acer One netbook, the "Cisco Connect" loaded up to 25% & then I couldn't connect to the internet. I've contacted Tech Support & they suggested downloading the latest wireless adapter driver. I contacted Acer & they said it sounded like a security issue on my netbook. I was out of warranty so they'd have to charge $150 for tech support.
View 2 Replies
View Related
Feb 25, 2012
just replaced my WRT54GL with e2500 and i have a problem connecting my bridge (WET610N) to e2500 router, it connects fine, but no internet when i connect the bridge to another PC (bidrge says it's connected and got IP), same story with another router (WRT54GL) i connect it with the wire to the e2500 than connect to that router with wi fi and OOPS no internet when i connect to e2500 directly with laptop, iphone etc i have the internet connection, but when i connect the bridge or another router i get no internet looks like E2500 does not let the internet pass throught the bridge or other router.
View 3 Replies
View Related
Jan 9, 2012
Just replaced a long-serving WRT54GS with an E2500 to gain a single feature… DHCP reservations for a bunch of web cams around my home. So far, the owner/user-experience with the 2500 has not been as positive as it was for the 54 or any of it's predecessors here and at my business. They just worked when you set them up, and once set up, they stayed set up. Zero futzing around with details. Some issues I'm seeking more expert input on:
My Panasonic Viera DVD/blueray player can access the web. Worked fine on the 54… access "Network" and 50% of the time it would join the network then and the other 50% of the time, you had to try a second time which I presume was the time it took for the device to gain access to the network. With the 2500, you can't ever (so far) get on by selecting "Network"… you have to go into the sub menu and have it dwell in the Network menu where it appears to make an ongoing effort to get onto the network. About 30% of the time, you get on… the other 70% no joy.My HP wireless printer will join the network if you dive into its menu system and tell it to look for the network. However, sitting at any of the computers on the network, you can't "get the printer's attention"… it just doesn't join and the print fails. You go over and use the printer's menu manually to get it on and it stays on for a short time, but it soon quits and that's the ball game.My Google Nexus One phone is a slightly different experience… it goes off the network as soon as you shut the screen down but, it seems like it comes back when you turn it on. With the 54, it seemingly remained in touch with the network better… things came in over the net while it was in my pocket. So, works better than the other two but I don't see why it goes away when on the 54 router, it didn't seem to.
In case it matters, this system is set up with DHCP, WPA2/personal and MAC filtering as was the case on the router(s) it is replacing. UPnP has been disabled. On 1.0.03 of the firmware. There are 6 DHCP reservations which also receive port forwards. I have adjusted the Beacon Interval, Frag threshold and RTS threshold for both frequencies and the MTU, all in accordance with recommendations under the support area for this site. Since everything worked well for both the 54 and its predecessor, I have to believe it's the 2500 that's the problem.
View 3 Replies
View Related
Aug 19, 2011
I just bought an E2500 router, and am only getting a fraction of the speed I do by connecting without it. Both wireless and wired through the router I'm getting about 1 mbps, while without it I'm getting about 10 mbps.
I do live in an apartment, so I'd understand if there were some wireless interference going on, but would that explain away the wired issues too? I've also tried changing the channel (though only of the 2.4 GHz connection), and that's not working any.
View 9 Replies
View Related
Jul 19, 2012
I have a Linksys E2500 and I'm trying to connect it to my ISP provided router (Actiontec V1000H) because I wanted better range and consistent connectivity for my 6+ wireless devices.My problem is that, to make this work, I connected an Ethernet cable from the E2500's yellow internet port to one of my V1000H's LAN ports. This, however, did not give me access to the internet even though the network for my E2500 was available in the network list and selected as the default network. I then had to go the the advanced settings of the E2500, and changed the router IP address from 192.168.1.1 to 192.168.2.2. This granted me internet access.However, everyone i've talked to including coworkers and experts at dslreports said that, because of what I've done I've set up a double NAT with 2 potentially conflicting IP addresses, and down the road weird issues will arise because of it. They also suggested I connect the E2500 to a dedicated modem to avoid this problem. However, the dedicated modem I was sent was faulty and did not allow internet access even through the ethernet connection. So, until I get a new dedicated modem, I have to use the router/modem combo.What should I do? Should I set up the E2500 as just a wireless access point for my existing router/modem combo? What do I need to edit in the advanced settings?
View 6 Replies
View Related
Feb 23, 2013
On my dual band E2500, I have both the 2.4 and 5 GHZ enabled. I have a fairly new HP with an N wireless card but I cannot get it to connect at the 5GHZ frequency. The only computer that will connect at the speed is my wife's with an external Cisco wireless card. What the settings should be on the PC in order to get it to connect at the higher frequency?
View 4 Replies
View Related
Jul 18, 2012
Where I work, we have four computers connected on a network with a Telus combination router and modem (I should probably also mention that two of the computers are connected to a switch which is then connected to the Telus modem/router because that is how the previous tenants set it up) . Recently, my boss wanted to have two different wi-fis, one as a guest wireless and a password one for the employees so he bought a Cisco E2500. I set up the second router as a wireless access point, but eventually we started getting problems with IP conflicts which started messing with the work group connections.
How I'd go about setting up the E2500 properly so that there are no problems like I've been having (having to reset the modem/router constantly for the internet to work, computers being assigned different IP addresses and problems connecting to the server over the workgroup network).
View 1 Replies
View Related
Dec 13, 2012
I want to install wireless router in my home. It is 200 Square metres. Usb port does not meter for me. I want to connect 2 laptop 3 mobile phone via wlan. Which will be better E2500 or E3200 to cover whole area? P.S my internet speed is 40mbps
View 1 Replies
View Related
Nov 16, 2011
I need to go two ways in my house to improve the wireless signal. Do I just run ethernet cable from the router to the access points? Do i then setup each AP?
View 1 Replies
View Related
Jun 2, 2011
I have set my WAP54G up as a repeater for my E2000 but the signal for Guest access is only about 1/2 of the strength of the signal for my network. Is there a way to boost the signal for Guest access?
View 2 Replies
View Related
Mar 12, 2012
I have a WRT54GS v5 running firmware version 1.52.8. When I select the WPA wireless security mode, the encryption technique is fixed to TKIP - I am not given the option to change it to AES? I would really like to be able to select WPA- with AES (this is related to the WAP54G apparently not being able to do do WPA2 - AES in client mode).
View 3 Replies
View Related
Dec 5, 2011
I have a E2500 router and 3 WAP610N access points. Users are having a difficult time connecting to the AP's. The client device just sits there trying to obtain an IP and then times out. If they get within range of the actual wireless router, then connect instantly. Is there a setting to increase that will allow longer time trying to obtain an IP?
I am using the same SSID for roaming, but am using different channels (1, 6, 11) for the overlap. See diagram below. Not sure if this has some impact?
View 4 Replies
View Related
May 15, 2013
At one of our offices, we have a Cisco ASA5505 firewall that has dhcp enabled. I have a WRT54G router plugged into that firewall with DHCP enabled. The scope of our inside network is 192.168.51.***, however when connected to the WRT54G, it gives you the scope of 192.168.1.***We have an antenna amplifier screwed into one of the antenna ports on the router. This whole setup works fine.
The problem is we need to install an access point WAP54G in a building across the property (picks up router wireless signal fine) to repeat the wireless signal to the back of the property where the router will not reach. I have read that all you need to do is type in the wireless mac address of the routher into the access point and select "Wireless Repeater". I have the channels set to 6 on both devices as well as the same security configuration. When I try to connect to the wireless network on the access point, It never gives me an ip in the 192.168.1.*** scope, which the WRT54G is configured to give out. Also, in this setup does the WRT54G need to be set to router or gateway mode? I do not need it to distribute ip addresses. [code]
View 1 Replies
View Related
Feb 1, 2013
The situation is Main house running Linksys EA4200, I have a garage apartment rental that is to far away to receive the wireless guest network.I ran a cat5e to the apartment, can I configure the EA4200 to allow the WAP54G access point to use the guest network? I want to prevent my renters from having access to the home network, but just have basic internet access separate/outside my network.
View 6 Replies
View Related
Mar 1, 2012
I have a wrt54gs v7 and a wap54g v3.1. Both have latest firmware on them. I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address. is that right?). I have them set on same subnet with static ip addresses. They have same wireless ssid and password with one using channel 10 and the other using channel 2. I can receive an ip address from the router and connect to internet. I cannot get an ip address from the access point. I tried a static ip on the computer and it will connect, but I don't have internet. Am I missing something in the setup? Can this access point act as a repeater for this router?
View 3 Replies
View Related
Sep 5, 2011
I'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies
View Related
Oct 4, 2012
I previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
View 4 Replies
View Related
Feb 28, 2013
I am trying to connect to a new VPN using my E2500 router. As soon as I connect, the connection breaks.
View 1 Replies
View Related
Sep 3, 2012
i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies
View Related
Dec 18, 2012
I want to add my E2500 as a second wireless router to cover my entire house.I have a Motorola Surfboard SBG6580 cable modem (Time-Warner) at one end of the house.I added via powerline Ethernet connection a new E2500 wireless router at the other end of the house.The E2500 set-up with all defaults and has the same SSID and Password as the Surfboard cable modem.It seems to work OK, but I wonder about network confusion/interference.Do I have to configure the E2500 in some manner to allow seamless roaming of my wireless devices (iPad, Cell Phones, Netbook)?I had an RE1000 with just the Surfboard, but it did not quite do the trick, and does not like both routers connected at either end.
View 9 Replies
View Related
Nov 23, 2011
How To Reset E2500 Router
View 1 Replies
View Related
Jan 23, 2012
I am trying to setup a WAP with my linksys 2500. I am currently using a Gateway connected to my DSL and am looking to set up the access point through the E2500.
View 1 Replies
View Related
Nov 18, 2011
So, i have a e2500 router and find that every so often, I have to unplug it and reset it because I am losing my internet connection.
View 7 Replies
View Related
Dec 22, 2012
How to set router to use as Slind Box Pro?
View 3 Replies
View Related
Jan 4, 2012
I currently have my E2500 connected via wired LAN (not WAN) port on another router. The E2500 has an LAN IP of 10.0.0.2 and the router has 10.0.0.1 and a dhcp range outside of these. DHCP is disabled on the E2500. I can use my E2500 as a wired access point with no difficulty I plug something in and it calls the router and gets an address, but I can not get DHCP through the wireless of the E2500.
View 2 Replies
View Related