I have set my WAP54G up as a repeater for my E2000 but the signal for Guest access is only about 1/2 of the strength of the signal for my network. Is there a way to boost the signal for Guest access?
View 2 RepliesI have just installed an E2000 router in an upstairs office. The signal strength is quite low downstairs so my question is: Can I use a wap54g as a repeater. If so, how do I get the MAC address of the E2000?. The E2000 has two bands and is currently running at 2.4. Would the range increase if I changed the setting to 5.
View 4 Replies View RelatedI have an E2500 wireless N router that I recently bought to replace a cheapie netgear that I lent to family. The router is in the basement near a bunch of metal ducting and I live near a radio station, both of which I believe is killing my signal. Anyways, I was able to pick up a WAP54G wireless access point. I would like to use it as a wired repeater (hopefully to get the signal up into the upper levels of my house). Can I use the WAP54G with the E2500? I looked in the setup page when I was trying to set it up as a repeater, and it says it will only connect with another WAP54G or a WRT54G (linksys wireless g router).
View 6 Replies View RelatedIs it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies View RelatedWe have a wireless network and would like to extend the range for it and I was told that a E2000 could be setup to extend the range.If we say that our existing wireless network has the SSID network1, can the E2000 be setup so that it is connected to a LAN socket and then wok as a wireless runter with the same SSID (network1) so that pc's can connect easily ?Or must the two wireless routers be connected with a dedicated cable ?Or must I setup the new E2000 up as a new wireless network with a new SSID like network2 ?
View 3 Replies View RelatedJust bought an E2000 router from Cisco. Unfortunately the wireless signal doesn't cover my whole house, so I need to repeat the signal. Which repeater is compatible with this router?
View 4 Replies View RelatedI just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies View RelatedI have a WAP54G as my access point, currently it is connected with my BEFSR81 router. I am thinking of changing the access point to a WAP610N for the house. I know that this would work but I was wondering if the WAP54G could be used as a repeater for the outside (I know a lower speed). I know they are two different channels but I wanted a larger range for my wireless. I am on Windows XP, SP2, using Firefox. Can this be done?
View 4 Replies View RelatedI have WRT54GL and want to setup wap54g as wireless repeater? I need to expand the signal using wap54g
View 1 Replies View RelatedI have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?
View 1 Replies View RelatedI need to extend the wireless range over what I have using an E2000. Can I use a WAP610N in repeater mode? If not can I use a WAP54G knowing that there will be a performance loss? Is there another option to add additional coverage to the existing wireless network?
View 2 Replies View RelatedIs it possible to connect my WAP54G to my new E2500 router?I previously had a WRT54G and had my WAP54G connected to it in AP Client mode. This enabled me to have internet access on my desktop computer that is located in another room downstairs.I would like to configure my WAP54G to work with my new E2500 router in the same way.
View 2 Replies View RelatedI need to go two ways in my house to improve the wireless signal. Do I just run ethernet cable from the router to the access points? Do i then setup each AP?
View 1 Replies View RelatedIs it possible to connect my WAP54G to my new E2500 router?
I previously had a WRT54G and had my WAP54G connected to it in AP Client mode. This enabled me to have internet access on my desktop computer that is located in another room downstairs.
I have a WRT54GS v5 running firmware version 1.52.8. When I select the WPA wireless security mode, the encryption technique is fixed to TKIP - I am not given the option to change it to AES? I would really like to be able to select WPA- with AES (this is related to the WAP54G apparently not being able to do do WPA2 - AES in client mode).
View 3 Replies View RelatedIs it possible to get a WAP54G wireless access point working with a WRT120N wireless router, by wiring the 2 devices together?
View 6 Replies View RelatedAt one of our offices, we have a Cisco ASA5505 firewall that has dhcp enabled. I have a WRT54G router plugged into that firewall with DHCP enabled. The scope of our inside network is 192.168.51.***, however when connected to the WRT54G, it gives you the scope of 192.168.1.***We have an antenna amplifier screwed into one of the antenna ports on the router. This whole setup works fine.
The problem is we need to install an access point WAP54G in a building across the property (picks up router wireless signal fine) to repeat the wireless signal to the back of the property where the router will not reach. I have read that all you need to do is type in the wireless mac address of the routher into the access point and select "Wireless Repeater". I have the channels set to 6 on both devices as well as the same security configuration. When I try to connect to the wireless network on the access point, It never gives me an ip in the 192.168.1.*** scope, which the WRT54G is configured to give out. Also, in this setup does the WRT54G need to be set to router or gateway mode? I do not need it to distribute ip addresses. [code]
The situation is Main house running Linksys EA4200, I have a garage apartment rental that is to far away to receive the wireless guest network.I ran a cat5e to the apartment, can I configure the EA4200 to allow the WAP54G access point to use the guest network? I want to prevent my renters from having access to the home network, but just have basic internet access separate/outside my network.
View 6 Replies View RelatedI have a wrt54gs v7 and a wap54g v3.1. Both have latest firmware on them. I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address. is that right?). I have them set on same subnet with static ip addresses. They have same wireless ssid and password with one using channel 10 and the other using channel 2. I can receive an ip address from the router and connect to internet. I cannot get an ip address from the access point. I tried a static ip on the computer and it will connect, but I don't have internet. Am I missing something in the setup? Can this access point act as a repeater for this router?
View 3 Replies View RelatedI can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View RelatedI would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies View RelatedWe bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies View RelatedSo i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies View RelatedE2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies View RelatedI've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies View RelatedMy internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies View RelatedI have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies View RelatedI'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies View RelatedI have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 Replies View RelatedFor Xbox 360? currently, whether wired or wireless, my Xbox 360's NAT type is strict, and I am unable to do anything online whatsoever. Is there anyways to set up an exception, or anything that can open my Xbox's connection to my router so I can actually use it online?
View 2 Replies View RelatedIm using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?