My 2.4 GHz is not working corrently on my EA3500 router. I have no trouble with my 5 GHz which I am currently on. On my iPhone I have to manually click the network even though it is known and then the wifi icon lights up full then goes dim then just flashes til it gives up. If I try connecting with my computer it just doesn't load the internet.
View 4 RepliesI installed an E4200 in an outdoor patio area where the ambient temperature can be high (Las Vegas area); however, the router is located in the shade without any direct exposure to the sun. After using the router for about 15 minutes, the router is extremely hot and 2.4GHz band will stop working. In addition, even when the router is working, the 5 GHz band connects at much higher speed than the 2.4 Ghz band. The internet download speed is much higher using 5 GHz compared to 2.4 Ghz.
View 9 Replies View RelatedI have a E4200 updated to the latest firmware I have problems with the wifi on the 2.4GHz band, in fact, at power on, many times wi-fi on the 2.4GHz band doesn't work but the 5GHz band works normally. After some reboots the wi-fi operating normally on both bands.
View 9 Replies View RelatedHAve UPnP enabled in the EA3500 but QNAP keep telling me "Your router does not support UPnP protocol or you have not enabled the UPnP function on the router"
View 8 Replies View RelatedJust purchased new N750 model EA3500-NP and everything went ok until I tried to get my HP Laser Jet P2035n online. No go! It worked fine on the D-Link via Ethernet connection.
View 4 Replies View RelatedI purchased a EA4500 and at first I could connect to it through its default ciscoxxxxx ssid on my laptop which is 2.4GHz only. I upgraded the firmware using the PC utility and now I can't find the 2.4GHz SSID no matter what settings I do. I've disabled and enabled it multiple times, changed it to have no security or with security and enabled and disabled it and renabled it. Nothing seems to work, but for some reason the 5GHz side I can connect to using a 5GHz device. I've also tried disabling the 5GHz side, but still no 2.4GHz.
View 4 Replies View RelatedDecided to go with the e4200v2. 199.99 for a router 450 + 450 with a little extra features. very pricey but thought it would be worth it. I got it hooked up with no problems for the first 5 minutes. I have 35mbps down wired from the router and on the 2.4 and 5.0 ghz band about 25 feet from the router was getting just that!! no loss really. However after a few more speed test i noticed it was fluctuating very slow to fast. Also the 2.4ghz was only 144mbps. after getting in the router i changed the 2.4ghz to channel 6 and 5ghz to 153 and changed to 20mhz only on the 2.4 and 40mhz only on the 5.0ghz. Now all is doing well .
1. why am i not able to run the 2.4ghz on 40mhz? when set to auto i have a lot slower speed tests even know it is running on 20mhz only because I'm only getting 144mbps. I don't know why its not running 40mhz ? i don't know why i have to change it to 20mhz only why cant i leave it on auto and if i had a day with little interference it would switch to 40? when left on auto the speeds go down drastically
2. i notice that some channels are brutally slow on both bands. like 1.5mbps ? is this normal
3. is this even worth it if the 2.4 band is acting this way?
4. from insider i see that 5.0ghz only connects to two channels isn't suppose to be 3?
I purchased a e4200 in hopes that its dual band capability would allow us to run a 2.4ghz network for certain devices and a 5ghz for everyone else. I am able to setup the router and connect but it seems when the 2.4ghz network drops the router drops all connections.
At first I had the networks setup with the same ssid, then changed the 5ghz network to a new ssid but was still losing connection when the 2.4ghz network dropped. This may be a simple routing issue i am overlooking (bit of a network newbie).
On my new E4200, I cannot connect wirelessly to the 2.4GHZ band. I can only connect to the 5GHZ band. I know its not the distance because i've got my laptop only 2 feet away. I've hit the refresh wireless network button, but the only network visible is my 5GHZ. I've also restarted the router, no luck
I went into the router settings and made sure that BOTH SSID'S are broadcasting a signal.and are enabled (ive got the channel and other settings set to auto). I'm able to connect perfectly well to the 5GH band, and walk around the house, but nothing i've done, allows me to see the 2.4GHZ band? So far, my wireless reception is poorer than my old wrt310n.
On my dual band E2500, I have both the 2.4 and 5 GHZ enabled. I have a fairly new HP with an N wireless card but I cannot get it to connect at the 5GHZ frequency. The only computer that will connect at the speed is my wife's with an external Cisco wireless card. What the settings should be on the PC in order to get it to connect at the higher frequency?
View 4 Replies View RelatedBoth use the same encryption (WPA2-Personal), same channel and they are tested in the same location with g-only mode. Only one router is switched on at any one time during the test. When 3 g-client notebooks (of various brands) are associated with the E4200, the signal indicator is a single bar, wherelse they can get 3 bars with the WRT54G (in the same location). For Internet speed test on a 20Mbps link, WRT54G is able to substain about 10Mbps, but only 1-2Mbps with the E4200.
Is such difference in performance between the two router models normal? Is there any configuration required to tweak the E4200? Or is it a hardware related issue with E4200?
The E4200 has been updated with the latest available firmware as of yesterday.
Using firmware 1.0.01, has anyone successfully gotten the E4200 to bond two channels using the 2.4GHz spectrum? I just can't get it to bond. I assume it's a firmware issue, yet to be fixed. I've tried settings Auto (20 or 40), and nada. It has never bonded. The 5 GHz bonds fine. There are a few interferences by the neighbours wifi, but nothing substantial that should prevent bonding. I have this router at school too, and the same thing happens there, with the same firmware, so I doubt it's an interference issue. I'm using WPA2 Personal encryption. I tried auto channel, and setting channels to 1, 3, 5, and 11, nothing changed.
I know I'm not bonded because A. Max link speed is ~144Mbps, and B. using a program like inSSIDer tells me I'm only using one channel on the 2.4Ghz spec.
How do I know if I'm using 2.4 or 5ghz? I would like the laptop and ps3/net flix to use the 5ghz and everything else to use 2.4ghz. I used the e3000 CD fro the setup. When I was at the last part of the setup, when it gives you a ssid name and password. I deleted it and typed in a name that I could remember. I clicked the button for the next step and everything was complete. I also received another name for guest to use the computer. The e3000 setup just game me some wild name like running water.
I would like to know since I have two different names, which on e is using 5ghz and which one is using 2.4thz? Can you tell me if the e3000 automatically have the first name use 5ghz and the guest just 2.4ghz on the second name?
2 days ago my e1000 died, so I went big and bought the e4200 (due to newness, its already loaded with Firmware 1.0.03 build 14) to aleviate my networking woes. I'm running into an issue where I'm utilizing both the 2.4Ghz bands and the 5Ghz band. My desktop as an AE1000, and I'm utilizing that on the 5Ghz band. Everything else in the house (Dell laptop, 2x iPhone 4 and an HP printer) are all connecting to the network wirelessly.
I have had 0 network issues with regards to my wired connections, or my 5Ghz connection. But my 2.4Ghz connection will continuously be unavailable. I have both bands set to brodcast, they have different names so my AE1000 can connect via 5Ghz band. Both yesterday evening, and this morning, my phones, laptop and printer cannot connect, and for the most part, the network doesn't show up on available networks. When it does show up, the devices can't connect.I'm proficient enough to do the general home networking, but I'm at a loss as to how to fix this, without a daily reboot of the router (which seems excessive and unwarranted for a 2 day old e4200 [or any router to be honest]).
I just recently (4 days ago) purchased an E3200 router. I noticed some random disconnects on my devices using the 2.4GHz frequency.I installed inSSIDer from MetaGeek to see what was going on and noticed some strange behavior where the Amplitude on the 2.4GHz randomly drops dramatically. Sometimes its once every 10 minutes, other times it happens 5 times in one minute. I can't figure out what is the cause. The 5GHz signal is steady as a rock.
What I tried so far: Set the Channel to the least crowded channel instead of auto, upgraded the firmware, restarted the router all to no avail. This is annoying to say the least. It doesn't affect anything unless you are playing video games or running a remote desktop session, where a single disconnect is disastrous. I just upgraded from an old linksys wrt54g, tried a netgear n600 which was terrible, then swapped it out for the Cisco E3200..
setup an external hard drive with music on on the usb port on my EA3500 and actvated ftp but I cant access it from the net.
View 1 Replies View RelatedFor hours i tried to find info online of how to access QoS on EA3500 router. I cannot find it on the cisco connect cloud page.
View 1 Replies View RelatedSystem:
HP Pavilion dv7-6135dx Ent Pc Win7 Home Prem 64
Motorola Surfboard Modem
Linksys EA3500 Router
Netgear 10/100 24 port switch
my wife bought me this EA3500 for Father's Day this year. It's only been hooked up for a couple of weeks (we were in the middle of a move during Father's Day), but now I have no wifi on either band. My wife can no longer connect to it either. We have tried completely resetting it, we have reset the modem, the switch, laptops, everything. Still no wifi. It worked out of the box, but now we have nothing. Does HP needs a certain type of driver? Our iPhones show connected and surf the brower's and FB app with no issues while in wifi mode, but then again, I can pull the ethernet from the internet port and the phone's still show connected (good job, iOS).Cable from main splitter runs to basement where the modem is located. Modem ethernet feed up a wall to a wall plate where the router is. Router then feeds back to the switch. The switch then sends the IP throughout the house for the LAN lines, and the EA3500 feeds all of the wireless devices (used to). So, Cable box, modem, router, switch. Router is currently good for LAN only. I am connected to it via LAN right now, 2 feet from my laptop.
In connections:IPv4/IPv6 both "No Internet Access" (for IPv4, if you change a setting in the setup, it becomes "Internet Access" for about 3 seconds.)Media State: EnabledSpeed: Alternates between 72Mbps and 144Mbps
In my home network, I have a Synology. It has 10.0.123.123 as local IP address on my local network and it can be accessed by internet with the dynamic domain name.So when I'm home, I have to use 10.0.123.123 to access it, and when I'm away, I have to use trucmuche.diskstation.me.Would it be possible to configure the EA3500 to redirect the domain name "trucmuche.diskstation.me" to 10.0.123.123 when I use the domain name inside my home ?A friend told me that I had to configure "loopback" but I don't know how..
View 3 Replies View RelatedThe guest network on the router keeps going down. It can be seen but it cannot be connected to. Sometimes it works for a day or 2 and then it doesn't. I have to constantly babysit the network and it is entirely frustrating because the only fix is to reboot the router.I have tried factory resetting several times.I have tried re-flashing the fw.I'm using the non-CCC fw because CCC had way, way too many issues.These routers have been out for months and many people have been having issues and somehow Cisco doesn't see fit to work on firmware that stabilizes them at all? It's like, they release a router and then forget about it - the next batch comes along, often the same guts with a different shell and it's the same thing over again. I had a WRT610N and I said I'd never buy another Cisco after that but I broke my rule because of being lured by these "App enabled" features, which mind you have nothing at all over the competition since the CCC doesn't even work for most people.
View 9 Replies View RelatedI have a EA3500 wireless router with the new style (smartwifi) firmware. I've scoured the web admin interface and can't find any sort of 'status' page that would tell me the external IP. I've looked through the support docs but they only show how to find internal/local IP.
View 2 Replies View RelatedI have an EA3500. PPPoE connection. Can't seem to choose my DNS server (use Unblock-US) since the router insistently forces me to use the DNS from ISP.How can i work this around? I'm kinda tired of people asking me why i am changing the DNS. I want to change the DNS and that's final. It's a resource like any other and i want to use it.P.S: i tried most of the basic troubleshooting. I tried my old router back on and the DNS's works fine. I tried even conecting the old router re-routing the new one, and the other router manages the selected DNS's servers fine.
View 9 Replies View RelatedIf someone has the original firmware for the EA3500 to copy. I need to downgrade my router after Cisco sabotaged it with their Cloud Connect. This will be the firmware you have right out of the box. Be sure you go into the Admin. section and Save a Copy before you ever connect to the Internet. Also Uncheck the Auto Updates box or you will be fed the Cloud Connect (and its amazing Terms Of Service).
View 6 Replies View RelatedWindows 7 64 bit / Linksys EA3500 / (2) FosCam F18910W IP Camera’s I just installed a new EA3500. (Should I have purchased the 4500)?I need to set up port forwarding to enable wireless use of the IP cams with my iPhone. I had this all set using my former router, but it died.how to to port forward this Linksys EA3500?
View 2 Replies View RelatedI have recently bought a cisco EA3500 router for my home network and i am pretty surprised to see that a router from the world leader in the networking domain cannot perform as expected.
The first problem i had was that the network (wired and wireless) was dropping from time to time for a couple of minutes with the power led of the router blinking. I turned off the log feature of the router and it seems that until now the problem is resolved.
Now, the second and, at least as annoying as the first, is that i have a 640gb usb hdd connected to the router, formatted NTFS. It seems that every now and then a file gets corrupted, that is, it is transformed into a folder! And it cannot be recovered without pulling out the hdd and using a 3rd parth software for file recovery.
I have the latest firmware. Should i switch back to the classic firmware instead of the "fancy" new one? I really need my files on that drive, so i cannot risk loosing them in this random manner.
I bought the EA3500 nine months ago mainly for the USB port (for a NAS). I recently replaced Comcast Cable with Verizon FIOS. So I now have the FIOS router as my main router (its' IP address is 192.168.1.1). I put the EA3500 in bridge mode to extend the (wired) network. I could get: After going in to bridge mode (with DHCP), I can not log in to the EA3500 (IP address 192.168.1.5 assigned by the FIOS router). I connect my computer directly to one of the EA3500 numbered ports (after various combinations of rebooting EA3500 and rebooting PC). It just continues to say "waiting" and never logs in. Tried choosing a static route (tried both 192.168.1.43 and 192.168.1.5 with 255.255.255.0, gateway and DNS1 = 192.168.1.1) with no luck.Since I can't log in, I cannot set up my NAS on the USB port of the EA3500 (so I haven't gotten far enough to determine if the USB port will even work in bridge mode).Thought about ensuring the latest firmware but since I can't log in I can't do that. (And after a hard reset EA3500 IP address is 192.168.1.1 which creates conflict with FIOS)
View 9 Replies View RelatedI am unable to connect a printer using the USB port on my new Linksys EA3500 router.
I followed the directions here: Support Page , but my verison of Cisco Connect does not have the option to "connect a USB printer".
I am on a macbook pro running OSX 10.7.4 and my verison of Cisco Connect is 1.4 (12005.2). My router's firmware version is 1.0.30.126544. A screenshot of what I see after clicking "add a device" in Cisco Connect is below. The printer is an HP DeskJet F4280.
after updating to smart wi-fi I can't access the USB FTP or off network.Only way it's accessible is from the computer the router is attached to via network drive.FileZilla gives me this error....."Connection attempt failed with "ECONNREFUSED - Connection refused by server".I've reset the router same problem.
View 9 Replies View RelatedAfter using the newest firmware for CCC, I've found it is very convenient, but only in some ways. Now, I think I find it is uncomfortable, very disappointed and waste lot of times. Each time I try to access to CCC, it took me like 5 mins to access the web page. I understand ciscoconnectcloud.com is use when you are outside of your home network, but when I access it directly from my home (local IP), why should I need to connect via a CCC(?) I want a local connect to my router which is a faster access than via a server.
Sometimes, connect via an IP of the router, it say can't connect because of internet connection down, but actually I can still access internet except access my own router. I like the easy setup of CCC but maybe I need to switch back to non-CCC?
I bought a new router today because my WRT54GL was giving me some fits. I purchased an EA3500 and I'm using an EA2500 adapter on the desktop since the router can't reach it via ethernet. Some of my early troubles with this combo began with not being able to test upload bandwidth. It would just time out and give an error via the built in Cisco (OOKLA) utitliy and through speedtest.net after which, the network would show no internet access and I'd have to reset the adapter. After trying to troubleshoot that issue it grew into zero internet access for my desktop however my Nexus would have wifi access without issue. If I'd startup in safe mode with networking I'd have net access shortly and then it would quit about 30 seconds after startup. I've tried uninstalling all drivers for the wireless NIC and the Cisco Connect software while doing everything manually but nothing changes. This PC simply won't gain internet access with the EA3500 or even allow me to access the router through the default gateway IP. I've since put the WRT45GL back in place and I have access again with my EA2500 adapter. I should note that with the EA3500 in place, if I disconnected from my wireless I couldnt see any networks until I unplugged the adapter and reinserted it into the USB port (i've also tried many different ports). I've named the SSID's of the two routers differently, tried a manual setup of the wifi, tried the CD setup, the wifi protected setup, no security, and WPA2 to no avail. I can't seem to get the EA2500 adapter and the EA3500 router to get along. I'm running W7 x64 Pro.
View 6 Replies View RelatedI've recently purchases a Canon MF3010 Multifunction printer, and connected this to my EA3500 router's USB port. Used Cisco Connect to setup the printer, and the print function is working fine.
The issue is with the scan function. It appears the default functionality of the router is to only activate the connection to the printer when a print job is fired off. When this connection is active, the scan functionality works fine.
Another way to activate the connection to the printer to allow for scanning would be to go through
Cisco Connect>Computers and devices>PrinterWhile the process is running (searching for printer), the connection is active as well, and scanning works fine. When the process is closed, scanning no longer works, with an error message stating that communication to the printer cannot be established.
Is there a simpler way to keep the connection to the printer active, or some sort of configuration to automatically establish this connection for scanning?
I have an HP Veer Webos phone. Since I upgraded to an EA3500, I haven't been able to connect my phone to the network wirelessly. Today I temporarily installed a WAP54g on the network, and I am able to connect the Veer via the WAP. I spent 45 minutes chatting with Cisco Support today, but didn't resolve the problem. I believe I have the same situation with an HP Touchpad, but can't say the problems are identical, since its battery is down right now.
[code]....
Its not even listed as a download on the official page of the router. How can i see the notes?
View 9 Replies View Related