Linksys Wireless Router :: E4200 Disabling SSID Broadcast For Both 2.4 And 5GHz Stops Blinking
Jul 1, 2011
I was quite excited about E4200 I got yesterday. Everything works perfect except front LED light start blinking a few hours later. Don't know why it happens in a sudden and non-stop. After several tries, I found that disabling SSID broadcast for both 2.4 and 5GHz stops the blinking.Of course, before doing that, I upgraded firmware to 1.0.02, reset to factory defaults and finally set up E4200 manually rather than using Cisco Connect. Now the LED light is continuously lit.
View 4 Replies
ADVERTISEMENT
Oct 25, 2011
I just set up a brand new LinksysE4200 router at one end of my home, and a Linksys RE1000 range expander at the other end in order to provide full WiFi coverage to my entire house. Everything is working great except for one important detail.. There is currently no way to disable SSID broadcast on the RE1000 range expander! I just flashed it with the latest firmware (v1.0.01 build 2, Jul 22, 2011) , but I'm still unable to disable it, even though it is disabled on the E4200 from which it's receiving the signal it's rebroadcasting. I am seriously considering returning the RE1000. Linksys. add the ability to disable SSID broadcast on the RE1000 in a (not too distant) future firmware upgrade! As far as I'm concerend, this is a MUST HAVE feature in order for this product to even be considered for use in any sensitive network environment.
View 2 Replies
View Related
Dec 30, 2011
I had a e4200,and i used 5ghz wireless.i can't set it to channel 149 or other high channel,my old wireless ethernet card can only support that.make the next version of the firmware can setting 5ghz channel to channel 149、153、157、161.
View 2 Replies
View Related
Nov 20, 2012
I got E4200 v.2 with the latest cloud firmware. On the previous (non-cloud) firmware there was an option to enable or disable SSID broadcast, and I disable it. Now I want to enable it back, but can not find this option in Cisco Connect Cloud. how to enable SSID broadcast on the E4200 v.2 with Cisco Connect Cloud firmware?
View 1 Replies
View Related
Jan 26, 2012
E4200 not letting my known wireless devices connect when SSID Broadcast is turned off.
View 1 Replies
View Related
Nov 1, 2011
Everytime I disable SSID Broadcasting 2 extra wireless connections appear available connections list. (See wirelessconnections.jpg) One is blank and one is labeled Other Network. They disappear when I enable SSID Broadcasting. I am not sure why this is happening.
View 5 Replies
View Related
Dec 29, 2012
F9K117 - I can't see my broadcast ssid for the 5ghz band. Is there anything I can do?
View 3 Replies
View Related
Jul 17, 2011
I've had the wireless G adapter for a year now, and connections work with both 2.4GHz and 5GHz G connections. I just bought a wireless N adapter (2.4GHz and 5GHz capable), and cannot get an N connection.. On 2.4GHz it connects to G only. And on 5GHz, I don't even see the whole band to connect to it.
I've tried disabling the 5GHz band on the E3000, then even setting the 2.4GHz band to no security. I still get a G only connection.My laptop can connect to 2.4GHz and get 144Mbps N speeds.Router is at latest firmware.I've researched this online, but can't find anything concrete.
View 7 Replies
View Related
Nov 21, 2012
How can you disable SSID broadcast on EA6500 wireless network.
View 4 Replies
View Related
Jul 28, 2011
How do I disable the broadcast of my SSID? I do not want wireless. I only bought this router to hook up two computers to the internet via Ethernet cable.
View 9 Replies
View Related
Mar 21, 2013
EA3500, I'm using the Smart Wi-Fi interface through a browser. How do I make my router broadcast the SSID? I think it was when I was setting up using the old interface, before updating the firmware, that I set it to *not* broadcast the network name. Now I feel like I've been all through the menus twice on the Smart Wi-Fi interface, and can't find the on/off toggle.
View 9 Replies
View Related
Nov 8, 2012
Can the broadcast be disabled on EA6500?
View 1 Replies
View Related
Sep 10, 2012
I have found that if I do not enable the broadcast SSID option on my 5GHz N network that my devices will forget the network and not reconnect on their own. Yet, I have the 2.4GHz G/N network set up to not broadcast my SSID and I have no problems. Why can't I disable my SSID broadcast on the 5GHz N network without these problems?
View 9 Replies
View Related
Dec 25, 2012
None of my wireless devices (Windows, iphones) can see the SSID from the 5ghz channel on my E2500. I have updated the firmware and reset the router to factory defaults. Still not visible. The router is set up to broadcast the SSID under wireless settings. Also, selecting "other" under iphone>settings>wifi and entering the SSID name and password gets "could not find the network (ssid)". This was working until a couple of days ago Comcast power cycled the router to make sure my cable modem was working. Now nothing.
View 2 Replies
View Related
Feb 22, 2013
I am the latest firmware of EA2700 but why I can't find there is disable broadcast SSID function?
View 1 Replies
View Related
Dec 1, 2011
why my SSID still displays even though I have the SSID Broadcast "Disabled" for 5 GHz and 2.4Ghz configurations. The name of my network shows full signal strength and a lock next to the name but I was under the impression if I have disabled the SSID broadcast it shouldn't show up at all and would force a user to manually input the network name when trying to connect to it. I have the router configured to only allow certain MAC addresses wireless access as well. Router is running Firmware Version: 1.0.03.Also, my primary computer my iMac running 10.7.2 boots up or is brought out of sleep mode I constantly need to go up to the top of my screen and re-select my network.
View 4 Replies
View Related
Jul 1, 2012
I've recently purchased the E2500, done the setup but am facing some issues.I'm unable to see the 5GHz channel SSID, I can only see the 2.4GHz channel SSID.Have tested all the laptops and devices at home and all can't see the 5GHz channel.The list of devices are:
a) iPhone 3GS
b) iPhone 4G
c) iPhone 4GS (some sites says it doesn't support, some says it does, I'm confused as a result)
d) Samsung laptop
e) Dell laptop
f) Momo11 Little Bird Edition tablet (Made in China [MIC])
g) No name MIC tablet
Secondly, is there any tips / tricks to tweak the modem to increase the internet speed?
View 1 Replies
View Related
Sep 26, 2011
I have a Linksys E4200 router with firmware version 1.0.02. I am using a Macbook Pro. I can connect to a VPN server with the default VPN client software, but it kills my internet connection and disables connecting to SMB
View 5 Replies
View Related
Sep 7, 2011
i have a e3000 set up with my network i have guest network set up through the cisco connect but dont see a field to change the guest network broadcast ssid so an ideas?
View 1 Replies
View Related
Aug 21, 2011
I have e4200 router set up with different SSIDs for 2.4ghz and 5ghz. My laptop (Lenovo x220 with Intel 6205 wireless adapter) can't see the 5ghz network. I've tried changing the channel for the 5ghz network and it didn't fix the problem.
View 9 Replies
View Related
Jan 25, 2011
Some routers are able to forward to broadcast directly by sending a port to 192.168.1.255, other's I've been able to trick by forwarding to 192.168.1.254 and then editing the arp table with 192.168.1.254 <-> ff:ff:ff:ff:ff:ff. Is there any way I can edit the arp table of the E4200? Is there a way to telnet in or get a console connection?
View 9 Replies
View Related
Feb 21, 2012
I ended up with an RMA for a new E4200 ver. 1 and the problem I have still persists. My 2 GHZ WAP gets 65Mbp/s to its connected devices. However, the 5.4 GHZ WAP gets 48 to 54 Mbp/s only.My laptops have Windows 7 and Ubuntu. The WiFi cards are Intel Centrino Advanced-N 6200 and 6230. Both fluctuate at 48 - 54Mb/s on the the 5.4GHZ channel.
If I put it on Wireless-N only, the laptops cannot connect. I have tried AUTO detection for mhz and channels. I have tried 40mhz with channels 149 and 161 with no difference.Currently, I am operating both WAPs on different SSIDs to make sure my results are separate.Security for both WAPs is WPA2-Personal with a 10 digit sequence.
View 9 Replies
View Related
Oct 23, 2011
Router: E4200
Router Firmware: 1.0.03 (Latest FW)
Why I cannot go to the 5Ghz band to utilize the superior speeds to transfer files over wireless connection between my computers? I am sure that I am still on the default 2.4 Ghz because
1) The file transfer speeds are pathetic
2) In Wireless Security, if I set the Wireless Mode to disabled for the 2.4Ghz band, Windows shows me "Unsecured Network" even with 2.4Ghz disabled.
View 9 Replies
View Related
Jun 23, 2011
I bought an e4200 about 2 months ago. It worked perfectly for 3 weeks. Then all of the sudden, the 5ghz connection started dropping. Then it's disappeared completely and it would not show up in a network search. Then the 2.4 ghz started going crazy. I reset it completely, that didn't work. I let it sit for half a day, nothing. I sent it back to newegg and got a replacement. When the 2nd one came in, it worked fine until the next day. 5ghz cut out. I called linksys support and they were no luck. I reflashed to 1001 firmware and it mysteriously came back to normal. It was working perfect until today. 3 weeks later. 5ghz went out, and never came back. I reflashed 1001, nothing. Reset, nothing. Flashed the new 1002 firmware, nothing. 2.4ghz still kind of works, but the speed is barely 5mbps. I'm at a freaking loss right now. This was the best performing router I have tried, of all the top models available right now
View 8 Replies
View Related
May 25, 2012
I just upgraded my in-laws network from a WRT54G to a E4200. It's working but I'm getting issues with the 5Ghz end. I've got both SSIDs using different names.. so its clear which I'm connecting to. I have a macbook pro which has N support and can see the 5GHz SSID.The issue I get is that when I connect to the 5Ghz SSID, the laptop cannot ping or connect to LAN clients on the 2.4GHz end. This includes SMB shares, a couple of devices with web interfaces and one machine running a VNC server. There is also issues with Internet access.. but only sometimes.
Say I have two terminals open.. one pinging Google and the other pinging one of the 2.4Ghz clients. If I connect to the 2.4Ghz SSID, I get both pings working fine. If I switch to the 5GHz SSID, the macbook gets its IP address but then the Google ping will work but the internal ping just keeps failing. The Internet issue.. looking back on the above example.. sometimes the Google ping will also fail. The mac also sometimes indicates that there is no Internet connection behind the wireless connection when this happens.
When I connect on the 5Ghz SSID, I get my LAN IP address from the router (ifconfig). I can also see the /etc / resolve.conf correctly populated on the macbook with thge gateway and DNS settings.For now, I'm just going to get them to only use the 2.4Ghz SSID and assume that a later release of the softeware will fix things.. it could be a compliance issue on the Apple/Cisco N support.
View 9 Replies
View Related
Jan 28, 2012
I setup my E4200 v2 with different SSID's for 2.4 and 5GHz modes. I have no problem with a 2.4 Ghz connection on my laptop, but I cannot connect to the internet in 5GHz. mode. I choose the 5 GHz SSID and enter the passphrase but no luck, even though I have a full 4 bars inthe wireless icon.
View 4 Replies
View Related
Feb 15, 2012
I have an e4200 set up using a trendnet TEW-684ub. Connection on 2.4Ghz and 5Ghz seems fine, but when the 5Ghz network is under load, such as running speedtest, the network drops for a second. This does not appear to happen on the 2.4Ghz network.
2.4Ghz and 5Ghz networks are set to Auto width and channel using WPA2 and I've tried raising the router up a bit to increase airflow to try to eliminate overheating as a possible issue. I'm also running the latest firmware...1.0.0.3, I believe.
View 5 Replies
View Related
May 24, 2012
My network is discoverable, but my machines will not connect (they were connected previously). They can connect to the 2.4gHz network, but not the 5 (I use the 5 for streaming media and gameplay). Windows 7 says it's unable to connect.
View 8 Replies
View Related
Jul 27, 2011
Roku tech support confirms the new Roku2 XS has a 5GHz (as well as 2.4GHz, or course) radio that supports n. I can connect no problem on 2.4GHz Mixed using WPA2 Personal, but not on 5GHz Mixed using WPA2. The Roku can't even see the SSID being broadcast. I don't have any other gear with a 5GHz radio to confirm the E4200 is actually broadcasting a 5GHz SSID.
View 3 Replies
View Related
Oct 15, 2011
2 days ago my e1000 died, so I went big and bought the e4200 (due to newness, its already loaded with Firmware 1.0.03 build 14) to aleviate my networking woes. I'm running into an issue where I'm utilizing both the 2.4Ghz bands and the 5Ghz band. My desktop as an AE1000, and I'm utilizing that on the 5Ghz band. Everything else in the house (Dell laptop, 2x iPhone 4 and an HP printer) are all connecting to the network wirelessly.
I have had 0 network issues with regards to my wired connections, or my 5Ghz connection. But my 2.4Ghz connection will continuously be unavailable. I have both bands set to brodcast, they have different names so my AE1000 can connect via 5Ghz band. Both yesterday evening, and this morning, my phones, laptop and printer cannot connect, and for the most part, the network doesn't show up on available networks. When it does show up, the devices can't connect.I'm proficient enough to do the general home networking, but I'm at a loss as to how to fix this, without a daily reboot of the router (which seems excessive and unwarranted for a 2 day old e4200 [or any router to be honest]).
View 2 Replies
View Related
Jul 10, 2011
U just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?
View 2 Replies
View Related
Oct 5, 2011
I just bought the E4200 routher at best buy a few weeks ago. I got it all setup how I want it. Its been working fine then about a day ago it started to stop working at random. All internet just stops working. Wired and Wifi. I have to either wait for it to work again or restart the router.
View 7 Replies
View Related
Mar 21, 2013
Canada
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]
Is it possible to disable broadcasting that the WDR4300 is made by TP-Link? I want to continue to broadcast the SSID but not the manufacturer. I have looked in the various menu pages and cannot figure out how to have this happen.
View 14 Replies
View Related
