I have found that if I do not enable the broadcast SSID option on my 5GHz N network that my devices will forget the network and not reconnect on their own. Yet, I have the 2.4GHz G/N network set up to not broadcast my SSID and I have no problems. Why can't I disable my SSID broadcast on the 5GHz N network without these problems?
View 9 RepliesNone of my wireless devices (Windows, iphones) can see the SSID from the 5ghz channel on my E2500. I have updated the firmware and reset the router to factory defaults. Still not visible. The router is set up to broadcast the SSID under wireless settings. Also, selecting "other" under iphone>settings>wifi and entering the SSID name and password gets "could not find the network (ssid)". This was working until a couple of days ago Comcast power cycled the router to make sure my cable modem was working. Now nothing.
View 2 Replies View RelatedWhat Radio Channels are available for selection when operating the EA4500 in Wireless-N (5 GHz) mode only? I need to find a router that can be specifically set on channel 120 in the UK
View 8 Replies View RelatedI've recently purchased the E2500, done the setup but am facing some issues.I'm unable to see the 5GHz channel SSID, I can only see the 2.4GHz channel SSID.Have tested all the laptops and devices at home and all can't see the 5GHz channel.The list of devices are:
a) iPhone 3GS
b) iPhone 4G
c) iPhone 4GS (some sites says it doesn't support, some says it does, I'm confused as a result)
d) Samsung laptop
e) Dell laptop
f) Momo11 Little Bird Edition tablet (Made in China [MIC])
g) No name MIC tablet
Secondly, is there any tips / tricks to tweak the modem to increase the internet speed?
I set up my new EA4500 last night, and configured the 5Ghz and 2.4Ghz bands with separate SSIDs (as recommended). While I can see the 2.4Ghz band with all of my devices, I cannot see the 5Ghz band with any of them.I followed the advice given (including the settings shown) on the EA4500 FAQ.Title: Personalizing and connecting to the 5 GHz wireless band on a Linksys Wireless-N routerArticle ID: 21466.Did that *multiple* times, and still nothing. I do have a dual-band capable adapter (Netgear RangeMax WNDA3100 Dual Band Wireless-N Adapter) that I know works on 5Ghz (because I had it working on my old dual-band WDNR3700v1). Similarly, I have PCs sitting less than 20 feet away that were previously able to see the 5Ghz band on my old router, but are now unable to see it on the EA4500.
View 9 Replies View RelatedI was quite excited about E4200 I got yesterday. Everything works perfect except front LED light start blinking a few hours later. Don't know why it happens in a sudden and non-stop. After several tries, I found that disabling SSID broadcast for both 2.4 and 5GHz stops the blinking.Of course, before doing that, I upgraded firmware to 1.0.02, reset to factory defaults and finally set up E4200 manually rather than using Cisco Connect. Now the LED light is continuously lit.
View 4 Replies View RelatedI had a SSID name conflict with one of my devices and the router. I changed the routers SSID which eliminated the conflict. I noted that after changing the SSID, the name of the FTP server did not update to the new SSID. Is this an issue? I did not see any way to manually edit the FTP name. FTP works fine as is.
View 1 Replies View Relatedjust bought the EA4500 new, setup the router with computer plug-in RJ45, after I change my network network to "LinksysOne", I can connect to the network wireless. But when I connect it with hard wire/RJ45, it shows "cisco27205", but I cannot see "cisco27205" with wifi, neither with RJ45 connection cannot see "LinksysOne". Why this happen? is this normal?
View 1 Replies View RelatedI purchased what I think is a new EA4500 but the box was not sealed. On setup it had a SSID name of Mischief Dolphin populated with a random password. Is this a default or was perhaps this router already setup (used)
View 2 Replies View RelatedThe EA4500 web-settings application asks for a username and password. The username is "admin" and the password is my long (60 character) wpa key. I see where I can change the password but it says I'll lose all wireless connections. This doesn't make sense to me. I would think the router administration username and password are completely separate from the ssid and wpa key. This was the case with my earlier LinkSys router. I'd like a router administration username to be something other than the generic "admin" and a password that is easier than my long wpa key. I want a separate ssid and wpa key (what I currently have).
View 2 Replies View RelatedUsing CCC with EA4500, where do I find the control for enable/disable broadcast of the SSID?
View 5 Replies View RelatedI'm looking for a way to connect to my neighbors wireless connection... I have been using it for a while and then he hid his SSID and now, his connection is listed as an Other Network.I found out his MAC address, but I'm wandering is there a way to connect to the wireless network or just to find out that hidden SSID?
View 1 Replies View RelatedI want to search hidden ssid names means non broadcast ssid.
View 2 Replies View RelatedAfter a firmware update the DAP-1522 HWversion A will not connect to a Hide SSID.
I am Using the DAP-1522 as a Bridge in 5Gz.
I recently changed my ssid name from the default "dlink" to a more unique one. The problem is that the router is still broadcasting the default ssid along with the new one. Guest zone is disabled and the new ssid is hidden. But the default ssid is not hidded. Using wpa2 with aes, hardware ver. A1/A2 Firmware ver 1.21. How to remove the "dlink" ssid?
View 4 Replies View RelatedWe have three Access Points, two Cisco Aironet 1260 and one 1240AG. Originally, the SSID was hidden on all three AP's and users had to go to Other Networks and type in the SSID and password to access the WAN. About a few months ago, the network started broadcasting to the public. I am trying to make the SSID hidden again. I have tried going to the Security tab, choosing the SSID Manager and setting single guest mode to none but it has not worked.
View 4 Replies View RelatedI'm wondering if there are other hidden E4200V2 menus.
I didn't think the advanced wireless settings were there on this router, but they are and are accessible by an URL: [URL]
I'm wondering what else is actually in there and not on the web GUI?
Has anyone discovered any other portions of the firmware that are hidden and accessible via an URL entry?
I'd like to set up a 2.4Ghz and a 5Ghz SSID at the same time, using one Cisco AP541N-E-K9. But I can't figure out any way to do so.
View 1 Replies View RelatedIs there any way to make networks hidden through the WiFi Smart software? I have a Cisco Linksys E4200V2. I have gone through everything to try figure out how to make my S.S.I.D. to not be broadcasted, but seems like the only way to make it hidden is to use the Origonal Firmware make it as hidden, then install the New Firmware and software. Seems like Cisco may have missed this option. I do know a lot of people would prefer their Networks hidden for a little security. I know it isn't much, cause if someone wants to get that info it's not hard to get it. But for people who don't know or don't want to waste all the time to find the Hidden Network name can be turned away, for going through that extra step.
View 6 Replies View RelatedF9K117 - I can't see my broadcast ssid for the 5ghz band. Is there anything I can do?
View 3 Replies View RelatedI have e4200 router set up with different SSIDs for 2.4ghz and 5ghz. My laptop (Lenovo x220 with Intel 6205 wireless adapter) can't see the 5ghz network. I've tried changing the channel for the 5ghz network and it didn't fix the problem.
View 9 Replies View RelatedI am using the E2500 with the Wireless N-pci adapter with dual band, both with the latest drivers / firmware, and I am getting extremely low signal quality and connection speed when connecting to the 5 Ghz network.My computer is no more than 15 feet away from the router, and on the same level. I also verified the connection with the 2.4 Ghz band, and it reads as excellent, and with 54 mps. Using 5 Ghz I get one bar of signal quality (very poor) and no more than 13 mps connection speed.
View 9 Replies View RelatedWednesday, November 23, 2011I have an Airport Extreme dual-band 2.4Ghz and 5Ghz. Each network is has a different name and different password so I know exactly which one I am connected to.On a MacBook Pro, it sees both networks. On a Dell E5520 it will see both networks. On an iPhone 4 it will see both networks. I can connect any of these devices to either network.Just got the Linksys E3000 dual-band 2.4Ghz and 5Ghz. Each network is has a different name and different password so I know exactly which one I am connected to.On a MacBook Pro, it sees both networks. On a Dell it will only see the 2.4Ghz network. On an iPhone 4 it will only see the 2.4Ghz network.The Airport Extreme is powered off when using the E3000 so I know there is no interference from this router.E3000 Firmware Version 1.0.04. It's the latest.5Ghz Wireless Settings Network Mode: Mixed Channel Width: Auto (20Mhz or 40Mhz) Channel: Auto (DFS) 2.4Ghz Wireless Settings Network Mode: Mixed Channel Width: Auto (20Mhz or 40Mhz) Channel: Auto (DFS)Did not mess with any other settings. I have rebooted the computer, cycled the router and modem 3-4 times.Nothing works.My question is since both laptops and phone can see the 5Ghz network when running the Airport Extreme, why doesn't the 5Ghz network show up on the Dell and iPhone when running the E3000.
View 5 Replies View RelatedMy channel width is Channel Width is 40 mhz only, and my channel is Auto DFS?These seem like good settings?My macbook air sometimes see's my 5ghz wireless SID, and sometimes it connects to it, but i still have no internet access for some reason
View 3 Replies View RelatedI've found a few people with this problem on the internet. I'm using my phat 360 with the black N adapter. e2500 is updated to the latest firmware. But my 360 cannot connect to the 5ghz N, only 2.4ghz g. The wierd thing is that the 5ghz signal gives a better signal than the 2.4ghz.
I just found a thread on google talking about the e4200 and someone mentioned counterfit adapters and problems with them. I did buy this on ebay for a cheap price, so it looks like it was too good to be true. this is a counterfit? It does have a real hologram on it.
[URL]
If this is real, what else could be the problem. Has the firmware not been updated to support the 360?
EA2700v1 WPS-PIN using 5GHz does not work. This router includes WPS header in its 5GHz beacon and probe response but the router removes the WPS header from them once WPS-PIN starts. There is no problem with WPS-PIN using 2.4GHz.
View 1 Replies View RelatedEA6500 5GHz band only four channels (36,40,44,48), the lack of 149,153,157,161 channel, firmware Ver.1.1.28.146072, how to add 149,153,157,161 channels?
View 3 Replies View RelatedI ended up with an RMA for a new E4200 ver. 1 and the problem I have still persists. My 2 GHZ WAP gets 65Mbp/s to its connected devices. However, the 5.4 GHZ WAP gets 48 to 54 Mbp/s only.My laptops have Windows 7 and Ubuntu. The WiFi cards are Intel Centrino Advanced-N 6200 and 6230. Both fluctuate at 48 - 54Mb/s on the the 5.4GHZ channel.
If I put it on Wireless-N only, the laptops cannot connect. I have tried AUTO detection for mhz and channels. I have tried 40mhz with channels 149 and 161 with no difference.Currently, I am operating both WAPs on different SSIDs to make sure my results are separate.Security for both WAPs is WPA2-Personal with a 10 digit sequence.
I had a e4200,and i used 5ghz wireless.i can't set it to channel 149 or other high channel,my old wireless ethernet card can only support that.make the next version of the firmware can setting 5ghz channel to channel 149、153、157、161.
View 2 Replies View RelatedI purchased the linksys 3200 dual band router recently. I am a huge cisco and linksys supporter so for me this is disappointing. Aside from being slower at times than my previous router I am having issues with the 5Ghz wireless. My issue I am facing is it seems multiple times throughout the day the router somehow drops its 5ghz wireless ssid or its gone..not sure. The only way I can get it back up and running is to reconnect with the Cisco Connect software and re-establish the settings and then reconnect any wireless devices. This seems to happen sporadically and is insanely annoying considering this router should be a big upgrade.
It seems to me the 2.4Ghz band seems to be more stable. I am on the latest firmware for the device and I am using a 5ghz compatible wireless device to connect to it.
Router: E4200
Router Firmware: 1.0.03 (Latest FW)
Why I cannot go to the 5Ghz band to utilize the superior speeds to transfer files over wireless connection between my computers? I am sure that I am still on the default 2.4 Ghz because
1) The file transfer speeds are pathetic
2) In Wireless Security, if I set the Wireless Mode to disabled for the 2.4Ghz band, Windows shows me "Unsecured Network" even with 2.4Ghz disabled.
I have the E4200. I have two networks, a 2.4 for internet, and a 5gHz for media. I want to have a wired connection to the 5gHz network as some of the media is on my PC. However, it seems I can only have a wired connection to the 2.4gHz network. Is there any way to do this?
View 3 Replies View RelatedI have an E4200v2 configured with an n-only 5GHz network and a mixed 2.4GHz network. Our MacBooks and iPad connect to the 5GHz network, and everything else (iPhones, TVs, etc) connect to the 2.4GHz network. If I disable "WMM" on the QoS screen, nothing can connect to the 5GHz network. Those same devices can connect to the 2.4GHz network, but not the 5GHz. The MacBooks, for example, get a connection timeout error, and the iPad just says "cannot connect." This doesn't seem quite right. I don't absolutely need to disable WMM, but I wanted to make sure that normal WiFi Internet traffic didn't get priority over local wired Mac->AppleTV streaming or voice calls from our wired Vonage box.
View 2 Replies View Related