I recently changed my ssid name from the default "dlink" to a more unique one. The problem is that the router is still broadcasting the default ssid along with the new one. Guest zone is disabled and the new ssid is hidden. But the default ssid is not hidded. Using wpa2 with aes, hardware ver. A1/A2 Firmware ver 1.21. How to remove the "dlink" ssid?
View 4 RepliesAfter a firmware update the DAP-1522 HWversion A will not connect to a Hide SSID.
I am Using the DAP-1522 as a Bridge in 5Gz.
im having a problem on my DIR-655, i just recently updated my DIR 655 2.03NA(which is no problem at all) to 2.10NA, & im having problem on my GUEST ZONE wireless network everytime i connect my Iphone 4 to it every second 10 seconds it goes on & off & i try to connect to the main wireless network it was working fine any causes to this?
View 14 Replies View RelatedI have disabled the internal DHCP/DNS server in the routers firmware. I have enabled the wireless guest access SSID. A client associating with the Guest Wireless Access will obtain a DHCP address from the server in the LAN zone, but cannot resolve DNS as the firewall prevents traffic to flow from the Guest zone to the LAN zone, as it should.Is there a way to enable the DHCP server and DNS server in the routers firmware, but only on the Guest Zone? Is it possible to get the Guest Zone to have a different subnet?Tech support has hung up on me twice now.
View 5 Replies View RelatedI'm wondering if there is a way to prioritize traffic on the router's main WiFi over the guest zone or if there is a way to limit the bandwidth on the guest zone.
Ideally, I'd like to keep a locked primary WiFi for high-speed usage (I know, nothing it really ever secure) and an open guest zone for low-speed usage to whomever wants it. As far as I can tell, the DIR-655 doesn't support this kind of configuration.
I recently picked up a 655 with hardware version A2 and flashed to the latest firmware. I have a HotBrick router. I only want to use the 655 as an access point AND especially to use the Guest Access or Guest Zone feature to allow visitors to bring their laptops and not virus up my network. My home network is open among a few computers for things like SageTV, file serving, etc.I can get the 655 to function just fine as a standard access point by following the instructions to turn off UPNP, DHCP, etc. as outlined in the manual. I then enable the Guest Access/Zone feature, and of course give it a different SSID name, make sure it's on 24 hours a day, that it is enabled, etc.
But, none of my computers can access the internet via the Guest Account feature, just the regular wireless portion. They show connecting to the Guest Account name, etc. but no internet. I've disabled every security feature I know of to test this. Again, the "regular" WAP tests great, but no Guest Account, which is really important and one of the main reasons I bought the unit.I'm wondering - does the Guest Account feature only work if the 655 is the main router, has DHCP enabled, etc.? Does it have to be the one and only router? If so, I'm in trouble, because I can't really give up my HotBrick due to failover features, etc.
Have DIR-655, HW A3, F/W 1.10. On the Advanced tab, there is no Guest Zone option. Can this be fixed with a firmware update? If so, which one?
View 2 Replies View RelatedI am thinking of getting the DAP-1522 access point but I wondered. Can I set it to broadcast on 5GHz for my laptop and ipad, so they can stream video. Then set the guest zone to broadcast on 2.4GHz just for my lame printer, my printer does not have LAN and only wireless b & g. If I do put the printer on the guest zone and I enable routing between zones, will my laptop be able to print to my printer?
View 1 Replies View Related207.NA Firmware, B1 Hardware in use on a DIR-655, Time Warner Cable setup. Nothing to do with Revision, cordless phones,I saw this asked once before specifically here, but it was never answered.After several attacks via our cable network and neighbors, we've HAD to turn on MAC filtering. There are TONS of devices attached normally so two situations popped up:
#1: What happens when you max out the authorized MAC address listings? Does the page get longer when you save/reboot it? Do I have to do it manually from there forward and where can I get down to the core programming level to edit the code and put the MAC's that are around and on 100% of the time to open up the plug-in list on the GUI?
#2: Guest Zone - we NEED a way to have random guests get on our Network with a different password we can randomly change to prevent the outside abuse, etc. but am I understanding what little else has been posted that the MAC filtering also covers the Guest Zone and therefore I have to stick them in there before they could simply log on with the current password? Is there any way to change/stop that without eliminating MAC filtration as a whole?
I am fortunate enough to have unlimited interwebs through my DSL ISP, and I occasionally have guests that come by who would like to use it on their mobile devices.My problem is that when my Guest Zone is enabled there is no internet access. Otherwise the Zone functions 'normally' devices within the zone can view each other, but not outside.It is important for me that the Guest Zone doesn't see any of the devices within my Host Zone.
DIR-655 - Rev B 2.03NA
Connection: PPoE
Reconnect mode: On Demand
Wireless Mode: Mixed G/N
I'm looking for a way to connect to my neighbors wireless connection... I have been using it for a while and then he hid his SSID and now, his connection is listed as an Other Network.I found out his MAC address, but I'm wandering is there a way to connect to the wireless network or just to find out that hidden SSID?
View 1 Replies View RelatedI want to search hidden ssid names means non broadcast ssid.
View 2 Replies View RelatedWe have three Access Points, two Cisco Aironet 1260 and one 1240AG. Originally, the SSID was hidden on all three AP's and users had to go to Other Networks and type in the SSID and password to access the WAN. About a few months ago, the network started broadcasting to the public. I am trying to make the SSID hidden again. I have tried going to the Security tab, choosing the SSID Manager and setting single guest mode to none but it has not worked.
View 4 Replies View RelatedI have found that if I do not enable the broadcast SSID option on my 5GHz N network that my devices will forget the network and not reconnect on their own. Yet, I have the 2.4GHz G/N network set up to not broadcast my SSID and I have no problems. Why can't I disable my SSID broadcast on the 5GHz N network without these problems?
View 9 Replies View Relatedhow i can have internet connection again. here's what happened, i disabled the Broadcasting SSID and the after that my devices can no longer locate the wifi, and then when i cant configure the setting back to its original settings because i cannot establish a connection with the mf30 and my laptop eventhough it's via USB.
View 1 Replies View Relatedwhy my SSID still displays even though I have the SSID Broadcast "Disabled" for 5 GHz and 2.4Ghz configurations. The name of my network shows full signal strength and a lock next to the name but I was under the impression if I have disabled the SSID broadcast it shouldn't show up at all and would force a user to manually input the network name when trying to connect to it. I have the router configured to only allow certain MAC addresses wireless access as well. Router is running Firmware Version: 1.0.03.Also, my primary computer my iMac running 10.7.2 boots up or is brought out of sleep mode I constantly need to go up to the top of my screen and re-select my network.
View 4 Replies View RelatedIs it possible to connect the dap-1622 to a hidden network using WPA Radius? I've tried, but didn't succeed. I'm running FW version 1.41. I've tried with older FW versions, and none of them seems to work.
View 1 Replies View RelatedAs seen from the pic below, I have DIR-655 with hardware revision B1 and firmware version 2.0. The printed, online, and in router manual says that there should be ALG section at the bottom, but as you can see there is nothing there. Is there any setting that makes the ALG section hidden?
View 4 Replies View RelatedI have a Cisco 2901 which terminates a Class C address pool. I have split the Class C address pool into 3 sub-nets and 2 zones and created a non-addressable pool (private pool):
dmz-zone : x.x.x.0 TO x.x.x.127 (x.x.x.0/25)
in-zone: x.x.x.128 TO x.x.x.159 (x.x.x.128/27) & x.x.x.160 TO x.x.x.191 (x.x.x.160/27)
private-zone: 192.168.x.0 TO 192.168.x.255 (192.168.x.0/24)
I have configured private-zone NAT to use address pool x.x.x.161 TO x.x.x.189 within the in-zone.
Within the:
dmz-zone - are servers for : DNS, Syslog, SIP & HTTP/HTTPS in-zone - is a SMTP mail server which is behind VPN Gateway/NAT, TomCat (Application Server) and PostgreSQL Server private-zone - is where all standard users are operating from and they can access the SIP & HTTP/HTTPS servers within dmz-zone My problem is that I cannot seem to configure the ZBFW to allow the dmz-zone HTTP/HTTP server to redirect to in-zone TomCat server.
I do not want to make the TomCat server generally visible and am instead using the Apache proxy/ajp13 to connect from dmz-zone server to in-zone server.However I cannot seem to get anything (including icmp) to work from dmz-zone to in-zone.
I have Policy:
POLICY-DMZ-IN (dmz-zone to in-zone) which has:
any any udp/tcp inspect
any any icmp inspect
unmatched traffic DROP/LOG
But I still cannot get anything from dmz-zone to in-zone...Could the POLICY-DMZ-IN be being overridden by other dmz-zone to out-zone policies?
NOTE: I have routing rules for each of various sub-nets and all out-zone to dmz-zone, out-zone to in-zone and private-zone to out-zone, in-zone and dmz-zone routing works ok, so it appears problem is with ZBFW not routing table.
how to setup a separate SSID for guests (without a password).
Basically, we have one SSID now called Mnet which has a WPA2 password. For guests coming in i want Mnet Guests where people can connect without needing a password. They should be able to use internet but not connect to LAN devices, how to accomplish this with this WAP321?
I am trying to set up a guest SSID which will be separate from other corp SSIDs. I have read about this auto-anchor feature and I have a basic idea. Here are some questions about the network design
1. Can Cisco 5508 with 7.2.111.3 code do NAT? I mean can I use the anchor controller also as a gateway to Internet or do I need another device such as FW or router to do the job?
2. I want the guests to get IP address in 192.168.0.0/24 range. On the anchor controller I will need an interface in this range, correct? However on the internal controller I won't need this interface. The guest ssid will be associated with the management interface on the internal controller, correct?
3. I want the guests to get IP address from general DHCP server. Does DHCP request have to come out of the new interface in the 192.168.0.0/24 range? However this interface will be connecting with the FW. It won't have connection back to the internal network to reach the DHCP server. The management interface will have the route to the DHCP server. Is it possible to use management interface for this SSID but still let traffic to pass through the Guest interface?
I am setting up a guest WLAN network on our existing 1242 AP's using a seperate VLAN. On most wireless devices which are on the company network/VLAN's, I have used WEP authentication with hex keys, and no broadcast. Obviously this cannot be the same for a guest internet connection.We want to have the VLAN/SSID in guest mode (which i have configured) for broadcasting, and then once someone selects the SSID on their laptop or smart phone, they are just prompted to authenticate with a standard alphanumeric password (example "guestwifi") instead of a 40 or 128 bit key.
I have searched all over and tried multiple things in the CLI on AP1, but can't seem to get anywhere.
I have a cisco 877 configured foir lan to lan between sites A and B. I have used vlan 1 but looks like i have to bvi1 if i need to use the wireless,what is the difference between bvi and vlan. if i wanted users on the same vlan and wireless what would be the base config ? at the moment all corporate traffic goes to site A and other traffic goes to internet. now would i be able to create two ssid, one for corporate to access corporate subnets and the other for guest access alone where the traffic goes out to the internet.
View 1 Replies View RelatedI have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies View Relatedi have two 5508 ver 7.3.0, one is the primary and one is the guest controller. mobility is up and running. i have an exising guest ssid working with wpa2-psk and web authentication and its working fine but i require a second guest ssid that only uses a wpa2-psk for ipod/ipads as i cant use passive client on primary controller. i presently have the one vlan range and dhcp setup on the guest controller to give addressing to either ssid. i know you can have multiple ssid setup on the guest controller but in other sites i have only had one guest connection comming from the primary controller, just a primary controller on each sites was only creating one link to the same guest controler.
View 3 Replies View RelatedMy customer need creates some separately web portal for some SSID (Guest and Staff), 01 web portal for Guest and 01 Web portal for Staff. Can WLC2504 can support this features ?
View 2 Replies View RelatedConfig:
Netgear ProSafe Gigabit Router is my DHCP Server -- The entire home net work is on the same subnet (192.168.15.xxx)
Linksys E4200 configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
Linksys WRT610N configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
3 -- 5 port gigabit switches
1 -- 8 port gigabit switch
No more than two switches between any two wired devices Both Linksys access points have the same SSID and WPA2 security phrase -- total of 4 radios Nonoverlapping channels are selected on both the 2.4Ghz and 5.0Ghz radio to minimize interference All computers are running Windows 7 Professional 64bit with all the latest updates Two iPhones and one iPad also access the network All LAN and WAN connectivity is working as designed?
Problem:
guest SSID is turned on
password is established
All devices will connect to the guest SSID and the E4200 is assigning an ip address to the device in the 192.168.33.xxx range which is what it's supposed to do.When I open a web browser, I am not automatically redirected to the Cisco Login Page. If I enter 192.168.33.1 as the URL, the login screen is presented. I enter the password I have created in the guest admin page on the wireless guest tab. I then see a blank page and a URL of 192.168.33.1/guestnetwork.asp. THIS IS WHERE I GET STUCK. THE ONLY WAY TO EVER SEE THE LOGIN PAGE AGAIN IS TO REBOOT THE E4200, otherwise you just get unable to connect messages when opening web browsers and the wireless status icon in the system tray shows a yellow exclamation mark.
I successfully connect to the guest SSID but I do not get access to the internet. When I type ipconfig, I see that the DNS is set to 192.168.33.1 which does not exist on my network. I assume there's some internal NAT magic that is supposed to happen in the E4200 to bridge me over to my 192.168.15.xxx network but it doesn't seem to be happening.At the beginning of the call I specifically asked them if the E4200 must be the DHCP server in order for the guest SSID feature to work and they said no. 1.5 hours later they had no answers so they told me that it wasn't working because the E4200 was not the DHCP server. The documentation says nothing about a DHCP requirement for guest AP service. Linksys support further could not answer what you would do if you needed more than one AP with guest service enabled.It seems like this is a firmware issue but it may be the guest SSID service requires the E4200 to also act as the DHCP server. Whether this is a bug or if the router/AP is working as designed?
A query here with regards to Wireless isolation between SSID and wireless isolation within SSID.If we have 2 SSID, eg. InternalSSID, GuestSSID on AP1.Both SSID are set to Enabled for isolation between SSID, and within SSID, that would mean all machines connected thro' this AP1, would be isolated from one another.
1) If there's 1 laptop that connects to another AP, lets call it AP2, (doesn't have isolation function) on ssid01. Would this laptop still be isolated from those that connects to the first AP?
2) If there are wired PCs connected to the router. And the 2 APs are connected to the same router. Would the machines connected thro' the AP1 on either InternalSSID, GuestSSID be able to access those wired PCs? (My assumption is yes.)
3) Is there a quick and efficient way to setup on WRVS4400N to isolate GuestSSID totally from InternalSSID, and wired PCs. InternalSSID and wired PCs should be allowed to 'see' one another.
The challenge here is that, the network points are all installed already. Both AP are connecting thro' 2 separate unmanaged switch together with a couple of other PCs. 1 Port on the unmanaged switch, each,connects to the router.
We are deploying 3600 AP's with a 2504 and would like to create multiple SSID's that are mapped to unique VLANs so we can control the traffic at the Firewall. We have the 2504 up and running with AP's but there appears to be no where in the 2504 controller Web GUI to configure a VLAN mapping to an SSID. Any pointers to documentation on how to configure?
View 1 Replies View Relatedi have a e3000 set up with my network i have guest network set up through the cisco connect but dont see a field to change the guest network broadcast ssid so an ideas?
View 1 Replies View RelatedWe have been deploying 3502 APs remotely to locations with full T1s that backhaul to where I sit at HQ. Both the foreign and anchor controller are here at my location.
I am seeking to rate limit per user the bandwidth each client will get on the guest internet ssid. As you know this traffic is encapsulated in capwap between the AP and the controller so I cant use a standard ACL on the switch or router.
We are trying to keep the guest internet access usage in check on the T1 at any given site so the other ssid's & local lan traffic is not overly competing for the bandwidth.
I found the place to edit the default profiles in the controller but the documentation really isnt clear on best practices.
So I put it to you my fellow wireless engineers to suggest how you are implementing bandwidth management on your wireless guest internet.
Oh and here is my hardware & software levels.
5508wlc - forgeign
4402wlc - anchor
Software Version7.0.230.0
I'm trying to find a document in Design Zone about configuring a Wireless AP and I wasn't able to find it. I have a good experience configuring switches, routers and firewalls in CLI and this is the first that I have my hands on APs (1240 AG).
View 2 Replies View RelatedI have set up a zone-based policy firewall with HA on two 2911 routers as per the Cisco security configuration guide, for an active/passive LAN-LAN cluster. All works as expected, but there is one problem I find: when the control link between the two devices fails, they go into an active/active state as each member assumes it's the last surviving member. The ARP entries for the Virtual IPs on the neighboring devices point to the device that last claimed the active role (usually the standby device). This works in a way, just sessions don't get synched anymore (control link is the same as data link). Now when the link comes back up, the preemtion works and the active, former standby device goes back to standby. But the ARP entries on the neighboring devices still point to the standby device and nothing goes (also sessions established during the active/active state are lost due to resync with the now active member).
This is a single point of failure and what I need is a way to mitigate that. Under:
redundancy
application redundancy
group 1
control <interface> protocol 1
only one control interface is allowed. Other manufacturers with similar functionality provide for the possibilty of a backup control link, for example the internal LAN interface or a dedicated backup link.
How would I go about that? Maybe use a port-channel for the control/data link (but I'm out of interfaces)?