What would be the best option to monitor the load on AP live? Is there a GUI tool for this or should I use command line interface? I was hoping that CNA would do this, but the AIR-SAP1602I.EK9 does not seem to be supported by the CNA. CCP seems to be another application, would this do what I want?
View 1 RepliesI am aware there is a feature request but don't see any updates. Taking the chance here that its fallen through the cracks and someone has figured out another way to monitor inspection load on ASA-SSM-20 IPS. We are currently running 7.0(5a)E4. I want to be able to use Solarwinds Orion to monitor Inspection Load on our IPS devices.
View 1 Replies View RelatedI was looking in the CISCO webpage how to load an IOS from a tftp server but i got some questions:
I got the information from this webpage: [URL]
rommon #1> ADDRESS=10.132.44.177 <---- Which IP address? the one that I got on my firewall?
On a 1602 autonomous AP in the US, should the maximum DB power level be 22DB or 17DB? According to the datasheet it shows 22DB when all 3 antennaes are in use although I am only showing 17DB as the allowed maximum even though all 3 are enabled.
Antenna: Rx[a b c ]
Tx[a b c ofdm all]
Internal
Gain [Allowed 8, Reported 0, Configured 0, In Use 8] (dBi x 2)
[Code]....
I have successfully setup the Cisco 2504 (AIR-CT2504-K9).
Trying to add 2 Access Points (AIR-SAP1602I-A-K9). I created static IPs for both in the router (RV180). The Access Points are connected to the PoE ports on the Cisco Switch (SG200-08P). The 2504 is connect to one of the non-PoE ports on the SG200. The SG200 is then connected to another switch (SF302-8P), which is connected to the Router (RV180), which is connected to the cable modem (Cisco DCM3000).
I am able to ping both of the access points from within the LAN, but they do not show-up on the 2504 console.
AIR-SAP1602I is a Standalone AP (Fat-AP), can we convert it to Ctrlr-based AP(Thin-AP) via install another IOS ?!In contrast, can we convert AIR-CAP1602I to be a Standalone AP ?!
View 5 Replies View RelatedI am trying to have a setup where the AP running in autonomous mode also act dhcp server for the wireless clients.The only thing is that the vlan is switched across to the wired network.
So basically i am having 2 vlans, one for mgmt and other for data (for wireless clients) and both vlans are trunked to the switch.
[CODE]...
I want to buy an AIR-SAP1602I-E-K9 and I don't know if I can configure a MAC-BASED ACL with this AP, because I must permit the access of the wireless netwok only to determined wireless devices.
View 4 Replies View RelatedI have a wireless router, a wirelessly connected smart tv, and a wirelessly connected laptop. Can I use my tv as a wireless monitor?
View 1 Replies View Relatedwe have purchased a couple of new Aironet APs for our office:
AIR-AP1262N-E-K9
My objective is to use some of these as wireless monitors to scan the vicinity and to report the SSIDs and RSSI values of all detected APs.
Basically something similar to the Linux command: "iwlist wlan0 scan".
Periodically, I would like to transmit the scanning results to a central server (e.g. via SNMP) for monitoring the whole network area.
Are there built-in commands in the IOS to do this? Or can I use Tcl scripts to perform this task?
I have worked with Cisco routers and switches before but I am new to wireless devices.
i need to monitor the traffic on a multi users wireless route
View 8 Replies View RelatedI have installed an SR520 with wireless for a client. They have asked if there is an easy way for them to monitor who is connected to the wireless at any given point in time. They are not capable of using the IOS command line.
View 1 Replies View RelatedI'm looking for a way to monitor client authentication failures with our 3 standalone 1142N APs. I know that I can see failures under the log viewer of each AP
View 4 Replies View RelatedI recently received an email from my internet provider showing illegal movie downloads through my modem. I have a wireless router hooked up (with password security) for my roommates to use and would like to monitor their internet activities to know who is downloading these movies.
View 3 Replies View Relatedwe have a high speed internet and my modem is capable of wireless what I want to know, is there a way that I can monitor how much my daughter is on her computer and what websites she is visiting without having to install a program on her notebook or having to check her history etc? I would like to be able to do it all from my computer
View 2 Replies View RelatedI've been having some problems with the Monitor Clients menu on a WCS 7.0 server, for instance if I go there and display the detected clients on the last 24 hours I get a different set of clients than if I go and generate a report of unique clients for the last day on the report menu. Is this normal?, shouldn't both reports get the data from the same place and give the same result?.
View 4 Replies View RelatedI have a cable modem with a wireless router attached.There are 2 laptops that connect to the internet via the router. I've never been able to get the hard wired desktop to connect to the internet via the router, so, when the desktop is used, the router is disconnected from the modem and the desktop is connected.I do not have free access to the modem, router or desktop devices, but I do have free access to the 2 laptops.I would like to be able to install on one of the laptops, something that would keep track of the internet connectivity.
I know that even when the router is disconnected from the modem, it is still sending it's wireless signal (most likely) but it's not connected to the internet anymore.So, I would like to be able to know the date and time the router looses internet connectivity and the date and time it gets the connectivity back every time this happens.I would love to be able to monitor the activity that takes place on the internet during that time frame, but know it's not possible when all I have access to is a wirelessly connected laptop that would lose the internet connectivity. So, it would be good just to be able to know when the router is disconnected and how long it is disconnected.
How can I monitor broadband usage of multiple PC's connected to a wireless router/modem?
View 1 Replies View RelatedHow can you see who is connected to your router network? I am using a Linksys E2000.
View 1 Replies View RelatedHave a PC set up with a LINKSYS N2500 router. this is password protected for access to network I would like to monitor what one of my children is doing on the net - but they surf the net using an iPad
View 4 Replies View RelatedMy Belkin N150 wireless router monitor has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you us a solution is available.I can not figure out why my wireless router doesn't work sometimes.I need to be able to access this to get to the router settings. I don't know if my wireless is being highjacked or what.
View 2 Replies View RelatedIs there a way I can monitor what web sites are visited through my E4200 V1 (firmware v1.0.04)
View 3 Replies View RelatedI've got the E3000 set up and working. What I'd like to do now is monitor all the devices' connectivity to it. The bandwidth it consumes and stuff. Is there a way to do that on my router?
View 6 Replies View RelatedAll my previous routers have allowed me to monitor my connection speeds however I can't find this in this router. I found the client table under "status" but I have not been able to find the connection speeds anywhere. I like to make sure that my devices are running at close to 300Mbps and not 54Mbps in case I have a connection setup wrong. I have searched in the forums without much luck.
View 9 Replies View RelatedI just got optical fiber installed in my place which gives me great download speeds. Now my ISP has a monthly download limit of 120GB, after that I gotta pay overages.Now my setup is like this: Fiber modem (1 port) -> Linksys E3000 router (4 ports + wifi).All my gear is hooked up to the Linksys router (xbox, ps3, media center, office pc & 2 laptops).I would like to keep track of the total "internet" bandwidth use of all devices, but exclude the normal network traffic, as that of course I don't pay for.Is there something that I can install on the Linksys router that can keep track of that kinda of information? router (4 ports + wifi).
View 6 Replies View RelatedI have a WRT160N router. Are there any network software packages out "there" than will allow me to track the total traffic on this device?
View 1 Replies View RelatedI successfully installed the AirLink101 AWLL6075 Adapter, however it cannot find networks because the Wireless Monitor section is always checked as being "Disabled". When I uncheck the box, a few seconds later it comes right back to Disabled with the check mark again.
View 14 Replies View RelatedI am looking to track what my kids are doing on the internet. I have an ea4500 and was wondering if there is a detailed log file that I can look at?
View 3 Replies View RelatedI use a WPC54G wireless adaptor to connect a laptop to my home network. I just replaced a WRT54G2 router with a Cisco Valet router.When I start up the laptop, the wireless adaptor's Monitor configuration takes priority over Windows XP wireless configuration, but the Cisco Valet does not recognize the Monitor. If I disable the Monitor, everything is fine until I reboot, and then the Monitor again prevents connecting to the router.
How do I permanently disable the Monitor software so that the laptop will default to the Windows XP wireless configuration settings?
The "Wireless Network Monitor" for my Linksys Dual-Band Wireless A+G Notebook Adapter Model No WPC55AG has been unable to run after I last updated my Windows XP machine using Windows Update. The problem presents itself immediately upon login (because the monitor is set to run on startup) with an error window that says "Abnormal program termination" and "WPC55AGV2.exe" in the title bar. I suspect the problem occurred because one of the new updates included an upgrade to the Microsoft .NET Framework Services 3.0.
View 6 Replies View RelatedI am sharign my bandwidth with my neighbour and would like to keep a tab on what he is downloading, and then limit the speeds he gets while using my 4Mbps line. He's accessign using a WIFI L:AN card.Can I do this usign WRT160Nv2? Maybe any third-party.
View 2 Replies View RelatedI have three of these AP that quit associating with the controller after a power loss. I have dismounted one of them and it has an Amber light on ethernet LED and Green Light on radio LED and off on status.It does not respond to reset and nothing happen when i console into it. What might have happened to this AP? It's barely two years. I have tried different power injectors and direct power and still behaves the same way.
View 3 Replies View RelatedIs it possible to enable load balancing for a particular group of APs and disabled for the rest. Perhaps AP groups. Running 8500 WLC with 3600 series APs. It will enhance the service concurrent user capacities for areas with a high device count.
View 4 Replies View Related