All my previous routers have allowed me to monitor my connection speeds however I can't find this in this router. I found the client table under "status" but I have not been able to find the connection speeds anywhere. I like to make sure that my devices are running at close to 300Mbps and not 54Mbps in case I have a connection setup wrong. I have searched in the forums without much luck.
View 9 RepliesI just got an e4200 and I'm haviong very disappointing wireless speeds. My network is setup as follows
powerline----------desktop
|
|
powerline-----------wireless router ----------- laptop (using USB adapter Linksys AES1000, Intel bng internal, Belkin adapter)
If I plug into the back of the e4200 I can download at roughly the raw speed of the powerline 7 MBps. So I know the powerline connection is just fine and the routing function of the e4200 is just fine. When I use my laptop my speeds are wildly variable on both 2.4 and 5 ghz. With a clear line of sight to the router (maybe 7 feet away) they seem to hover around 1.5 MBps but have reached as high as 5.5 MBps twice. Using my much cheap older Buffalo router I routinely get speeds in the 4.5 MBps range which I would consider acceptable (although it has other, separate issues). I have followed all of the advice I can find on the forums. The range is also pretty terrible. If I'm 20 feet away and no longer have a clear line of site to the router I will frequenly have almost no signal and miserably slow download speeds in the kbps.I have made sure that I am using wpa2 with AES, I have changed my MTU to 1365, I have updated the firmware to the one released in March, and I have explored setting different channels on the router to no avail. I also contacted tech support which I'm only marginally sure understood that I was talking about the LAN connection and not the internet.
Is there a way I can monitor what web sites are visited through my E4200 V1 (firmware v1.0.04)
View 3 Replies View RelatedUsing 1.0.03.
I am seeing something pretty bizarre: when trying to copy files between two computers (both Windows 7 SP1 64bit), both physically plugged into the back of the E4200, I see extremely slow transfer speeds: 1.0-1.1 MB/sec. Both computers are fast (i7-2600K, both using SSDs) and both have gigabit ports (and the 4200's web UI shows both ports in question as operating in gigabit mode).
This is so slow as to be sort of funny. Each of these computers see speeds well in excess of that when transferring between the computer and outside internet sites...so it's kind of funny that two computers plugged into the same switch in the back of the 4200 see 1 MB/second.
All I want is functional Wi-Fi in my house like the rest of the world. Unfortunately, I cannot have that for whatever reason.
Now that I said that, Let's me get down to explaining my issue. I orginally owned a Linksys WRT350n. This router worked fine for years, untill one day I decided to do a speed test on my new Motrola Atrix. My Wired computer gets ~22000kbps down and 4000kbps up... My wireless speedtest on my Atrix yielded 2000kbps down and 4000kbps up. I assumed it was the phone, so i went and tried every other wireless device in my house. Everyone of them got the same result.. 2000kbps down.. 4000kbps up.
At this point I went into my router settings and tried every available channel, all of them yielded the same result of 2000kbps down and 4000kbps up.. At this point, I assumed it was the router. Ive had it for a few years and figured it was just reaching EOL. I rushed to my nearest bestbuy to pick up a brand new Linksys E4200. I brought it home, hooked it up and was eager to test my new wireless speeds. Unfortunately the same results of 2000kbps down and 4000kbps up was the yield. Once again, I've tried every possible channel with no change to my speeds. At this point I called up Linksys/Cisco support.. They were POSITIVE it was a hardware issue and had me exchange the router, even though I informed them i had the same issue with my older router of a different model. I went along with it anyway, and exchanged my router. Same issue. I called Cisco/Linksys back up and informed them, and basically they told me "they'd make a note of the issue and call me back at a later date."
I downloaded a WiFi Analyzer on my cell phone. Theres only two other dectable networks in my area, and they are low low low signal. So, I don't believe it's heavy saturation. The router is in the same room as 3 of the wireless devices that get 2000kbps down/4000kbps up. So it's not range either.
I just bought a new Linksys E4200, and connected it about an hour ago. I have a 30Mbps internet connection when connected direct to the modem, but when connected wired to the router, max speeds are 8Mbps.
View 2 Replies View RelatedI just upgrade my service with Comcast so I can now get up to 50Mbps, however the modem when directly connected to the PC can obtain these speeds, it does not when the PC is connected to the E4200 router. In fact the Cisco Connect speed test shows the upload speeds (10+ Mbps) to be faster than the download speed(4.82 Mbps). I upgraded the firmware to the latest level but it did not make a difference.
View 4 Replies View RelatedSo I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View RelatedI'm having a problem where my connection speeds slow down on my iOS devices. I have a EA2700 router. I have PC hard wired into the router, which maintains steady speed test numbers when other devices slow down.i have another pc that connects wirelessly (2.4 only) that maintained speed white the other devices slowEd down. Both my iphone5 and new iPad would slow down. The quick fix wasto turn the wifi on the device off, then the speed would return when reconnected. Also clicking "renew lease" in the iPhone wireless settings seemed to correct the issue.I'm not sure if there is a setting on the iOS devices or the router I can change to stop this.
View 3 Replies View RelatedMy dad recently got a E4200 router, My whole family are mac users, the connection are all okay with their computers, I'm the only one using Microsoft, ASUS running on Vista. The connection is fine when I'm near the router, but when I go to my room I get no connection at all, it connects for a second but then it goes on connection with limited access.
View 5 Replies View RelatedLast week I bought the E4200 thinking it was probably the best router on the market and if it worked properly, it would be...I think.I have attached a Seagate GoFlex Desk 2Tb USB drive formatted to NTFS to the USB of the E4200. I can map to it from my Windows XP computer with no problem and I can FTP to it from any browser...my Windows 7 machine is another story. When I try to map the network drive from the Windows 7 machine I get error code 0x80070035 every time. I've seen some other threads where people are having this problem but in the cases I've found, they aren't getting any connection via XP or FTP either.
View 2 Replies View RelatedI have just installed Cisco Connect v1.4 (11266.0), and have upgraded my E4200 software to 1.0.03.I want to add a USB printer connected to the router but when I open Cisco Connect, and select the "Add new devices.....' button, the only option for a printer is 'Wireless Printer' not 'Printer' followed by USB or Wireless as per the User guide.
View 9 Replies View RelatedI have been using a Linksys E3000 router for a few months now. Love it. But this last week, when ever I wake my monitor up after it's power saving mode kicks in, I lose my internet connection for about 15 seconds. If you look at the router before the monitor is on, I am connected. The light is on for port 1. But as soon as my monitor gets turned back on, it light just turns off and will reconnect after about 15 seconds. I've looked it up online and can only find things about when the entire system wakes up, and usually those people have to reboot their entire system to get a connection again, or turn the router off then back on. Using Windows 7?
View 4 Replies View RelatedI have an E4200 (v1) with the latest firmware. For some reason, the E4200 does not allow me to conenct to certain websites. This is true for wired or wireless connections.To test, I connected a wired PC directly to my cable modem and was able to connect to all websites fine. I also tried an old D-Link router I had on hand and was able to connect to all sites fine. Went back to the E4200 and was blocked. I re-loaded the firmware and same results.
View 4 Replies View RelatedI have my e4200 connected to another modem/router (2Wire 3600HGV), because the other router does not support Wireless N. I can connect to my E4200 network, but there's just no connection to the internet. I reseted my e4200 but still no luck. I've unplugged both routers and replugged them, nothing. I know it's possible because I've had it set up before but I had my 2Wire exchanged for a newer one.
Firmware: 1.00.4
Just to be sure. I have the cable going from my modem out of port #1 and into my e4200 where it says internet, thats correct, right? On my e4200 i have the IP 192.168.1.2 but on the 2Wire I have the e4200 as 1.92.168.1.66.
The web site says that the E4200 has a USB port to connect USB drives and printers. That sounded to me like multiple devices could be added. It says nothing about only being able to connect one. Since I have 3 USB drives and 2 USB printers, that sounded great. Setting it up, it seems that this port will not use a HUB, and can only be used for one USB device. How can that be? That is so limiting as to be nearly useless.
View 3 Replies View RelatedI have an E4200 v1 wireless router. Intermittently, my hard wired laptop (and hard wired desktop) loose Internet connnectivity and when I look at the 4200 I see the status light flashing slowly like it was just rebooted. I am runnong 1.0.04, have reset to factory, reflashed the 1.0.04 code and done a 30-30-30 reset (so far no drops since the 30-30-30 reset but we'll see).
View 9 Replies View RelatedThe problem: running a standard single band 2.4gz BT homehub. When using my xbox and wireless headset (razer chimeara) the xbox loses connection. When i tuen the headset off i no longer lose connection. This suggests to me that the headset is simply emitting on the same frequency and bullying the connection, thus the xbox disconnects I have purchased the wireless N adapter to allow the xbox to run on the 2.4 or 5ghz band. I am now looking for a duel band router to allow my xbox to connect to the 5gz band and hopefully this will rectify my interference issue with the headset. I have been lookijg at the e4200 as this supports seperate ssid for 2.4 and 5ghz band, so the xbox can run on the 5ghz and the intererence from the 2.4ghz headset should subside - do you think this would work? Also, with the single ssid duel band routers, where 2.4/5gjz share the same ssid - how would my wireless N devices know to run on the 5ghz and not the 2.4?
View 3 Replies View RelatedI have a E4200 V1 with firmware 1.0.0.5 installed The problem is that when I connect the cable from my modem to my router and recycle both I get a rapidly fashing Cisco light and can not connect to the internet.If I remove that cable and recycle the router my network works but (obviously) I have no internet connectivity.This was working (almost 2 years) without issue until today.I updated the firmware and did a factory reset and neither resolved the issue.My next experiment is to see if I can't get log files (since the factory reset) but I can't do that at this time.
View 3 Replies View RelatedI bought a e4200 router about 3 weeks ago and after a power outage it decided it didnt like being connected to the internet anymore. So i got on the phone with cisco they determined the router was no good, mind you my laptop would connect wired. So they sent me a "refurbished" one, so i set it up. The new setup was wonky because it said the same message "Your connected to your router but..." then after trying to get the connection its self and failing it came up with "congratulations you are now connected to the internet". That lasted 3hrs and 45mins then died, so i went upstairs to power cycle it, it decided to connect with the old settings. That lased 25mins then died, so i reset it and reconfigured the router. Wouldnt connect, i checked my mac address and it was using my wireless one and kept turning on my wireless connection durring the install. So i cloned my wired mac address and got the internet for roughly an hour... then it died. So i reset it again and kept the wifi off got it going and decided to go to sleep. I wake up and its still working after 8hrs, i go down stairs with my tablet and i dies again. This time it refuses to reconnect, refuses to reset back up just doesnt want to work.
View 3 Replies View RelatedI just purchased e4200 from a friend of mine. Got an issue with setup of this device. I use a model from internet provider. Have 2 computers at home. One is pc with cable, another one mac with wireless.SO my issue is that i can not connect none of them. I was trying to use cd that comes with router but he can not locate a router. When I connect cable directly from modem to computer everything works fine. As soon I connect cable to a router I can not see a router and I can not connect to internet.
View 1 Replies View RelatedThe latest Firmware for the E4200 states that there is now the ability to attach a printer to the USB port of the router. I am using a Mac, so that may be the problem, but I have followed the instructions on how to add the printer and it is not happening. It's possible that the MAC Firmware was not given the ability to add a USB printer like the PC Firmware upgrade.
View 9 Replies View RelatedI just got an E4200 and have a SBG6580 cable modem. I cant seem to set this up properly and my connection keeps dropping. What is the proper set up ? I would like to configure it so the cable modem handles the DNS and the E4200 handles the wireless.
View 4 Replies View RelatedI have the latest version firmware
I am constantly getting dropped and timeouts accross all of my devices this has been hapening for several months now I think ever since I upgraded to 1.0.04
It says no internet access when the wired computers have it fine. Android phones, windows 7 pc, and chromebook.
I installed the E4200. Internet works fine, and the internet connection is maximum performance. But if I copy a file between laptops, or to my mediaplayer (AC Ryan HD2), the connection is 3MB/s tops. I changed to the 5gHz and N settings, still no change.
View 6 Replies View RelatedWhen I try to connect OpenVPN through an E4200 v2 router from my Linux Fedora 16 client, the connection hangs. The connection log show that OpenVPN has connected to the VPN server. Internet also freezes until I disconnect OpenVPN.
OpenVPN on Windows works fine through the E4200 router.If I connect the Linux client directly to my Inteno fiber router, OpenVPN works fine.Passthrough is enabled in the router, and I have configured QoS and port forwarding for port 1194. The router has firmware version 2.0.37.
Bought an E4200 to replace my Netwgear router and am experiencing the following problem.One of my wireless boxes serves as mu mail server. I've been running this configuration for years so the only thing that has changed is the router.The neworkd is up and all wireless clients can connect, but after some time, access to the mail server just 'freezes'. I say freezes as the nework icon (i'm using ubuntu' still show a connection. In addtion, there are not error in any of the logs. I just seems that the mail server and the router just stopped communication.
View 9 Replies View Relatedever since i had a power failure losing all power in my apartment, my router has begun regularily losing connection to the internet, I have to go into the router and renew ip address which is quite annoying
[code]....
So I recently purchased an E4200 to replace my aging and slightly ailing DLink DIR-655 which as served me well for going on 5 years. The part of the DLink that was giving me the issues was the wireless, the routing and switching worked fine however.
I do quite a lot of streaming of media from my home machine outside my network through the internet. Most recently I've been using Kalemsoft Media Streamer on my HP Touchpad, however I've used Zumocast, Windows Live, Splashtop, and a few others. I havent yet tried my PPTP VPN through the router for an extended period of time to see if it reflects this issue as well though.
Since replacing my 655 with the E4200 I've started experiencing a timeout issue. It seems to be semi-consistant and only happens after time of unuse or extended use (I havent timed it yet to see if it always happens after the same amount of time though).
Basically what occurs is this:
I'll be watching some video or listening to audio streaming from my machine and after a period of time (usually a long period of time) it'll suddenly lose connection, requiring me to re-connect through the software, like the NAT translation is timing out or something.
How it USED to work is this: It'd basically work until I stopped streaming.
My setup:
AT&T Uverse set to DMZPlus aiming towards my E4200 WAN port (sitting directly in place of the 655 I used to have)
All machines on the network are gigabit. I have ports 7000 and 7001 open for Kalemsoft Media Streamer on the E4200 per the specifications of the software.
The software understands UPnP so I have nothing specific forwarded on my machine, but I didnt previously either.
I have e4200 router and i notice sometimes when i am browsing that dops connection.
View 9 Replies View RelatedI purchased this router a few days after its release, and I was very impressed with its functions. I came from a DD-WRT flashed router with all the bells and whistles, and the E4200 lacked some features but I felt it was a fare trade off for the GHz & dual band.All was well with all my settings (quite a few to name QOS,forwarded, etc)I also updated the firmware when it came available and re entered same settings.
Approx 3 months after use I had 0 WAN connection via eth0 or WIFI, when I logged into router I was pulling a Public IP from my ISP. I could ping from inside the router but no connection on any hosts, very strange. Powercycling Modem/Router yielded same results.. I then backed up my vast amount of settings, and did a 30/30/30 reset.. With no configs I had no issue browsing on any host on my network. So I restored from backup and the issue was back again..So I did another 30/30/30 reset. Then went and reentered the exact same settings as before and the issue was gone.
I setup my E4200 v2 with different SSID's for 2.4 and 5GHz modes. I have no problem with a 2.4 Ghz connection on my laptop, but I cannot connect to the internet in 5GHz. mode. I choose the 5 GHz SSID and enter the passphrase but no luck, even though I have a full 4 bars inthe wireless icon.
View 4 Replies View Relatedmy e4200 wireless. I have internet connection speed of 40mb and I have epc 3925 working in bridged mode as modem and E4200 as router. When I connect my laptop with wire on e4200 I am getting 37-38 Mbps on speedtest.net which is perfectly fine. But on wireless I am having a lot of dropping of speed: I have 2mps then jumping to 5-6 Mbps and so on it never goes more than 5-6 Mbps. When I disable WMM Support in QoS I am having perfectly constant 20mbps but... I have only g network 54mbps. [code]
View 9 Replies View Related