Linksys Wireless Router :: E4200 Could Ping But No Connection On Any Hosts

Nov 28, 2011

I purchased this router a few days after its release, and I was very impressed with its functions. I came from a DD-WRT flashed router with all the bells and whistles, and the E4200 lacked some features but I felt it was a fare trade off for the GHz & dual band.All was well with all my settings (quite a few to name QOS,forwarded, etc)I also updated the firmware when it came available and re entered same settings.

 Approx 3 months after use I had 0 WAN connection via eth0 or WIFI, when I logged into router I  was pulling a Public IP from my ISP. I could ping from inside the router but no connection on any hosts, very strange. Powercycling Modem/Router yielded same results.. I then backed up my vast amount of settings, and did a 30/30/30 reset.. With no configs I had no issue browsing on any host on my network. So I restored from backup and the issue was back again..So I did another 30/30/30 reset. Then went and reentered the exact same settings as before and the issue was gone.

View 4 Replies


ADVERTISEMENT

Linksys Wireless Router :: E4200 - Unable To Ping Wifi Hosts From Lan

Nov 20, 2011

I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.

LAN - 192.9.209.0
WiFi - 172.16.1.0

Same config runs perfect on my WRTG54GL.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Unable To Ping Wifi Hosts From Lan

Jan 27, 2012

I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
 
LAN - 192.9.209.0
WiFi - 172.16.1.0
 
Same config runs perfect on my WRTG54GL.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Allow VPN Connection / No Traffic Passes Can't Ping Across Tunnel

Oct 28, 2011

I have recently purchased a E4200 i have flashed it with the latest Firmware 1.0.03 and Hard Reset the Router so the Media issue was resolved i was having. After upgrading the firmware to the latest version my Nortel VPN IPSEC Client no longer will work. The tunnel is connected and it passes traffic for about 15 seconds then nothing.  The connection remains connected but no traffic passes cant ping across tunnel.  I have checked all the settings and VPN - IPSEC - Passthru is enabled.   I have put the client in DMZ mode and tried that same thing.

View 7 Replies View Related

Linksys Wireless Router :: E4200 / Can't Ping WAN IP

Feb 2, 2012

I'm using Linksys E4200 router.  I can't seem to ping the static WAN IP (from internally or externally).  All other connectivity seems to be fine.  I can ping the routers internal IP, as well as the cable modem and other external IPs.  But all port forwarding through the E4200 is failing.Should the default security/firewall setting allow port forwarding?  Or do some settings need to change?

View 2 Replies View Related

Linksys Wireless Router :: E4200 Won't Update / Ping Or Trace Route

Jan 21, 2013

I have an E4200 and have added it to my network with a new static IP and DHCP and firewalls off.It runs off my cable modem and router (Virgin Media Superhub) that has DHCP.When I tell it to do a firmware update, traceroute or ping it fails, just wont do any of them.

View 9 Replies View Related

Linksys Wireless Router :: Can't Ping Windows Computers With New E4200 LAN / WLAN

Mar 18, 2012

just replaced a WRT54G with E4200. Most functions work well. 4 wireless computers (1 Macbook, 3 Win 7), 1 wireless android, 1 wired Win7 computer, 1 ethernet connected hard drive, 1 ethernet connected printer. All computers can ping router, access hard drive, access internet, ping android and ping Macbook.However, router, nor any computer, can't ping Win7 computers. Apparently IP based connections between WinX computers is blocked. My real applications are to Remote Desktop Connect from 1 Win7 computer to another, or to run a DLNA music server on 1 Win7 computer, accessed by another. (the LAN connected computer is the server, accessed by a wLAN client. All worked fine on WRT54G router, but can't connect thru E4200.  When these apps failed, I tried PING, and that failed as well.All computer's IP addresses are properly served from E4200 via DHCP, and are visible thru the router's DHCP Reservation panel.

View 1 Replies View Related

Linksys Wireless Router :: Start Ping Command Directly From E4200

Oct 9, 2011

I recently acquired an E4200 Linksys router.Is it possible to connect to it using telnet (from LAN)? For example I would like to start a ping command directly from the router.I tried to telnet using command line shell from Windows and it failed to connect on port 23.

View 4 Replies View Related

Linksys E4200 Wireless Router / Unable To Ping Machine On The Internet Side

May 7, 2012

I am using Linksys E4200 wireless router. I connected two machines, this way.

|LAP1|--------(LAN ethernet connection)----------|LinksysE4200|-------(Internet wired connection)--------|LAP2|

On the Linksys E4200, the Internet wired connection side, I gave static IP address which is in the same network range as that of LAP2.When tried to ping from LAP1 to LAP2, ping doesnot happen. Any settings by which I can ping from LAP1 to LAP2.

View 2 Replies View Related

Linksys Wireless Router :: E4200 Cannot Ping Addresses Of IPv6 Tunnel Ends

Nov 21, 2011

i have my Cisco E4200 set up with a 6rd tunnel. the tunnel seems to work fine for the most part. i can ping ipv6.google.com and get a response.however, i cannot ping the addresses of the IPv6 Tunnel ends from within my network. If i run a ping from outside the network, i can ping the IPv6 address of the server end, however, i cannot ping the E4200's end of the tunnel. is there a specific option that needs to be set? i have allowed ping so that my IPv4 address is pingable, am i missing something for IPv6?

View 7 Replies View Related

Linksys Wireless Router :: E4200 Ping To Router Very Unstable

Sep 8, 2011

I noticed some serious random ping spikes in online games and found that the connection between my Laptop and the E4200 is very very unstable. Sometimes it works perfectly fine but at other times my ping will spike each 5 seconds to three or even four digits and back to normal. I never get disconnected but playing is obviously not possible.
 
I ran several pingtests through pingtest.net and got everything from 15ms ping 3ms jitter to like 400 ping 300 jitter.
 
Eventually, I pinged the router (192.168.1.1) and got delays between 2ms and 300ms for both the 2.4 ghz and the 5ghz network. The 2.4ghz channels are fairly crowded but the signal is perfectly fine and stable. The 5ghz band is totally free therefore interference shouldn't be a problem i guess.

View 2 Replies View Related

Cisco Switching/Routing :: 1841 - Unable To Ping Remote Gateway Or Hosts On Other Side Of Router

May 30, 2012

I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
 
I am only using the FastEthernet interfaces on Router 1841.

View 3 Replies View Related

Linksys Wireless Router :: E4200 Get No Connection At All

Nov 22, 2011

My dad recently got a E4200 router, My whole family are mac users, the connection are all okay with their computers, I'm the only one using Microsoft, ASUS running on Vista. The connection is fine when I'm near the router, but when I go to my room I get no connection at all, it connects for a second but then it goes on connection with limited access.

View 5 Replies View Related

Linksys Wireless Router :: E4200 Not Getting Any Connection Via XP / FTP

Mar 21, 2012

Last week I bought the E4200 thinking it was probably the best router on the market and if it worked properly, it would be...I think.I have attached a Seagate GoFlex Desk 2Tb USB drive formatted to NTFS to the USB of the E4200. I can map to it from my Windows XP computer with no problem and I can FTP to it from any browser...my Windows 7 machine is another story. When I try to map the network drive from the Windows 7 machine I get error code 0x80070035 every time. I've seen some other threads where people are having this problem but in the cases I've found, they aren't getting any connection via XP or FTP either.

View 2 Replies View Related

Linksys Wireless Router :: E4200 - Connection Of V1.4 For Mac

Jan 29, 2012

I have just installed Cisco Connect v1.4 (11266.0), and have upgraded my E4200 software to 1.0.03.I want to add a USB printer connected to the router but when I open Cisco Connect, and select the "Add new devices.....' button, the only option for a printer is 'Wireless Printer' not 'Printer' followed by USB or Wireless as per the User guide.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Does Not Allow Connection To Certain Website?

Jan 2, 2013

I have an E4200 (v1) with the latest firmware.  For some reason, the E4200 does not allow me to conenct to certain websites.  This is true for wired or wireless connections.To test, I connected a wired PC directly to my cable modem and was able to connect to all websites fine.  I also tried an old D-Link router I had on hand and was able to connect to all sites fine.  Went back to the E4200 and was blocked.  I re-loaded the firmware and same results.

View 4 Replies View Related

Linksys Wireless Router :: E4200 - No Connection To Internet?

Apr 21, 2012

I have my e4200 connected to another modem/router (2Wire 3600HGV), because the other router does not support Wireless N. I can connect to my E4200 network, but there's just no connection to the internet. I reseted my e4200 but still no luck. I've unplugged both routers and replugged them, nothing. I know it's possible because I've had it set up before but I had my 2Wire exchanged for a newer one.
  
Firmware: 1.00.4
 
Just to be sure. I have the cable going from my modem out of port #1 and into my e4200 where it says internet, thats correct, right? On my e4200 i have the IP 192.168.1.2 but on the 2Wire I have the e4200 as 1.92.168.1.66. 

View 1 Replies View Related

Linksys Wireless Router :: E4200 - Way To Get USB Support For Connection

Nov 7, 2011

The web site says that the E4200 has a USB port to connect USB drives and printers.  That sounded to me like multiple devices could be added.  It says nothing about only being able to connect one.  Since I have 3 USB drives and 2 USB printers, that sounded great.   Setting it up, it seems that this port will not use a HUB, and can only be used for one USB device.  How can that be?  That is so limiting as to be nearly useless.

View 3 Replies View Related

Linksys Wireless Router :: WRVS4400N Can Get Any PING To Complete VPN Connection

Jan 14, 2012

I bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the QuickVPN Clien for connecting to my home network.My home network is connected to a pre provide by my ISP Thomson and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analysing the log you can see that I can get any PING to complete the VPN connection. [code]

View 1 Replies View Related

Linksys Wireless Router :: E4200 V1 Rebooting / Losing Connection?

Jul 5, 2012

I have an E4200 v1 wireless router.   Intermittently, my hard wired laptop (and hard wired desktop) loose Internet connnectivity and when I look at the 4200 I see the status light flashing slowly like it was just  rebooted.  I am runnong 1.0.04, have reset to factory, reflashed the 1.0.04 code and done a 30-30-30 reset (so far no drops since the 30-30-30 reset but we'll see). 

View 9 Replies View Related

Linksys Wireless Router :: E4200 - Xbox Lost Connection?

Dec 27, 2011

The problem: running a standard single band 2.4gz BT homehub. When using my xbox and wireless headset (razer chimeara) the xbox loses connection. When i tuen the headset off i no longer lose connection. This suggests to me that the headset is simply emitting on the same frequency and bullying the connection, thus the xbox disconnects I have purchased the wireless N adapter to allow the xbox to run on the 2.4 or 5ghz band. I am now looking for a duel band router to allow my xbox to connect to the 5gz band and hopefully this will rectify my interference issue with the headset. I have been lookijg at the e4200 as this supports seperate ssid for 2.4 and 5ghz band, so the xbox can run on the 5ghz and the intererence from the 2.4ghz headset should subside - do you think this would work? Also, with the single ssid duel band routers, where 2.4/5gjz share the same ssid - how would my wireless N devices know to run on the 5ghz and not the 2.4?

View 3 Replies View Related

Linksys Wireless Router :: How To Monitor Connection Speeds On E4200

Dec 28, 2011

All my previous routers have allowed me to monitor my connection speeds however I can't find this in this router.  I found the client table under "status" but I have not been able to find the connection speeds anywhere.  I like to make sure that my devices are running at close to 300Mbps and not 54Mbps in case I have a connection setup wrong.  I have searched in the forums without much luck.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Internet Connection Fails

Jan 1, 2013

I have a E4200 V1 with firmware 1.0.0.5 installed The problem is that when I connect the cable from my modem to my router and recycle both I get a rapidly fashing Cisco light and can not connect to the internet.If I remove that cable and recycle the router my network works but (obviously) I have no internet connectivity.This was working (almost 2 years) without issue until today.I updated the firmware and did a factory reset and neither resolved the issue.My next experiment is to see if I can't get log files (since the factory reset) but I can't do that at this time.

View 3 Replies View Related

Linksys Wireless Router :: E4200 Dropping Connection After Some Time

Nov 15, 2011

I bought a e4200 router about 3 weeks ago and after a power outage it decided it didnt like being connected to the internet anymore. So i got on the phone with cisco they determined the router was no good, mind you my laptop would connect wired. So they sent me a "refurbished" one, so i set it up. The new setup was wonky because it said the same message "Your connected to your router but..." then after trying to get the connection its self and failing it came up with "congratulations you are now connected to the internet". That lasted 3hrs and 45mins then died, so i went upstairs to power cycle it, it decided to connect with the old settings. That lased 25mins then died, so i reset it and reconfigured the router. Wouldnt connect, i checked my mac address and it was using my wireless one and kept turning on my wireless connection durring the install. So i cloned my wired mac address and got the internet for roughly an hour... then it died. So i reset it again and kept the wifi off got it going and decided to go to sleep. I wake up and its still working after 8hrs, i go down stairs with my tablet and i dies again. This time it refuses to reconnect, refuses to reset back up just doesnt want to work.

View 3 Replies View Related

Linksys Wireless Router :: Cannot Setup E4200 - No Internet Connection

Aug 9, 2011

I just purchased e4200 from a friend of mine. Got an issue with setup of this device. I use a model from internet provider. Have 2 computers at home. One is pc with cable, another one mac with wireless.SO my issue is that i can not connect none of them. I was trying to use cd that comes with router but he can not locate a router. When I connect cable directly from modem to computer everything works fine. As soon I connect cable to a router I can not see a router and I can not connect to internet.

View 1 Replies View Related

Linksys Wireless Router :: E4200 USB Printer Connection Not Working?

Jun 21, 2011

The latest Firmware for the E4200 states that there is now the ability to attach a printer to the USB port of the router. I am using a Mac, so that may be the problem,  but I have followed the instructions on how to add the printer and it is not happening. It's possible that the MAC Firmware was not given the ability to add a USB printer like the PC Firmware upgrade.

View 9 Replies View Related

Linksys Wireless Router :: SBG6580 And E4200 - Connection Keeps Dropping

Feb 4, 2011

I just got an E4200 and have a SBG6580 cable modem. I cant seem to set this up properly and my connection keeps dropping. What is the proper set up ? I would like to configure it so the cable modem handles the DNS and the E4200 handles the wireless.

View 4 Replies View Related

Linksys Wireless Router :: E4200 - Connection Drops And Timeouts?

Aug 26, 2012

I have the latest version firmware
 
I am constantly getting dropped and timeouts accross all of my devices this has been hapening for several months now I think ever since I upgraded to 1.0.04
 
It says no internet access when the wired computers have it fine.  Android phones, windows 7 pc, and chromebook. 

View 6 Replies View Related

Linksys Wireless Router :: E4200 Slow Connection Within Network?

Aug 4, 2011

I installed the E4200. Internet works fine, and the internet connection is maximum performance. But if I copy a file between laptops, or to my mediaplayer (AC Ryan HD2), the connection is 3MB/s tops. I changed to the 5gHz and N settings, still no change.

View 6 Replies View Related

Linksys Wireless Router :: Linux OpenVPN Connection Through E4200

Jul 6, 2012

When I try to connect OpenVPN through an E4200 v2 router from my Linux Fedora 16 client, the connection hangs. The connection log show that OpenVPN has connected to the VPN server. Internet also freezes until I disconnect OpenVPN.

OpenVPN on Windows works fine through the E4200 router.If I connect the Linux client directly to my Inteno fiber router, OpenVPN works fine.Passthrough is enabled in the router, and I have configured QoS and port forwarding for port 1194. The router has firmware version 2.0.37.

View 5 Replies View Related

Linksys Wireless Router :: Intermittent Dropped Connection With E4200

May 25, 2012

Bought an E4200 to replace my Netwgear router and am experiencing the following problem.One of my wireless boxes serves as mu mail server. I've been running this configuration for years so the only thing that has changed is the router.The neworkd is up and all wireless clients can connect, but after some time, access to the mail server just 'freezes'. I say freezes as the nework icon (i'm using ubuntu' still show a connection. In addtion, there are not error in any of the logs. I just seems that the mail server and the router just stopped communication.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - It Keeps Dropping Internet Connection

Jan 15, 2012

ever since i had a power failure losing all power in my apartment, my router has begun regularily losing connection to the internet, I have to go into the router and renew ip address which is quite annoying

[code]....

View 6 Replies View Related

Linksys Wireless Router :: E4200 Inbound Connection Timeouts?

Oct 9, 2011

So I recently purchased an E4200 to replace my aging and slightly ailing DLink DIR-655 which as served me well for going on 5 years.  The part of the DLink that was giving me the issues was the wireless, the routing and switching worked fine however.
 
I do quite a lot of streaming of media from my home machine outside my network through the internet.  Most recently I've been using Kalemsoft Media Streamer on my HP Touchpad, however I've used Zumocast, Windows Live, Splashtop, and a few others.  I havent yet tried my PPTP VPN through the router for an extended period of time to see if it reflects this issue as well though.
 
Since replacing my 655 with the E4200 I've started experiencing a timeout issue.  It seems to be semi-consistant and only happens after time of unuse or extended use (I havent timed it yet to see if it always happens after the same amount of time though).
 
Basically what occurs is this:
 
I'll be watching some video or listening to audio streaming from my machine and after a period of time (usually a long period of time) it'll suddenly lose connection, requiring me to re-connect through the software, like the NAT translation is timing out or something.
 
How it USED to work is this:  It'd basically work until I stopped streaming.
 
 My setup:
 
AT&T Uverse set to DMZPlus aiming towards my E4200 WAN port (sitting directly in place of the 655 I used to have)
 
All machines on the network are gigabit.  I have ports 7000 and 7001 open for Kalemsoft Media Streamer on the E4200 per the specifications of the software.
 
The software understands UPnP so I have nothing specific forwarded on my machine, but I didnt previously either.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved