Linksys Wireless Router :: Linux OpenVPN Connection Through E4200
Jul 6, 2012
When I try to connect OpenVPN through an E4200 v2 router from my Linux Fedora 16 client, the connection hangs. The connection log show that OpenVPN has connected to the VPN server. Internet also freezes until I disconnect OpenVPN.
OpenVPN on Windows works fine through the E4200 router.If I connect the Linux client directly to my Inteno fiber router, OpenVPN works fine.Passthrough is enabled in the router, and I have configured QoS and port forwarding for port 1194. The router has firmware version 2.0.37.
I just got a new E4200 v2 wireless router. I'm intrigued by the USB port, especially for using it to connect a printer. I currently have a D-Link wireless print server that I'm using to create a network-attached printer, but if I could remove an extra device and just have the printer connected straight to the router
Since firmware 1.0.02, E4200 supports connect printers to USB port and print to it from Windows using CiscoConnect.Is there any way to print from Linux (using CUPS, LPD, etc)?
I've got threeLinux Boxes (running Centos 6). They were all connected to my cheap WRT54GL-- DHCP worked every time.Absolutely no problems. Both the LInux boxes and the WRT54GL had MTU set to manual, 1492.I replaced the WRTt54GL with the expensive E4200. I set the new router's MTU to manual, 1492. NONE of my Linux boxes ever receive a DHCP address. I look at the logs, and they do DHCPDISCOVER, get DHCPNACK, try several different intervals, and then fail the interface and quit.ALL I did was unhook cables from the WRT54GL and plug into the E4200. Yes, the WRT54GL was powered off. NOTHING was changed in the Linux configs. Yes, DHCP is enabled, address-range assigned, etc. BTW-- one box is dual boot with Win7-- in Win7 (using the same card, obviously), DHCP works just fine. But, Linux doesn't work.
I can give the boxes static IP's, and all is well. Just can't get DHCP to work. I evfen tried putting in DHCP reservations (via MAC assignments) for the E4200-- still doesn't work. The new E4200 is on the 02 firmware (which I believe is cuurent). If I can't iron this simple task out, in a couple of days I'm taking the E4200 back, and getting a refund. I'll stay with my old WRT54GL... it works. Hate to give up on some of the new E4200 features, though.
(Setup routing and iptables for new VPN connection to redirect **only** ports 80 and 443) Only my goal is a bit different. I am running a headless gui-less install of Ubuntu Server 12.04 that is being used for a variety of different purposes... I would like all traffic to travel un-prohibited through my ISP except for my transmission traffic. I have a VPN i subscribe to that allows me access for which I only want to direct a single port's traffic to. I am currently using a modified version of the code from the above link. My current code is below:
My dad recently got a E4200 router, My whole family are mac users, the connection are all okay with their computers, I'm the only one using Microsoft, ASUS running on Vista. The connection is fine when I'm near the router, but when I go to my room I get no connection at all, it connects for a second but then it goes on connection with limited access.
Last week I bought the E4200 thinking it was probably the best router on the market and if it worked properly, it would be...I think.I have attached a Seagate GoFlex Desk 2Tb USB drive formatted to NTFS to the USB of the E4200. I can map to it from my Windows XP computer with no problem and I can FTP to it from any browser...my Windows 7 machine is another story. When I try to map the network drive from the Windows 7 machine I get error code 0x80070035 every time. I've seen some other threads where people are having this problem but in the cases I've found, they aren't getting any connection via XP or FTP either.
I have just installed Cisco Connect v1.4 (11266.0), and have upgraded my E4200 software to 1.0.03.I want to add a USB printer connected to the router but when I open Cisco Connect, and select the "Add new devices.....' button, the only option for a printer is 'Wireless Printer' not 'Printer' followed by USB or Wireless as per the User guide.
I have an E4200 (v1) with the latest firmware. For some reason, the E4200 does not allow me to conenct to certain websites. This is true for wired or wireless connections.To test, I connected a wired PC directly to my cable modem and was able to connect to all websites fine. I also tried an old D-Link router I had on hand and was able to connect to all sites fine. Went back to the E4200 and was blocked. I re-loaded the firmware and same results.
I have my e4200 connected to another modem/router (2Wire 3600HGV), because the other router does not support Wireless N. I can connect to my E4200 network, but there's just no connection to the internet. I reseted my e4200 but still no luck. I've unplugged both routers and replugged them, nothing. I know it's possible because I've had it set up before but I had my 2Wire exchanged for a newer one.
Firmware: 1.00.4
Just to be sure. I have the cable going from my modem out of port #1 and into my e4200 where it says internet, thats correct, right? On my e4200 i have the IP 192.168.1.2 but on the 2Wire I have the e4200 as 1.92.168.1.66.
The web site says that the E4200 has a USB port to connect USB drives and printers. That sounded to me like multiple devices could be added. It says nothing about only being able to connect one. Since I have 3 USB drives and 2 USB printers, that sounded great. Setting it up, it seems that this port will not use a HUB, and can only be used for one USB device. How can that be? That is so limiting as to be nearly useless.
I have an E4200 v1 wireless router. Intermittently, my hard wired laptop (and hard wired desktop) loose Internet connnectivity and when I look at the 4200 I see the status light flashing slowly like it was just rebooted. I am runnong 1.0.04, have reset to factory, reflashed the 1.0.04 code and done a 30-30-30 reset (so far no drops since the 30-30-30 reset but we'll see).
The problem: running a standard single band 2.4gz BT homehub. When using my xbox and wireless headset (razer chimeara) the xbox loses connection. When i tuen the headset off i no longer lose connection. This suggests to me that the headset is simply emitting on the same frequency and bullying the connection, thus the xbox disconnects I have purchased the wireless N adapter to allow the xbox to run on the 2.4 or 5ghz band. I am now looking for a duel band router to allow my xbox to connect to the 5gz band and hopefully this will rectify my interference issue with the headset. I have been lookijg at the e4200 as this supports seperate ssid for 2.4 and 5ghz band, so the xbox can run on the 5ghz and the intererence from the 2.4ghz headset should subside - do you think this would work? Also, with the single ssid duel band routers, where 2.4/5gjz share the same ssid - how would my wireless N devices know to run on the 5ghz and not the 2.4?
All my previous routers have allowed me to monitor my connection speeds however I can't find this in this router. I found the client table under "status" but I have not been able to find the connection speeds anywhere. I like to make sure that my devices are running at close to 300Mbps and not 54Mbps in case I have a connection setup wrong. I have searched in the forums without much luck.
I have a E4200 V1 with firmware 1.0.0.5 installed The problem is that when I connect the cable from my modem to my router and recycle both I get a rapidly fashing Cisco light and can not connect to the internet.If I remove that cable and recycle the router my network works but (obviously) I have no internet connectivity.This was working (almost 2 years) without issue until today.I updated the firmware and did a factory reset and neither resolved the issue.My next experiment is to see if I can't get log files (since the factory reset) but I can't do that at this time.
I bought a e4200 router about 3 weeks ago and after a power outage it decided it didnt like being connected to the internet anymore. So i got on the phone with cisco they determined the router was no good, mind you my laptop would connect wired. So they sent me a "refurbished" one, so i set it up. The new setup was wonky because it said the same message "Your connected to your router but..." then after trying to get the connection its self and failing it came up with "congratulations you are now connected to the internet". That lasted 3hrs and 45mins then died, so i went upstairs to power cycle it, it decided to connect with the old settings. That lased 25mins then died, so i reset it and reconfigured the router. Wouldnt connect, i checked my mac address and it was using my wireless one and kept turning on my wireless connection durring the install. So i cloned my wired mac address and got the internet for roughly an hour... then it died. So i reset it again and kept the wifi off got it going and decided to go to sleep. I wake up and its still working after 8hrs, i go down stairs with my tablet and i dies again. This time it refuses to reconnect, refuses to reset back up just doesnt want to work.
I just purchased e4200 from a friend of mine. Got an issue with setup of this device. I use a model from internet provider. Have 2 computers at home. One is pc with cable, another one mac with wireless.SO my issue is that i can not connect none of them. I was trying to use cd that comes with router but he can not locate a router. When I connect cable directly from modem to computer everything works fine. As soon I connect cable to a router I can not see a router and I can not connect to internet.
The latest Firmware for the E4200 states that there is now the ability to attach a printer to the USB port of the router. I am using a Mac, so that may be the problem, but I have followed the instructions on how to add the printer and it is not happening. It's possible that the MAC Firmware was not given the ability to add a USB printer like the PC Firmware upgrade.
I just got an E4200 and have a SBG6580 cable modem. I cant seem to set this up properly and my connection keeps dropping. What is the proper set up ? I would like to configure it so the cable modem handles the DNS and the E4200 handles the wireless.
I am constantly getting dropped and timeouts accross all of my devices this has been hapening for several months now I think ever since I upgraded to 1.0.04
It says no internet access when the wired computers have it fine. Android phones, windows 7 pc, and chromebook.
I installed the E4200. Internet works fine, and the internet connection is maximum performance. But if I copy a file between laptops, or to my mediaplayer (AC Ryan HD2), the connection is 3MB/s tops. I changed to the 5gHz and N settings, still no change.
Bought an E4200 to replace my Netwgear router and am experiencing the following problem.One of my wireless boxes serves as mu mail server. I've been running this configuration for years so the only thing that has changed is the router.The neworkd is up and all wireless clients can connect, but after some time, access to the mail server just 'freezes'. I say freezes as the nework icon (i'm using ubuntu' still show a connection. In addtion, there are not error in any of the logs. I just seems that the mail server and the router just stopped communication.
ever since i had a power failure losing all power in my apartment, my router has begun regularily losing connection to the internet, I have to go into the router and renew ip address which is quite annoying
So I recently purchased an E4200 to replace my aging and slightly ailing DLink DIR-655 which as served me well for going on 5 years. The part of the DLink that was giving me the issues was the wireless, the routing and switching worked fine however.
I do quite a lot of streaming of media from my home machine outside my network through the internet. Most recently I've been using Kalemsoft Media Streamer on my HP Touchpad, however I've used Zumocast, Windows Live, Splashtop, and a few others. I havent yet tried my PPTP VPN through the router for an extended period of time to see if it reflects this issue as well though.
Since replacing my 655 with the E4200 I've started experiencing a timeout issue. It seems to be semi-consistant and only happens after time of unuse or extended use (I havent timed it yet to see if it always happens after the same amount of time though).
Basically what occurs is this:
I'll be watching some video or listening to audio streaming from my machine and after a period of time (usually a long period of time) it'll suddenly lose connection, requiring me to re-connect through the software, like the NAT translation is timing out or something.
How it USED to work is this: It'd basically work until I stopped streaming.
My setup:
AT&T Uverse set to DMZPlus aiming towards my E4200 WAN port (sitting directly in place of the 655 I used to have)
All machines on the network are gigabit. I have ports 7000 and 7001 open for Kalemsoft Media Streamer on the E4200 per the specifications of the software.
The software understands UPnP so I have nothing specific forwarded on my machine, but I didnt previously either.
I purchased this router a few days after its release, and I was very impressed with its functions. I came from a DD-WRT flashed router with all the bells and whistles, and the E4200 lacked some features but I felt it was a fare trade off for the GHz & dual band.All was well with all my settings (quite a few to name QOS,forwarded, etc)I also updated the firmware when it came available and re entered same settings.
Approx 3 months after use I had 0 WAN connection via eth0 or WIFI, when I logged into router I was pulling a Public IP from my ISP. I could ping from inside the router but no connection on any hosts, very strange. Powercycling Modem/Router yielded same results.. I then backed up my vast amount of settings, and did a 30/30/30 reset.. With no configs I had no issue browsing on any host on my network. So I restored from backup and the issue was back again..So I did another 30/30/30 reset. Then went and reentered the exact same settings as before and the issue was gone.
I setup my E4200 v2 with different SSID's for 2.4 and 5GHz modes. I have no problem with a 2.4 Ghz connection on my laptop, but I cannot connect to the internet in 5GHz. mode. I choose the 5 GHz SSID and enter the passphrase but no luck, even though I have a full 4 bars inthe wireless icon.
my e4200 wireless. I have internet connection speed of 40mb and I have epc 3925 working in bridged mode as modem and E4200 as router. When I connect my laptop with wire on e4200 I am getting 37-38 Mbps on speedtest.net which is perfectly fine. But on wireless I am having a lot of dropping of speed: I have 2mps then jumping to 5-6 Mbps and so on it never goes more than 5-6 Mbps. When I disable WMM Support in QoS I am having perfectly constant 20mbps but... I have only g network 54mbps. [code]
my old D-link DGL-4300 was rock steady showing 54 Mbps constant speed (link rate) (in Windows 7 Home Premium 32 bit Wireless Network Connection Status window). The new E4200 jumps around from 72 Mbps to 114 Mbps to 130 Mbps to 144 Mbps. However, it mainly stays at 72 Mbps. I have seen 150 Mbps briefly but I have never seen 300 Mbps. I have even placed my laptop within 2 -3 ft of the router and have a strong signal (4 bars) but I still have the same link rate issue. I would think that Windows would show 300 Mbps link rate for my connection when it is that close to the router. My laptop is a Toshiba with an integrated Intel WiFi Link 5100 AGN wireless adapter. My son also has a Toshiba laptop with the same wireless adapter but he gets lower speeds than mine due to the fact that he is 50' away in another room in the house. His connection also jumps around but it is at lower link rates than mine.
my new E4200, replacing an E1000. In my net, at home, four computers are hooked up; 2 DELLs, 1 HP and 1 Vaio. All the computers are working fine with the new router but the VAIO notebook. I've installed the latest Firmware Version, 1.0.03. Done the new drivers on the VAIO. VAIO got intermintent net connection and nothing showed in the event logs. Worked fine with the E1000.
Sony VAIO: VPCEE45FB/BI Windows 7 - 64bits E4200: Firmware Version: 1.0.03
I have a WRT54G cascaded to an E4200 v2. I am closest to the WRT54G and connected at 54. If I am in range of the E4200, can I force a connection to it instead of the slower router?
I have a brand new E4200 with two desktop computers using it with no problems. I also have a work Thinkpad laptop that I use a couple of times a week from home. Since day one of installing the new router, I have experienced the blue screen of death numerous times during the day (the number of times varies from 1 to 6 on a really bad day). I believe this is happening when I lose my connection to the router. I can see it trying to reestablish itself but the VPN will drop the connrection before it has a chance. I never lost my VPN connection until the day I installed the new router. Yesterday, at least one time it was unable to reestablish connectivity with the router and I had to reboot the laptop to get it connected. Could this have something to do with the IP address? I do not have any issues with the laptop when I am at work using a docking station.
So, I am wondering why I am constantly losing connectivity on the laptop only. The laptop has Windows XP and I am using AT&T Global Network Client to access the work network. Is there a setting somewhere that will fix this? Our IT folks rebuilt my laptop and I am still experiencing the same problem. I checked and I have the current version of the firmware for the router.
