I have an E4200 v1 wireless router. Intermittently, my hard wired laptop (and hard wired desktop) loose Internet connnectivity and when I look at the 4200 I see the status light flashing slowly like it was just rebooted. I am runnong 1.0.04, have reset to factory, reflashed the 1.0.04 code and done a 30-30-30 reset (so far no drops since the 30-30-30 reset but we'll see).
View 9 RepliesI have a brand new E4200 constantly losing internet connection (both wireless and wired). I have a ADSL connection to the internet, last router I had did not have the same issue. I also have a Cisco ASA 5505 for work connected to the ADSL modem and is not experiencing any disconnect issues. All computers connected to the router is losing internet connection, local lan keeps working. The internet connection gets back again after a 10-15 minutes or when resetting / turning off the router.
I have tried the following;
Changed ethernet cables
Disconnected the ASA 5505
Turned off wireless
Upgraded the firmware
Reseted to factory settings
I recently updated the firmware to 1.0.02 on my E4200 and since then it's been rebooting randomly about once a day. It was working perfectly fine before the firmware update.
View 5 Replies View RelatedMy E4200 is rebooting every time it sees traffic on any port, including the internet port. It does not reboot itself if there is nothing plugged in.
Already tried: soft reset (power off for 30 seconds), soft reboot via back panel button, hard reset (press reset for 30, unplug and hold reset for 30, plug in while holding reset for 30).
I was using a netgear wndr 3400 and my network stream never failed. i bought a e4200 v2 and my tv loses streaming capabilities after about 10 to 15 minutes.i have to turn it off to get them back and then it does it again in 15 minutes. i know it is not the tv it wprked fine before the new router.
View 5 Replies View Relatedlinksys router problems Linksys wireless router connected to cable modem. over time router looses connection to internet. rebooting router reestablishes connection. running XP sp3 from laptop connected wirelessly?
View 3 Replies View RelatedI bought a Linksys router last summer for my PC and Xbox. The PC and XBox are hardwired into the router. About two weeks ago, my router began dropping connection throughout the day. Sometimes it happens 3+ times in an hour. Other times it works for several hours before it drops.I upgraded the firmware as one fix and did a hard reset of the router. Still drops connection.I changed the MTU to 1400 and it worked fine for several hours but then dropped again the next morning. Also, like others on the forums, when I changed the MTU and hit Save Changes, it just ran and ran, never timed out...but never showed that it finished the command to save (if you get my meaning).I downloaded the Cisco Wireless Magic program to troubleshoot. It tells the same thing everytime. Unplug your router for 10 seconds and start over...My PC sometimes flashes a warning when I am restarting the router that I am getting Limited or NO Connectivity.
View 7 Replies View RelatedI have to reboot my router a couple of times per day because I lose WAN access. This occurs with both the wireless and ethernet connections. Basically, I see that I'm connected to the router, but have a self-assigned IP. Power cycling the router does the trick. I never had this problem before, so I'm wondering what's up. The firmware has long been up to date. Router version is 8.0.
View 2 Replies View RelatedSo i have this old WRT54GX v2. It have been running fine for the last ~5years. But since this morning i'm losing my wired connection after about 10 sec og connectivity, can't even ping it when it drops. If i turn it off for 10 sec the same problem occurs. Tried both static ip and dhcp. Wireless doesn't work either.
View 5 Replies View RelatedI have a WRT400N that loses connections for my PC and other devices in my house (IPHONE, IPAD etc.).Sometimes it fixes itself other times I need to to a hard reset to boot the router and then evryone can signin again
The Firmware Version: 1.0.01 B19
The operating system on my PC is WIndows 7
I have a Linksys WRT120N wireless router that I have had for almost three years now. It recently has started dropping all internet connections very randomly, sometime multiple times in an hour. I will lose my connection to the internet and connection locally to other laptops then it will reconnect. It is also disconnecting when wired as well as I have a playstation using a wired connection out of the router and it loses connection all the time as well. What is causing this, I am pretty sure it is the router and not my internet service.
View 8 Replies View RelatedI often loose internet connection recently while online. I always check my status on 192.168.1.1 when this happen to see if i'm getting 0's ISP but it does not say that.I also tried ipconfig/release and renew I also tried right click wireless icon and click "repair"Power cycle always worked for me in the past but today to my dissappointment it did not.after power cycling I check my status on 192.168.1.1 and now it indicates 0's.
View 9 Replies View RelatedCurrently I have the ea 6500 and it seems to lose connection to my IPAD 3 often. I have setup the IPAD to connect to 5ghz connection and it will still lose connection. Is this an ongoing issue? I also noticed that it signal stength isn't fully covering my home like my linksys wrt54g did.
View 1 Replies View Relatedmy wrt320n keeps dropping internet connection and I have to keep unplugging it.
View 2 Replies View RelatedI've been having issues with my e2500 router. I've found my connection dropping occasionally both with a wired connection and wirelessly on other computer. My desktop is connected directly to the router via ethernet and I've been keeping an eye on my network preference pane. Every 10 minutes or so the connection will be lost and computer says the cable is unplugged. It then resolves after 2 minutes.
I'm running OSX 10.8, firmware 1.0.07. Done a factory reset, power cycles etc. Configured with Cisco connect and manually multiple times. I've swapped out ethernet cables just to be sure it wasn't a cable issue.
Internet is fine when I've got the computer hooked up directly to the modem. No connection issues.
I bought this new router, and at first it seemed like it was working okay, but then i started noticing that my roku box (watch netflix) was cutting out all the time, losing the connection from the new router. I also began to notice that if more than one person was online, pages took forever to load, can't watch youtube videos and even listening to music online like Pandora became difficult. Also it says that I can get up to 300 mbps but when i run the test I get .50 download and about 1.8 upload Details About Router & Connection,Its a Linksys E1500 with the capability of up to 6 devices and my IPS is Comcast.
View 1 Replies View RelatedI have a WRT54G router anf DSL modem. My router keeps losing connection, wired and wireless (My connection is not visible on any laptop). I tried briged mode on the modem and I tried the configuration CD. Everything works for some months or weeks. Sometimes the CD setup asks me for manual configuration. I am using modem to desktop connection?
View 2 Replies View RelatedI recently purchased a Linksys e3000 router. Everything is going great except that both my desktop (Windows 7 Machine) and Laptop (Macbook Pro) keep losing the connection to a DLINK 323 Nas drive I have plugged into the router. This is problematic because I keep my itunes library on the NAS drive.
View 1 Replies View RelatedI recently purchased a Linksys e3000 router. Everything is going great except that both my desktop (Windows 7 Machine) and Laptop (Macbook Pro) keep losing the connection to a DLINK 323 Nas drive I have plugged into the router. This is problematic because I keep my itunes library on the NAS drive.
View 2 Replies View Related- I am losing internet connections at least 1 time/ day. I have 2 wired and 2 wireless devices.
- when the internet is down I am connected to the router (wireless and wired, the connection is not lost/cable unplugged..).
- only when I power cycle the router I recover access to my admin page and internet connection.
* Firmware Version 1.0.06
Firmware 10.0.4 April 2012 WinXP SP3 AT&T Basic DSL Slipstream 5100 wired and wireless connection constantly drops then re-establishes connection every 15-30 seconds or minutes. How to fix this ventilation is not a problem nor the power source very close to switching to dd-wrt if no solution in 48hrs?
View 2 Replies View RelatedI recently upgraded my Wild blue internet service to the "Exede" system. When I kept losing the connection to my Mac Air book, the Wild blue service tech suggested that my wireless router (Linksys Wireless G 2.4 GHz router) was not robust enough to handle the increased "speed". They recommended I purchase a new router so I purchased the Linksys EA4500.
Now, after three weeks, the Linksys EA4500 router has stopped working. I am able to hook one of our Mac Books directly to the satellite modem to access the internet through an Ethernet connection. Finally, I finally reconnected my old Linksys Wireless G router to the modem to check to see if it would work and it does.
So, I'm wondering about the failure rate of the new Linksys EA4500 routers? Is there anything else I might try to get my new router to work??? I have unplugged it for an hour and then re connected it. I have pushed the reset button..My wireless indicator on the Mac Book Air shows full signal strength, but I can't connect to the internet with my new (less than 3 weeks old) router.
I am using the E2500 v1.0 on TWC network (road runner) wit a VISTA upgraded to Windows 7 laptop.After few months the router is starting losing connection. I tried connecting my laptop directly to the twc modem and the connection is fine, while if I connect to the E2500 v1.0, through wired or wireless connections, I see that the connection is going back and forth.I tried resetting the modem and the router, upgrading the wireless router firmware, but nothing worked.
View 1 Replies View RelatedRouter config and i just follow the instructions anyway i just bought this router cuz the old one failed and it was installed ok with internet connection and everything but when i open a program like bittorrent azureus the internet connection dies, it happens on my laptop and mac they both seem ok but when i open that program internet connection disappears
View 1 Replies View RelatedI'm constantly losing wifi connection and having to restart my Linksys E2500 router
View 4 Replies View RelatedI'm running Windows 7 64bit and I have sucessfully configured my wireless print server (Linksys WPSM54G) to work with my computer and our HP DesignJet 500ps. I have been able to print several sets of drawings without issue, however if the plotter is inactive for an extended period of time (1 hour +/-) the wireless print server loses connection with our router. At the same time the print server loses connection, an associate in our office with a wireless connection to his computer also loses connection to the router. A simple power cycle of the router and print server restores the wireless connection
I chatted with Linksys online tech support and they confirmed that I had the most recent firmware in both the router and print server and had me reconfigure some of the wireless settings on the router. All was good until about an hour ago when I tried to plot and discovered that the print server had lost it's connection to the router and my associate had also lost his wireless connection.
What's the deal here? I feel as though the root cause of this issue is related to the wireless router rather than the print server as my associate was periodically losing connectivity to the wireless router before installing the print server.
My LInksys router keeps losing internet connection. I have to unplug it and then plug it back in....
View 1 Replies View RelatedMy dad recently got a E4200 router, My whole family are mac users, the connection are all okay with their computers, I'm the only one using Microsoft, ASUS running on Vista. The connection is fine when I'm near the router, but when I go to my room I get no connection at all, it connects for a second but then it goes on connection with limited access.
View 5 Replies View RelatedLast week I bought the E4200 thinking it was probably the best router on the market and if it worked properly, it would be...I think.I have attached a Seagate GoFlex Desk 2Tb USB drive formatted to NTFS to the USB of the E4200. I can map to it from my Windows XP computer with no problem and I can FTP to it from any browser...my Windows 7 machine is another story. When I try to map the network drive from the Windows 7 machine I get error code 0x80070035 every time. I've seen some other threads where people are having this problem but in the cases I've found, they aren't getting any connection via XP or FTP either.
View 2 Replies View RelatedI have just installed Cisco Connect v1.4 (11266.0), and have upgraded my E4200 software to 1.0.03.I want to add a USB printer connected to the router but when I open Cisco Connect, and select the "Add new devices.....' button, the only option for a printer is 'Wireless Printer' not 'Printer' followed by USB or Wireless as per the User guide.
View 9 Replies View RelatedI have an E4200 (v1) with the latest firmware. For some reason, the E4200 does not allow me to conenct to certain websites. This is true for wired or wireless connections.To test, I connected a wired PC directly to my cable modem and was able to connect to all websites fine. I also tried an old D-Link router I had on hand and was able to connect to all sites fine. Went back to the E4200 and was blocked. I re-loaded the firmware and same results.
View 4 Replies View RelatedI have my e4200 connected to another modem/router (2Wire 3600HGV), because the other router does not support Wireless N. I can connect to my E4200 network, but there's just no connection to the internet. I reseted my e4200 but still no luck. I've unplugged both routers and replugged them, nothing. I know it's possible because I've had it set up before but I had my 2Wire exchanged for a newer one.
Firmware: 1.00.4
Just to be sure. I have the cable going from my modem out of port #1 and into my e4200 where it says internet, thats correct, right? On my e4200 i have the IP 192.168.1.2 but on the 2Wire I have the e4200 as 1.92.168.1.66.
The web site says that the E4200 has a USB port to connect USB drives and printers. That sounded to me like multiple devices could be added. It says nothing about only being able to connect one. Since I have 3 USB drives and 2 USB printers, that sounded great. Setting it up, it seems that this port will not use a HUB, and can only be used for one USB device. How can that be? That is so limiting as to be nearly useless.
View 3 Replies View Related