Linksys Wireless Router :: E4200 Rebooting Every Time It Sees Traffic On Any Port

Jun 15, 2012

My E4200 is rebooting every time it sees traffic on any port, including the internet port. It does not reboot itself if there is nothing plugged in.
 
Already tried: soft reset (power off for 30 seconds), soft reboot via back panel button, hard reset (press reset for 30, unplug and hold reset for 30, plug in while holding reset for 30).

View 9 Replies


ADVERTISEMENT

Linksys Wireless Router :: E4200 No Longer Sees Iomega 1TB External Hard Drive?

Jan 26, 2012

I had an Iomega 1TB External Hard Drive connected to my E4200 router.  I had shares confgured and they were properly running on the network.
 
As of yesterday, this all stopped working. The router does not see the drive; it is as though it is not plugged in.
 
I rebooted the router and it still does not work.  I've connected the hard drive directly to my PC to verify that it works there, and it does. The router is running Ver.1.0.03 (Build 14) of firmware (the latest).

View 9 Replies View Related

Linksys Wireless Router :: E4200 Rebooting After 1.0.02 Update

Jul 24, 2011

I recently updated the firmware to 1.0.02 on my E4200 and since then it's been rebooting randomly about once a day.  It was working perfectly fine before the firmware update.

View 5 Replies View Related

Linksys Wireless Router :: E4200 V1 Rebooting / Losing Connection?

Jul 5, 2012

I have an E4200 v1 wireless router.   Intermittently, my hard wired laptop (and hard wired desktop) loose Internet connnectivity and when I look at the 4200 I see the status light flashing slowly like it was just  rebooted.  I am runnong 1.0.04, have reset to factory, reflashed the 1.0.04 code and done a 30-30-30 reset (so far no drops since the 30-30-30 reset but we'll see). 

View 9 Replies View Related

Linksys Wireless Router :: E4200 Dropping Connection After Some Time

Nov 15, 2011

I bought a e4200 router about 3 weeks ago and after a power outage it decided it didnt like being connected to the internet anymore. So i got on the phone with cisco they determined the router was no good, mind you my laptop would connect wired. So they sent me a "refurbished" one, so i set it up. The new setup was wonky because it said the same message "Your connected to your router but..." then after trying to get the connection its self and failing it came up with "congratulations you are now connected to the internet". That lasted 3hrs and 45mins then died, so i went upstairs to power cycle it, it decided to connect with the old settings. That lased 25mins then died, so i reset it and reconfigured the router. Wouldnt connect, i checked my mac address and it was using my wireless one and kept turning on my wireless connection durring the install. So i cloned my wired mac address and got the internet for roughly an hour... then it died. So i reset it again and kept the wifi off got it going and decided to go to sleep. I wake up and its still working after 8hrs, i go down stairs with my tablet and i dies again. This time it refuses to reconnect, refuses to reset back up just doesnt want to work.

View 3 Replies View Related

Linksys Wireless Router :: E4200 Signal Fades Over Time

May 7, 2011

I have the e4200, well, I have had 2 e4200s and they both have had the same issue.I set up my e4200 manually with wpa2 security and I was getting about -50db rssi at my recieving device. Everything tested/worked fine and I went on with life.Without moving the router or anything else over the course of about 3 days the signal had dropped to -71dbm. I power cycled the router and it went back to -53dbm. I tried multiple channels and the same thing keeps happening.The same thing happened a few more times, I contacted tech support, but they just had me change channels.I took the router back for an exchange and the new one has done the same thing in LESS time!The router has the latest firmware and I keep it on an elevated plastic stand to prevent overheating.

View 6 Replies View Related

Linksys Wireless Router :: E4200 / Lion And Time Machine Backup?

Dec 21, 2011

Since lion is there for a while, it is still not possible to make a time machine backup on an USB hdd that's connected to the router.  is Cisco coming with an firmware update?

View 9 Replies View Related

Linksys Wireless Router :: E4200 Reboots Every Time When Use AirPlay From MacBook Pro

Oct 16, 2011

I've just confirmed that everytime I try to stream music from my MacBook Pro (iTunes) that is connected to my WiFi network using the 5GHz mode (channel width is Auto, channel: Auto (DFS)) to a couple Airport Express cubes are connected via the 2.4 GHz WiFi (channel width: Auto, channel: 10) the E4200 router reboots.  When I set the MBP to use the 2.4 GHz mode I can stream music without causing the E4200 to reboot.  The E4200 is running firmware 1.0.03.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Control On / Off Time Of Entire Guest Network

Sep 22, 2011

Can i control the on/off time of the entire guest network?Or can use parental control for computers logged onto the guest network? 

View 1 Replies View Related

Linksys Wireless Router :: E4200 Media Server Becomes Unavailable Most Of Time / Renders Device Useless

Feb 6, 2011

I have the new E4200 with an attached 750GB hard disk.All works well, however the media server becomes unavailable most of the time and renders the device useless.
 
I can connect to the Media Server from my xbox and laptop for an hour or so, and then all of a sudden it is gone. The only option I have is to reboot the router to bring it back online however not all of the music and videos are shown on the media server (yet).I uploaded quite a bit of music and video to the hard disk, I can initiate a scan but after a while the media server becomes unavailable / cannot connect to it.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - Block Popup Window That Displays Every Time In Form / Save Settings?

Mar 23, 2012

I just installed my new E4200, and am setting the Access Restrictions.  Is there anyway to block the popup window that displays every time I enter the form or save the settings?
 
I'm using IE9 and have tried adjusting the Popup Blocker, but to no avail.

View 7 Replies View Related

Linksys Wireless Router :: E4200 Allow VPN Connection / No Traffic Passes Can't Ping Across Tunnel

Oct 28, 2011

I have recently purchased a E4200 i have flashed it with the latest Firmware 1.0.03 and Hard Reset the Router so the Media issue was resolved i was having. After upgrading the firmware to the latest version my Nortel VPN IPSEC Client no longer will work. The tunnel is connected and it passes traffic for about 15 seconds then nothing.  The connection remains connected but no traffic passes cant ping across tunnel.  I have checked all the settings and VPN - IPSEC - Passthru is enabled.   I have put the client in DMZ mode and tried that same thing.

View 7 Replies View Related

Linksys Wireless Router :: E4200 - Stopped Allowing Traffic Through Ports Completely

Apr 24, 2013

I posted my complaint on Amazon.com recently.  My E4200 router stopped allowing traffic through ports completely.  I was able to unplug the power and allow the router to cool, and the router would work for a while then stop after about 10 minutes.  I assume that the unit was overheating, but I do not have the equipment of a test facility.I bought a Belkin AC 1200 router which is a bit of an upgrade from Amazon.com.  I do not think that there is anything that Linksys can do for me as my warranty expired.  I just thought that when I spent what was to me a lot of money the router should have lasted longer.

View 5 Replies View Related

Linksys Wireless Router :: System No Longer Sees WRT54G

Dec 29, 2011

I mistakenly downloaded and installed version 4 firmware when i should have installed version 2.  My system (windows ver. 7) no longer sees the wireless router (WRT54G).  I no longer have the install CD and the version 2 firmware does not seem to be available on the website.  Is my router now dead in the water? 

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Computer Sees Network But Can't Connect

Aug 28, 2011

So I have a WRT54G router since a couple of years now.  Laptop (Win7 64bit), ipod, ipad, phones can connect to it without a problem, but new computer (Win7 64bit) can't.  I can connect the PC via ethernet without a problem though.
 
I powercycled my devices, I changed broadcasting options off and then back on, changed my security mode, tried the MAC Cloning (after doing the MAC Cloning, I lost internet connectivity even through ethernet), resetted my security settings, changed SSID, I'm broadcasting through channel 11 2.462.  I also tried deleting the HomeGroup
 
Important fact: the network is in the list of available wireless network, but Signal Strength is No Signal and I can't connect to it. My network adapter is ASUS 802.11n Wireless LAN Card, drivers are up to date. I've upgraded to the latest router firmware.

[Code]....

View 4 Replies View Related

Linksys Wireless Router :: E4200 Port Forwarding?

Feb 26, 2013

I use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router  the port is closed. I followed instruction for port forwarding.

View 9 Replies View Related

Linksys Wireless Router :: Port Forwarding E4200 V 1.0.04?

Nov 2, 2012

I am trying to port forward my Linksys e4200 router v 1.0.04. However, it is not successful for when ever I check if the ports are open they fail they test.
 
I am sure that I am doing the actual port forwarding correctly (I hope), but something is refraining the ports from being open.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Detecting Port As Being USB 1.1

Apr 2, 2012

I have an E4200 and a WD MyBook Essential 2TB. They were working very well for the longest time, detecting a speed of USB 2.0. I had to get a new desk, thus had to disconnect all my devices, including the router. After plugging everything back in, the router only detects USB 1.1, even though the device is clearly USB 2.0.

View 5 Replies View Related

Linksys Wireless Router :: E4200 How To Close Port 139

Mar 15, 2012

So finally that my e4200 is capable of disabling wps i run in to another question.
how to close ports 139 445 ? these are open by default and i didnt figure out how to close them, in browser setup..
 
and YES port 139 IS a security issue. people denying this, are the same, that denied any vulnearibilties to wps.
 

View 1 Replies View Related

Linksys Wireless Router :: Open Port On E4200?

Sep 8, 2012

A external scan has reviled that I have an open port. For security reasons I want to close it. I do know the port number.

View 7 Replies View Related

Linksys Wireless Router :: E4200 Port Forwarding On TCP / 80 And 443

Aug 31, 2012

I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
 
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?

View 1 Replies View Related

Linksys Wireless Router :: E4200 Cannot Login To Ftp On Port Other 21

Oct 4, 2011

After updated firmware to 1.0.03 still can't log in to ftp on port other than 21 ( eg. 2121 ). Will it be fixed ever ? I told with guys on live chat but connection broked twice.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Block Traffic At Certain Times Uses Both Parental Controls / Internet Access Polices

Oct 21, 2011

I have configured my e4200 to block traffic at certian times uses both the Parental Controls and the Intenet Access Polices.  Neither one seems to work though.  [code] I have the same MAC addresses specified in each rule.  Initally I had only the first two rules.  Those didn't work, so I added rule 3 and 4 (they do the same thing as rules 1 and 2 but from the opposite direction).  There are no compliaints, but they don't stop any traffic. 
 
I started with the Parental Controls, they didn't work either.  The page in there that lets you pick which machines you want to block seemed next to worthless.  I have about four rows listed as "Network Device."  REALLY LAME!  As the MAC addresses are accesible and these weren't working I went to the IAP. 

View 5 Replies View Related

Linksys Wireless Router :: E4200 Port Forwarding Does Not Work?

Aug 18, 2012

I set up my new E4200 to forward port 7300 to a computer on my LAN.  I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work.  I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - Port Forward To Broadcast For WOL?

Jan 25, 2011

Some routers are able to forward to broadcast directly by sending a port to 192.168.1.255, other's I've been able to trick by forwarding to 192.168.1.254 and then editing the arp table with 192.168.1.254 <-> ff:ff:ff:ff:ff:ff. Is there any way I can edit the arp table of the E4200? Is there a way to telnet in or get a console connection?

View 9 Replies View Related

Linksys Wireless Router :: E4200 Must Be Connected To Switch Via LAN Port

Sep 2, 2011

I need a small number of computers connected to the Internet through the E4200.E4200 must be connected to the switch via the LAN port.The basic network is a network of class A - 10.xxx/255.0.0.0.How do I do?E4200 can not enter a mask of 255.0.0.0.

View 1 Replies View Related

Linksys Wireless Router :: Configured Port Forwarding On E4200

Oct 16, 2012

I have a Cisco E4200 with a Thecus NAS behind it. I configured port forwarding on port 80, 1080 and 4433 to access the NAS. However it's not working. Also tried to place the NAS in DMZ, but also I cannot connect it from outside my network. Inside my network, there is no problem.I also connected the NAS directly to the internet, and then I can access it from outside my network.I already tried a factory reset, disabled UPnP and IPv6, but nothing seems to work. I also replaced the router with a Cisco E3200, but it makes no difference.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G2V1 - Laptop Sees Secured Network But Unable To Connect?

Mar 11, 2012

I have a Linksys Wireless G Model WRT54G2V1 using WEP encryption.  I recently added a laptop.  It can access various non-decured netowrks.  It can see my home network but is unable to connect despite entering the correct passcode.  how to get the laptop and secured network to communicate?

View 1 Replies View Related

Linksys Wireless Router :: E4200 / Open Nat / Port Forward Xbox?

Aug 13, 2012

I'm using Cisco Connect Cloud to connect to my E4200 router. I wish to open my NAT type as currently its moderate on all games.Where the hell is the area to add the port ranges?? Is it even an option on the new connect cloud? If it is, it doesn't make it very easy to find. Would be allot easier if you had a tab/app for "Gaming/Applications" like you did previously.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Unable To Open Port 9000

Mar 12, 2012

Have a E4200 with version 1.0.04 firmware.Been trying to open 9000 to access my buffalo media server remotely. Have set up both Single Port  and Port Range Forwarding for port 9000.On trying to access media server, get message " could not connect to xxx.xxx.x.xxx:9000"Using online Open Ports Checkers shows this port is closed.

- Tried disabling all firewalls.
- tried range of ports
- Enabled/Disabled  UPnP
- tried cisco & buffalo tech support

View 5 Replies View Related

Linksys Wireless Router :: E4200 Failed To Port Forward Properly

Apr 5, 2012

A while back, I had my own minecraft server running. I had everything working and it was flawless. Then for some reason it just stopped working. I was Unable to open ANY PORTS. I did happen to try 65 - 110 and 254 - 210, as well as 12, 212 and 122. I dopnt know what happened but i have been searching everywhere on the internet (roughly 3 months)

View 1 Replies View Related

Linksys Wireless Router :: E4200 Non-supported Device Is Connected To USB Port

Dec 16, 2011

I'm trying to connect an Epson Stylus Color 740 USB printer to a newly purchased E4200 wireless router.  I've upgraded to the latest Cisco Connect software and to version 1.0.0.3 router firmware.  I get the message "A non-supported device is connected to your router's USB port.  Disconnect that device and follow the steps below to connect a USB printer to your router."  Cisco support was not beneficial. 

View 1 Replies View Related

Linksys Wireless Router :: E4200 - Use Hub To Connect NAS And Printer To Single USB Port?

Dec 28, 2011

E4200 -

Can I use a USB hub to connect NAS ~and~ a USB printer to the single USB port?

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved