Currently I have the ea 6500 and it seems to lose connection to my IPAD 3 often. I have setup the IPAD to connect to 5ghz connection and it will still lose connection. Is this an ongoing issue? I also noticed that it signal stength isn't fully covering my home like my linksys wrt54g did.
View 1 RepliesWe have a newer linksys router supporting 4 laptops, 2 desktops, 3 iphones, an ipad, an apple tv (also a smart tv, two wifi blu-ray players, but I'm less concerned about those devices). Everything is relatively new (1-2 years old). Most everything is turned on during the day but only a few things may be in use at a time.Many of my devices are loosing connection multiple times per day, my ipad is losing connection every 15 minutes, my apple tv takes a lot of finagling to connect (my level of tech expertise is basically me power cycling everything and prayer). Once my laptops get online, they tend to stick. It seems my apple devices lose signal more frequently.I've updated the firmware on the router and played with wideband settings and channel selection and haven't noticed much difference. I do see a lot of other wifi signals around me. The constant disconnecting has been going on for a couple of months. We have Comcast/Xfinity as our cable provider on 20/MB internet.
View 1 Replies View Relatedlinksys router problems Linksys wireless router connected to cable modem. over time router looses connection to internet. rebooting router reestablishes connection. running XP sp3 from laptop connected wirelessly?
View 3 Replies View RelatedIs there any way to connect my ipad to wet610n wireless-n bridge? the problem is that ipad don't have any Ethernet port..
View 1 Replies View RelatedI bought a Linksys router last summer for my PC and Xbox. The PC and XBox are hardwired into the router. About two weeks ago, my router began dropping connection throughout the day. Sometimes it happens 3+ times in an hour. Other times it works for several hours before it drops.I upgraded the firmware as one fix and did a hard reset of the router. Still drops connection.I changed the MTU to 1400 and it worked fine for several hours but then dropped again the next morning. Also, like others on the forums, when I changed the MTU and hit Save Changes, it just ran and ran, never timed out...but never showed that it finished the command to save (if you get my meaning).I downloaded the Cisco Wireless Magic program to troubleshoot. It tells the same thing everytime. Unplug your router for 10 seconds and start over...My PC sometimes flashes a warning when I am restarting the router that I am getting Limited or NO Connectivity.
View 7 Replies View RelatedI have to reboot my router a couple of times per day because I lose WAN access. This occurs with both the wireless and ethernet connections. Basically, I see that I'm connected to the router, but have a self-assigned IP. Power cycling the router does the trick. I never had this problem before, so I'm wondering what's up. The firmware has long been up to date. Router version is 8.0.
View 2 Replies View RelatedSo i have this old WRT54GX v2. It have been running fine for the last ~5years. But since this morning i'm losing my wired connection after about 10 sec og connectivity, can't even ping it when it drops. If i turn it off for 10 sec the same problem occurs. Tried both static ip and dhcp. Wireless doesn't work either.
View 5 Replies View RelatedI have an E4200 v1 wireless router. Intermittently, my hard wired laptop (and hard wired desktop) loose Internet connnectivity and when I look at the 4200 I see the status light flashing slowly like it was just rebooted. I am runnong 1.0.04, have reset to factory, reflashed the 1.0.04 code and done a 30-30-30 reset (so far no drops since the 30-30-30 reset but we'll see).
View 9 Replies View RelatedI have a WRT400N that loses connections for my PC and other devices in my house (IPHONE, IPAD etc.).Sometimes it fixes itself other times I need to to a hard reset to boot the router and then evryone can signin again
The Firmware Version: 1.0.01 B19
The operating system on my PC is WIndows 7
I have a Linksys WRT120N wireless router that I have had for almost three years now. It recently has started dropping all internet connections very randomly, sometime multiple times in an hour. I will lose my connection to the internet and connection locally to other laptops then it will reconnect. It is also disconnecting when wired as well as I have a playstation using a wired connection out of the router and it loses connection all the time as well. What is causing this, I am pretty sure it is the router and not my internet service.
View 8 Replies View RelatedI often loose internet connection recently while online. I always check my status on 192.168.1.1 when this happen to see if i'm getting 0's ISP but it does not say that.I also tried ipconfig/release and renew I also tried right click wireless icon and click "repair"Power cycle always worked for me in the past but today to my dissappointment it did not.after power cycling I check my status on 192.168.1.1 and now it indicates 0's.
View 9 Replies View Relatedmy wrt320n keeps dropping internet connection and I have to keep unplugging it.
View 2 Replies View RelatedI've been having issues with my e2500 router. I've found my connection dropping occasionally both with a wired connection and wirelessly on other computer. My desktop is connected directly to the router via ethernet and I've been keeping an eye on my network preference pane. Every 10 minutes or so the connection will be lost and computer says the cable is unplugged. It then resolves after 2 minutes.
I'm running OSX 10.8, firmware 1.0.07. Done a factory reset, power cycles etc. Configured with Cisco connect and manually multiple times. I've swapped out ethernet cables just to be sure it wasn't a cable issue.
Internet is fine when I've got the computer hooked up directly to the modem. No connection issues.
I bought this new router, and at first it seemed like it was working okay, but then i started noticing that my roku box (watch netflix) was cutting out all the time, losing the connection from the new router. I also began to notice that if more than one person was online, pages took forever to load, can't watch youtube videos and even listening to music online like Pandora became difficult. Also it says that I can get up to 300 mbps but when i run the test I get .50 download and about 1.8 upload Details About Router & Connection,Its a Linksys E1500 with the capability of up to 6 devices and my IPS is Comcast.
View 1 Replies View RelatedI have a WRT54G router anf DSL modem. My router keeps losing connection, wired and wireless (My connection is not visible on any laptop). I tried briged mode on the modem and I tried the configuration CD. Everything works for some months or weeks. Sometimes the CD setup asks me for manual configuration. I am using modem to desktop connection?
View 2 Replies View RelatedI recently purchased a Linksys e3000 router. Everything is going great except that both my desktop (Windows 7 Machine) and Laptop (Macbook Pro) keep losing the connection to a DLINK 323 Nas drive I have plugged into the router. This is problematic because I keep my itunes library on the NAS drive.
View 1 Replies View RelatedI recently purchased a Linksys e3000 router. Everything is going great except that both my desktop (Windows 7 Machine) and Laptop (Macbook Pro) keep losing the connection to a DLINK 323 Nas drive I have plugged into the router. This is problematic because I keep my itunes library on the NAS drive.
View 2 Replies View Related- I am losing internet connections at least 1 time/ day. I have 2 wired and 2 wireless devices.
- when the internet is down I am connected to the router (wireless and wired, the connection is not lost/cable unplugged..).
- only when I power cycle the router I recover access to my admin page and internet connection.
* Firmware Version 1.0.06
Firmware 10.0.4 April 2012 WinXP SP3 AT&T Basic DSL Slipstream 5100 wired and wireless connection constantly drops then re-establishes connection every 15-30 seconds or minutes. How to fix this ventilation is not a problem nor the power source very close to switching to dd-wrt if no solution in 48hrs?
View 2 Replies View RelatedI recently upgraded my Wild blue internet service to the "Exede" system. When I kept losing the connection to my Mac Air book, the Wild blue service tech suggested that my wireless router (Linksys Wireless G 2.4 GHz router) was not robust enough to handle the increased "speed". They recommended I purchase a new router so I purchased the Linksys EA4500.
Now, after three weeks, the Linksys EA4500 router has stopped working. I am able to hook one of our Mac Books directly to the satellite modem to access the internet through an Ethernet connection. Finally, I finally reconnected my old Linksys Wireless G router to the modem to check to see if it would work and it does.
So, I'm wondering about the failure rate of the new Linksys EA4500 routers? Is there anything else I might try to get my new router to work??? I have unplugged it for an hour and then re connected it. I have pushed the reset button..My wireless indicator on the Mac Book Air shows full signal strength, but I can't connect to the internet with my new (less than 3 weeks old) router.
I have a brand new E4200 constantly losing internet connection (both wireless and wired). I have a ADSL connection to the internet, last router I had did not have the same issue. I also have a Cisco ASA 5505 for work connected to the ADSL modem and is not experiencing any disconnect issues. All computers connected to the router is losing internet connection, local lan keeps working. The internet connection gets back again after a 10-15 minutes or when resetting / turning off the router.
I have tried the following;
Changed ethernet cables
Disconnected the ASA 5505
Turned off wireless
Upgraded the firmware
Reseted to factory settings
I am using the E2500 v1.0 on TWC network (road runner) wit a VISTA upgraded to Windows 7 laptop.After few months the router is starting losing connection. I tried connecting my laptop directly to the twc modem and the connection is fine, while if I connect to the E2500 v1.0, through wired or wireless connections, I see that the connection is going back and forth.I tried resetting the modem and the router, upgrading the wireless router firmware, but nothing worked.
View 1 Replies View RelatedRouter config and i just follow the instructions anyway i just bought this router cuz the old one failed and it was installed ok with internet connection and everything but when i open a program like bittorrent azureus the internet connection dies, it happens on my laptop and mac they both seem ok but when i open that program internet connection disappears
View 1 Replies View RelatedI'm constantly losing wifi connection and having to restart my Linksys E2500 router
View 4 Replies View RelatedI'm running Windows 7 64bit and I have sucessfully configured my wireless print server (Linksys WPSM54G) to work with my computer and our HP DesignJet 500ps. I have been able to print several sets of drawings without issue, however if the plotter is inactive for an extended period of time (1 hour +/-) the wireless print server loses connection with our router. At the same time the print server loses connection, an associate in our office with a wireless connection to his computer also loses connection to the router. A simple power cycle of the router and print server restores the wireless connection
I chatted with Linksys online tech support and they confirmed that I had the most recent firmware in both the router and print server and had me reconfigure some of the wireless settings on the router. All was good until about an hour ago when I tried to plot and discovered that the print server had lost it's connection to the router and my associate had also lost his wireless connection.
What's the deal here? I feel as though the root cause of this issue is related to the wireless router rather than the print server as my associate was periodically losing connectivity to the wireless router before installing the print server.
My LInksys router keeps losing internet connection. I have to unplug it and then plug it back in....
View 1 Replies View RelatedWhen using my pc through my wireless Netgear router, the connection is lost periodically and I get the message "default gateway not accessible". It only happens on my PC, and not on my IPad. What should I do to keep the connection on my PC?
View 1 Replies View RelatedMy LG BD570 is losing connection about 30mins in while I'm streaming an .avi from my desktop.This problem has only been happening since I setup my new wireless router. Belkin N300.I have no other network problems between my computers or simply using the internet.I did not have this problem previously when I was using an older Belkin Wireless G+ Router.
View 4 Replies View RelatedI have a Cisco Aironet c where it is configured as an AP. I use a Pocket PC to access the AP, but after a period of use, the Pocket PC loses communication with the AP for a short period of time and the application that is utilized in the pocket closes. After a few seconds it automatically connects. Searching the logs of the AP found the following warning: "Packet to client 0017.2302.8a5e Reached max retries, removing the client", but this is not always alert appears.
View 0 Replies View RelatedI have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81. I'm not sure if this is an issue with the WAP or the router.
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time. I used to have the power settings such that it didn't power down completely even after a long time. With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died. The wireless link would report that it had a solid connection, but I couldn't connect to anything. Power cycling the WAP always fixed this.
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours. Now, it seems I can't even go one day without losing my connection.
I am running the latest frimware in the WAP, and the router is version 3.1. I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen. I know from past experience that I will have to power cycle it to get it to talk to me again.
In any event, it seems like the router connection to the WAP is timing out. I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.
I have a new iPad and a new WAG160N. I've wasted many hours trying to get them to recognize each other, with no success.I can connect to the Internet OK but I can't get a connection to the Pad, as it won't accept my password. I can't find a solution here that I can follow for this model.Why won't my password (no unusual symbols, just 10 letters and numbers) be accepted?
View 9 Replies View RelatedCurrently using a netgear WG602 wireless router which i use to connect to my 2nd PC and Iphone, with the Netgear router running from my main PC.I have recently been having trouble with my 2nd PC ad Iphone randomly losing connection and the only way for the connection to be reastablished is to reboot the wireless router. Once rebooted i am able to connect again to the internet with no problems, interestingly enough my main PC never loses connection. Also sometimes when i lose my connection and reboot the wireless router i will have a IP conflict pop up on my 2nd PC however i would i say i get this once in every 10 dissconects and not all the time. Sometimes i won't dissconect at all in a day but sometimes i may dissconect 5-6 times.
View 1 Replies View RelatedThere are 2 ps3,a wii ,2 laptops,3 desktops,2 dsi.We have been having issues for a while now with losing connection and the service provider says there is nothing wrong. the modem is a comtrend ct-5072t and the router is a linksys E3000. The E3000 is the 3rd router I have bought in the last yr and 1/2 the last was a d-link dgl4500 gaming router the modem is new a rentel from the provider. Downloading updates for the ps3s are a nightmare online games like arma2 and battlefield 3 are a pain because we are losing connection all the time dont know what to do.
View 4 Replies View Related