Linksys Wireless Router :: Cisco Wet610n Connection To Ipad?
Aug 6, 2012Is there any way to connect my ipad to wet610n wireless-n bridge? the problem is that ipad don't have any Ethernet port..
View 1 Replies
ADVERTISEMENT
Linksys Wireless Router :: EA 6500 Losing Connection To IPad 3
Dec 6, 2012Currently I have the ea 6500 and it seems to lose connection to my IPAD 3 often. I have setup the IPAD to connect to 5ghz connection and it will still lose connection. Is this an ongoing issue? I also noticed that it signal stength isn't fully covering my home like my linksys wrt54g did.
View 1 Replies View RelatedLinksys Wireless Router :: Setting Up E4200 With Wet610n?
Jul 7, 2011I'm moving into a new house. I've purchased the E4200 and the WET610N so I can connect between the main house and the carriage house which will be my office. Carriage house is 60' away from the main house. I want to place the E4200 in the main house and will send it the broadband cable signal from the cable modem. I'll wire ethernet directly from the E4200 to the DVR for DirecTV and will use another output to distribute to other computers in the main house via ethernet switch. I will place the WET610N in the carriage house and want to take to output from the WET610N into wired ethernet switch(es) there for access to the broadband from the house.
View 9 Replies View RelatedLinksys Wireless Router :: E4200 Won't Connect With WET610N Via N After 1.0.04 Update
Apr 28, 2012After I updated my E4200 V1 with the 1.0.04 update I am unable to connect my WET610N to it with 802.11N. I can connect fine with 802.11G. I tried the Site Survey method of pairing them as well as manual. When it fails it goes through the minute timeout of trying and then Link Status is disconnected. I have anything from phones to laptops connect to the E4200 with wireless N, its just the WET610N that doesnt want to pair.
Before I was running the following:
E4200 V1 1.0.03
WET610N V1 1.0.05
Connection between them: Bridged, WPA2 Personal, 802.11N
After I was running:
E4200 V1 1.0.04
WET610N V1 1.0.05
Connection between them: Bridged, WPA2 Personal, 802.11G
Linksys Wireless Router :: Connecting Bridge (WET610N) To E2500
Feb 25, 2012just replaced my WRT54GL with e2500 and i have a problem connecting my bridge (WET610N) to e2500 router, it connects fine, but no internet when i connect the bridge to another PC (bidrge says it's connected and got IP), same story with another router (WRT54GL) i connect it with the wire to the e2500 than connect to that router with wi fi and OOPS no internet when i connect to e2500 directly with laptop, iphone etc i have the internet connection, but when i connect the bridge or another router i get no internet looks like E2500 does not let the internet pass throught the bridge or other router.
View 3 Replies View RelatedLinksys Wireless Router :: Connecting A WET610N To WRT54GS To Expand Range
Aug 4, 2011I have a wireless network in a 2 storey house. The internet access and 1 WRT54GS router is on the 1st floor (using frequency channel 11). The wireless single doesn't do very well on the second floor unless there is a device with a strong antenna. I recently purchased a WET610N Bridge and I have an extra WRT54GS (using frequency channel 1).
I would like to be able to add wireless to the 2nd floor by attaching the extra router to the bridge which would wirelessly connect to the router with the internet.
Linksys Wireless Router :: E4200 And WET610N No Changes To Bridges Before Firmware Update
Feb 6, 2012Okay so I have been using my E4200 router and WET610N bridges for a while now without any issues really until yesterday when I updated the firmware on the 4200 now none of my WET610N's (I have 2) can connect via wireless at all. At first I thought it was a a wireless issue but I have other devices that connect up just fine via wireless.I've made no changes to the router or the bridges before the firmware update.
If I hook the bridge directly to the router I can access it and configure it, but looking at the "Status" page, I see the bridge try and connect wirelessly but is quickly disconnected. Range isn't an issue as in my testing the bridge was 2 feet from the router.I've update the bridges to the latest firmware and have verified a 100 times that the settings on both my router and the bridges are set correctly (when the bridges are hooked up via network card).
Linksys Wireless Router :: Using WET610N And WRT320N As Bridge Within Home Network?
Mar 5, 2010I have a small home network, in which the DSL modem is some way away from the room in which I do my work. Currently, I use a pair of WAP54G access points to bridge between the two locations, and everything works OK, if slowly.Today, I bought a WRT320N router and a WET610N bridge to replace the access points, but I having a real problem configuring them to work. I think the basic problem is with the IP addresses that they use. The current configuration is:
DSL Modem -> Access Point -- several yards -- Access Point -> PC
and I want to go to:
DSL Modem -> WRT320N -- several yards -- WET610N -> PC
I guess my basic question is this a reasonable idea or should I be using something different for the WRT320N end? I don't want to change the basic IP address subnet (192.168.1.*) and I want to keep the DSL modem as the default gateway (192.168.1.254). When I installed the WRT320, it assigned itself an IP address of 192.168.0.1 and the WET610N an IP address of 192.168.0.101, and I think the DSL modem also assigned the WRT320 an IP address of 192.168.1.99, so I am a little confused as to which IP addresses I should be setting where.
Linksys Wireless Router :: Using Bridge WET610N To Stream Media To Living Room?
Aug 25, 2011At home I am using the linksys wireless bridge WET610N to stream media to my livingroom. The setup looks like server <-> Linksys E4200 <-> WET610N. If I connect my laptop to the WET610N i get a speed close to 100Mbit/s. With this speed I can easily view HD movies, by playing them on my laptop. So far so good...But if I instead connect my Popcorn Hour A-100 (a media player) , to the WET610N (instead of the laptop) I get really poor performance. just a few Mbit/s, which is not enough.So my question is, why is the following setup working fine:server <-> Linksys E4200 <-> WET610N <-> LaptopWhen at the same time the following setup is working poorly:server <-> Linksys E4200 <-> WET610N <-> Popcorn HourThe WLAN connection between the Linksys E4200 and Linksys WET610N seems to be fine. The problem I am having seems to be the Ethernet connection/setup between the WET610N and the Popcorn Hour media player.
View 1 Replies View RelatedLinksys Wireless Adapters :: WET610N Bridge And WRV54G Router Combo Not Working?
Feb 16, 2010I recently purchased the WET610N Wireless Bridge to use with my Samsung BD-P1590 Blu-Ray Player. The player has a few built in apps that include Netflix, Bockbuster, Pandora and YouTube. I successfully setup the bridge and hooked it up to the blu-ray player. It wasn't that hard. All the internet apps on the player work fine except Netflix. The first time I use the netfix app, it is supposed to give me a code that I use to register the device with netflix. However, I get a message that Netflix is temporarily unavailable. I have called netflix and they assure me that this is not the case and that it is most likely my wireless setup. The troubleshooting on Samsungs website points to the same thing. With that said, I disconnected the player from the wireless bridge and wired it directly to my router. Netflix works just fine then. Below is a list of things I have attempted:Disable the firewall on the router to see if it was blocking the app. (had the same results)Checked my firmware on all my devices (they are all current)Powered down all my devices and started them up back up starting with my DSL modem and ending with he blu-ray player (same results)Configured the bridge and player to use a static IP vs using the IPs automatically assigned by the router. (same results)Disabled aggregation on all WMM categories. I don't think the WRV54G router supports aggregation,, so I though this might cause a conflict with my setup. (same results)Enabled the broadcasting of SSID (same results)Chatted with linksys support. They basically checked to see if I had the latest firmware and that the bridge was working. They then recommended that I exchange the bridge for a new one. (I have not exchanged it for a new one yet, just because I am not convinced that there isn't something else wrong with my setup)My Configuration
DSL Modem --> WRV54G Linksys Wireless Router --> WET54G Wirelss Bredge --> Samsung BD-P1590 Blu-Ray Player
Router is broadcasting in Wireless G only on channel 1
Using WAP-PSK encryption
I am not sure if the problem lies with the routewr or the bridge. I am hoping someone out there can confirm that the WET610N truly does work whne using it with a BD-P1590 blu-ray player. This would lead me to believe that there is something wrong with my configuration or with using it combination with my older router. I would like to note also, that I have had one instance where BD Live didn't work. However, it has worked on other disks.
Linksys Wireless Adapters :: No Internet Access With WET610N?
Nov 21, 2012I have a WET610 that I intend to use to connect a PC to the local network and further on to the Internet. The local connection works, I can ping to and from the computer connected to the WET610 and I can see the other computers, both wired and wireless, on the network so the wireless connection is ok but I can't connect to the Internet, I can't even ping the DNS I'm using. What can be wrong? All the other computers can access the Internet. The WET610 talks to a wireless AP which in turn is connected to a router
View 9 Replies View RelatedLinksys Wireless Adapters :: WET610N Not Passing DHCP?
Feb 7, 2010I have the bridge working but I have to assign a static IP address to devices connected to it. I can't get it to pick up an address from my DHCP server. Here's what I have:
Cisco ASA5505 (Firewall & DHCP server)
WAP54G - Access Point
WET610N - This Wireless Bridge
The ASA5505 successfully gives DHCP address to ALL wired and wireless computers. The WET610N has connectivity to the WAP54G. The status page indicates it's connected and I can get on the internet if I set a static address. However, once I configure my computer to automatically get an IP from DHCP, it just times-out and says limited or no connectivity. Again, when I set a static IP, I have connectivity to everything. I know the AP is working because I can get an address from my DHCP server (ASA5505) with my other laptops and even my cell phone. Why can't I get a DHCP address through this bridge (WET610N)?
Linksys Wireless Adapters :: WET610N Signal Strength
Jan 27, 2011I have a WET610N on my network with very little signal strength. My set up is:
Router E3000
48 ' (48 feet) to
WET610N
The WET610N is on 5Ghz N, and is the only device at Ghz, and indeed the only wireless device during testing.
The use for the adaptor is to connect an Xbox 360 as a MCE for Video streaming.It is unusable, with unwatchable lags and intermittent failures.The 'Network Performance Monitor" doesn't read in mb/s, but essentially I get about 1 or 2 'bars', well under the acceptable for Standard def reading.
zInterestingly, when I bring the device within 3 feet of the router, I get great speeds (30 Mb/s down), but the bit rate reading in the status screen reads lower than the below reading.
Below is at the 45 foot mark->
Link Status:Connected MAC Address:68:7F:74xxxx:31 Network Name (SSID):sx BSSID:98:FC:11:xxxx9:94 Radio Band:5 GHz Channel Width:20 MHz Wide Channel:N/A Standard Channel:36 Bit Rate:43.3Mbps Signal:10% Security:WPA2 Personal
Linksys Wireless Adapters :: WET610N Bridge With Multiple Devices?
Dec 11, 2009I am interested in purchaseing a WET610N wireless Bridge for my new XBOX 360 to connect to my existing wireless, and wire network. I was wonder if the device can be connected to a 5 port network switch and used on multiple devices such as my TV.
View 5 Replies View RelatedLinksys Wireless Adapters :: WET610N Crashes And Restart After 10 Minutes?
Jan 30, 2010My WET610N crashes when I'm using it behind my PS3 while I'm watching videos in DLNA with the PS3 Media Server. Sometimes I can watch it during 1 hour without problem, somtimes it crashes and restart after 10 minutes of playing already. The restart is taking quite a long time, something like 2 or 3 minutes to get back to a Wifi connection. The router is still working properly while the WET610N is restarting.
The firmware is the latest 1.0.03, the settings are made for Video Access mode. I'm not using any encryption, only MAC address filtering.
My Wifi router is a Belkin N+ (F5D8235-4 v2000).
Linksys Wireless Adapters :: WET610N Setup Wizard Disc For Mac?
Oct 10, 2009The "Setup Wizard" disc that came with my WET610N won't work in a Mac. Is there a disc or a download available?
View 6 Replies View RelatedLinksys WET610N - Windows Constantly Ping Wireless Network Bridge
Jun 23, 2012I was looking at a Wireshark capture off my Windows XP box, and I noticed a rather curious behavior. Every 1-2 seconds, the machine sends a ping request to my Linksys WET610N wireless network bridge, which the Windows box connects to the Internet through.
View 1 Replies View RelatedLinksys Cable / DSL :: WAG160N Can't Get Connection To IPad / Won't Accept Password
Sep 29, 2011I have a new iPad and a new WAG160N. I've wasted many hours trying to get them to recognize each other, with no success.I can connect to the Internet OK but I can't get a connection to the Pad, as it won't accept my password. I can't find a solution here that I can follow for this model.Why won't my password (no unusual symbols, just 10 letters and numbers) be accepted?
View 9 Replies View RelatedLinksys Access Point :: WET610N Shows Hard Wired Not Wireless With Xbox 36
Dec 27, 2012I have an E4200 router with 3 WET610N access points. I did the firmware update on the router, E4200, about 2 weeks ago so my son could use his xbox when he got home after 4 months of being away. Everything seemed to work OK as far as I could tell....but when he went to sign into xbox live and watch Netflix, it will load to 98% and stop. A friend of his came over with the new Slim xbox 360 with built in wireless and it will connect fine on its own, if we hook up one of the 610N's to it, it will load to 98% on Netflix and stop again with error code R8152. Both of my older xbox's will hook up and play on xbox live, just not work with Netflix.I also noticed, it shows the WET610N as a hard wire on xbox and will not search for any wireless networks, I have 2. The newer Slim xbox360 will search out both networks on its own if you allow it to use its internal wireless. This only happened since the firmware update.
View 3 Replies View RelatedLinksys Wireless Router :: Connect IPAD To WRT160n?
Feb 23, 2012How do I connect IPAD to Linksys router WRT160n?
View 2 Replies View RelatedLinksys Wireless Router :: How To Set Up E1200 Wifi For Ipad
Dec 26, 2012I received a Linksys E1200 Wi-Fi Router for Christmas. I inserted the Setup CD into my iMac, running OS X version 10. 8. 2. I clicked on setup and a window opened with the message "Unsupported operating system".At this point I don't plan to use the Wi-Fi for the computer, but I do need to connect the ethernet cable to the router, then to my computer.I will be using Wi-Fi for my iPad. In that case, I have no instructions on how to set up the router for my iPad. Will this Wi-Fi router work or will I need a router compatible with OS X version 10.8.2?
View 1 Replies View RelatedLinksys Wireless Router :: E1200 Won't Connect To Ipad
Apr 21, 2012We have just installed the E1200 wireless router. We are able to access the internet from our home computers, however we cannot get the IPAD connected. When we try to find our wireless network to connect to it doesn't display yet our we can still see our neighbors wireless networks.
View 1 Replies View RelatedLinksys Wireless Router :: WRT320N - IPad Can't Connect To It
Jul 24, 2011I have a WRT320N router with firmware version 1.0.01 build 008. I just got an iPad and while it can find my router, I can't access the WiFi when I enter my password. I can use the router with my laptop so I know the connection and password are ok.I've seen two administrators on here suggest the same thing. And one person responded that it worked. The identical directions were:
Try changing some advanced wireless settings on the router.Connect the computer to the router with the Ethernet cable. Open the setup page of the router.Click on wireless tab and set the configuration view to manual. Change the wireless channel to 11. Save the settings.Go to wireless tab and click on Advanced wireless settings.Change Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.Try to connect to the wireless network again and see if that works.
1 - I think my computer already is connected to the router with the Ethernet cable - I mean there is an Ethernet cable attached to both my computer and my router - in slot 1 on the router
2 - the only thing I know how to access is the Linksys EasyLink Advisor. What and where is the setup page of the router?
Linksys Wireless Router :: WRT160N V3 With Direct TV And IPad
Dec 11, 2012I am trying to use the directv ipad app to watch/control my directv service. I am not able to see the DVR that is on my system. It is plugged directly into the router and the other receivers (and ipad) are wireless connecting through the same router.Direct TV says:
"For added security, some brands of routers treat Wi-Fi as separate from an Ethernet cable connection within the same router. If your HD DVR is connected to the router by Ethernet cable, and the iPad to the router via Wi-Fi, they may not see each other. Check your router manual as you may need to configure your setup."Can someone tell me if the WRT160N considers them as two separate networks when connected via wireless vs plugged in?
Linksys Wireless Router :: E2500 Won't Connect To IPad?
May 14, 2013What should i do ? Reset ? How ? maybee i did not set the cable properly ( what is an ethernet cable ? ) the one i have is a short cable with what looks like telephone jacks at either ends. one end is plugged in my comcast modem and the other into my mini mac.
View 1 Replies View RelatedLinksys Wireless Router :: WRT54GS Won't Work With New IPad?
Apr 4, 2013My WRT54GS works fine with my wireless computer. I just tried using the router to work my wireless IPad and it wont work. The WiFI sees the router, and when I type in the router password, Linksys shows on the WiFi , but it won't download it and show a wireless icon, or let me go online. I looked in the router information and it said my version is v.1.50.9
ON the router, after the model number says ver.6. I see a 6 for downloading a firmware upgrade, but no 1.50. Any solution other than having to buy a new router?
Linksys Wireless Router :: IPad Not Connecting To Cisco Connect Using E4200?
Aug 27, 2011I have an E4200 wireless router which is connected via USB to my Canon MX 308 printer. I am able to print from Windows computers that are connected to this router (via WiFi of course). My iPad 2.0 is able to connect to the internet via the router. However I am not able to print content from my iPad via the E4200 router (via Wifi using Cisco Connect software).
View 1 Replies View RelatedLinksys Wireless Router :: Can't Connect Iphone / Ipad To E1500
Mar 22, 2012i got my ps3 & xbox to connect it was easy but when i go to connect my iphone it doesnt even let me put my password in it just says"cant connect"?
View 3 Replies View RelatedLinksys Wireless Router :: E2500 - Connecting Ipad To Wifi?
Mar 5, 2012Have set up Router OK. Created Flashdrive EZ
How do I connect my IPAD now to WiFi since there is no USB port on my Ipad??
Linksys Wireless Router :: IPhone And IPad Cannot Connect To E1500
Jun 26, 2012I recently connected E1500 to time wanrner cable modem for my home. 3 laptops work fine, but iphone and ipad can not connect to wireless. But iphone and ipad connected to linksys guest automatically.
View 4 Replies View RelatedLinksys Wireless Router :: EA6500 - IPad Is Not Listed In The Devices?
May 14, 2013As I write this my iPad is connected to my Linksys router. However, my iPad is nor listed as a device in the list of all connected devices. All my other devices are listed just fine. Why I can't find my iPad?
View 1 Replies View RelatedLinksys Wireless Router :: Connect Ipad To E1200 As Another Computer?
Mar 26, 2012I don't want to allow any Guest access to my network, but I do want to connect my iPad to my network. I've successfully added another computer to the network but the router setup seems to want the iPad to connect only as a Guest .Is there a way to treat my iPad as another computer (not as Guest) so that it my network recognizes it in the same way it recognizes the second computer (without entering a password)?
View 1 Replies View RelatedLinksys Wireless Router :: EA-4500 - Download Speed Too Low Using IPad
Nov 17, 2012I use steed test appnto check the speed of my wireless. I am connected to 5ghz band and using the app most of the time my download speed are between 10-20 Mbps (red line range in app). I noticed that some posts are referring to download speeds of 50mbps. Are my download speed too low? I am in ontario cogeco isp
View 1 Replies View Related