Linksys Access Point :: WET610N Shows Hard Wired Not Wireless With Xbox 36
Dec 27, 2012
I have an E4200 router with 3 WET610N access points. I did the firmware update on the router, E4200, about 2 weeks ago so my son could use his xbox when he got home after 4 months of being away. Everything seemed to work OK as far as I could tell....but when he went to sign into xbox live and watch Netflix, it will load to 98% and stop. A friend of his came over with the new Slim xbox 360 with built in wireless and it will connect fine on its own, if we hook up one of the 610N's to it, it will load to 98% on Netflix and stop again with error code R8152. Both of my older xbox's will hook up and play on xbox live, just not work with Netflix.I also noticed, it shows the WET610N as a hard wire on xbox and will not search for any wireless networks, I have 2. The newer Slim xbox360 will search out both networks on its own if you allow it to use its internal wireless. This only happened since the firmware update.
I'm trying to use the WET610N as a sort of access point/range extender for a single device, a remote monitoring system installed in a barn. It records temperature, power use, etc, and reports it to the internet. The barn is about 250 feet from the house where the wireless router is installed. There will be very little data flowing over the link.Setup on the WET610N went fine, and it saw the remote router at 10% strength and connected to it fine. However, when I attempt to get Status, the screen shows the headings on the left and no data on the right. Attempting to access the internet through the link on my MacBook Pro failed.
I am having trouble connecting my device to certain WiFi networks. We work with hotels and we have a handful of devices that are just not able to connect to their network. Te device works fine in my office. When I get to the Setup page and do a site survey, it'll get to 100% and then display a "page can't be found" as oppose to showing me that it has been connected. We had the MAC address cleared in their network and still no luck. Firmware has also been updated.
Is there any way to use the e2500 without having hard wired internet access. I would like to use with my wii fii hot spot so that I could use my old printers that are not wireless enbled
I have a WES610N in my office connected to a E4200 @ the cable modem in the family room. ~30'.The connection is fine and works well when working.Connected to the WES610N I have:
-Polycom VOIP phone -HP Mediasmart Windows Home Server -Desktop -Multi-Function Laser Printer
I have two issues.
1) The Polycom does a random reboot that I have traced down to it loosing it's IP 2) The Windows Home Server looses it's IP requireing a hard reset.
I have enabled QOS for the polycom and that just worked with managing data. However both devices seem to loose their IP regularly. The desktop might also be having the issue but because it is Vista I suspect Vista is better equipped to deal with IP issues.
1. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
I work at a small business that has an exisiting wired network. Our setup is: Internet > ISP Box > DHCP Server > Switch > Users. I have been attempting to add a wireless router to the network to enable our shop techs to wirelessly access our file computer. I have managed to get the wireless working, but the network was not visible, I could not access any network computers from the wireless, and I could not access the wireless router from our main server. After this I screwed up the settings completely and even a wired connection to the router couldn't connect to the internet. Now I have purchased a WAP54G, but I forsee the same problems when I go to config everything tomorrow.
I have a WET610 that I intend to use to connect a PC to the local network and further on to the Internet. The local connection works, I can ping to and from the computer connected to the WET610 and I can see the other computers, both wired and wireless, on the network so the wireless connection is ok but I can't connect to the Internet, I can't even ping the DNS I'm using. What can be wrong? All the other computers can access the Internet. The WET610 talks to a wireless AP which in turn is connected to a router
I just now installed a new EA4500 Router. It installed itself automatically without a problem, by running the setup CD. No devices other than my hard wired computer and modem are connected yet.
When I went into Start > Cisco Connect to look around and check it's version, etc., I immediately got a "There's an important update for your router" notice. My concern is not wanting to install The Cloud at this time (although I wouldn't rule it out later). There has not been a trace of it so far.
I currently have Firmware Version: 2.0.36.126507 and Software Version: 1.4.12100.0. What this Important Update may be? Is it the "dreaded" Cloud? I'd rather avoid the whole rolling back to pre-Cloud issue for now, if possible.
I just bought this used WAP54G, trying to link it to my home WLAN network, using my WRT54GS. I was able to get into to it, and change the configurations to match my network. But I still can't get access to it via wireless? I can still get back in via wired. How do I know(or not know) that the wireless part of this box works?
We have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.
-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?
I've moved into a new apartment with a couple of people who already have wifi set up. They are adament about me not running a ethernet cable across the apartment to my room for my xbox 360. I have a DIR-601 from my last apartment, and I am wondering if there is a way to set up the router as an access point that allows me to connect to the existing wifi network and then wire my xbox 360 in.
When the WAP54G is set up as a repeater for a WRT54G, will a computer connected to the LAN port on the WAP54G be able to connect to the network? I know it will see the WAP54G if I manually set it's ip address.
I guess I want it to act as a wireless NIC for the desktop while also operating as a repeater. Is this possible? If not, will one of the other AP settings like Bridge allow the wired connection to connect to the other side of the network and give wireless access to wireless devices? I've hacked up and attached one of Linksys's diagrams to show what I'm trying to do. It seems to me the easiest thing to do would be to buy a wireless NIC for the desktop.
There are 2 XBox's in the house and 1 is downstairs wired into the WRT320N Router. The upstairs XBox is running wirelessly through the router. Each of the XBox's work fine playing Modern Warfare 3, when only one is playing, but if both of us are playing, the wired connection works great, while the wireless connection is really slow and laggy. Again, the wireless XBox runs fine as long as the wired XBox isn't also playing MW3.
we have two desktop Pc's both hard wired to a Linksys router. One P.C is on Windows 7 system the other is on Vista. The windows 7 is connecting O.K. The one on Vista is showing " Does not have a wireless network adaptor, install & configure. The Vista P.C. was working O.K. a couple of days ago.Also not connecting to a laptop from the host computer on the Vista system?
My problem is that my son will not turn off his xbox at night. To get around this I want to connect the Xbox to an old netgear router that I am using as an access point to extend wireless coverage, so that I can use the parental controls on the netgear as the ones in the Sky Sagem are not adequate.I can disconnect the Netgear at a certain time if necessary and if this is the only way the xbox can connect it will have to go offline then!
DGL-4100 (wired gigabit router) -> Wii -> X360 -> PS3 -> DGS-2205 (wired gigabit switch in study) *-> My PC *-> Her PC *-> DAP-1522 (wireless access point/bridge)
Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.
I have RV082 in many locations and it is working fine.One location I just starting to have problem with packet lose (50 to 60 %)I ping between two location which i am having problem.Gateway to Gateway shows no lose on packet (reply with 20ms avg.)but router to router will lose packet 50 to 60 %.
I have a DSL modem, model AG10W. I can't seem to figure out how to forward ports to xbox. No one seems to have this router/modem. I got it from a company here in town. I don't know much about this type of stuff.
I have my router setup fine to the internet, as well as the media server. I can't figure out how to access the hard drive from my laptop, however. The manual says put 192.168.1.1 in the address field of windows explorer, but it just gives me the "Setup" page for the router.
I have been having some issues connecting my PC to my XBox360 using the wired approach, it seems to be massively temperamental to a point i decided to not connect the XBox via my router and instead put it straight into my spare network port on my PC. The basic jist of mynetwork confirguration is something like this: Internet cable > Virgin Media 256 Modem > Linksys BEFSR41 Router > PC. I had no issues with this setup, but as soon as i wanted to add my XBox into the mix, things got tricky. I plugged the network cable from my Xbox originally into one of the ports on my router and then went through the settings on both my Xbox and router. Again, i had absolutely no confidence in doing this myself since i don't mess with it, but after reading guides i finally got it sorted. Well, partly sorted. I was able to connect to my Xbox Live, however i was unable to connect to my Xbox to my PC (To stream files onto the Xbox). This was what i wanted to do, i didn't really want to use the Live anyway. So i went off to work again. In the end nothing was working, so i opted to connect my Xbox directly into my PC - So it was no longer connected through my router. I could SEE my PC on my Xbox, but i was unable to connect to it to stream anything. I then opted to disconnect my router (For no other reason than to rule it out) - Sure enough, the very second i disconnected the router, i was able to instantly connect to my PC and was streaming straight away. Once i was streaming, i was able to reconnect my router and that was that. But if i turned off my Xbox i would need to also turn off my router the next time i wanted to stream. How can i fix this so i don't have to continually turn off my router, is there a setting somewhere in the options on my router which can allow me to connect to my Xbox? Windows 7 Xbox 360 Linksys BEFSR41 - 2.00.02 Firmware
I just purchased a Linksys e4200 router today along with a WD 2TB MyBook hard drive. My intent is to set these two up together so that i can share files on the hard drive with: Computers on my home network ( 1 Windows 7 desktop wired, 1 windows 7 laptop wifi, 1 XP netbook wifi)Computers remotely over the internetSmartphones (Android and Apple) on my home networkSmartphones (Android and Apple) remotely over the internet. My questions are: Set-up remote access for fileshare with smartphones?What is the easiest way to set-up and configure this?
I had previously posted about problems with the E1550 not being able to recognize NTFS formated hard drives. After multiple retries and reformats I was finally able to get it to work and was able to backup my system files to that NTFS hard drive.
Now, little more than a week later I setup to run my backup to run again and once again the E1550 is not accessing the hard drive. The same one it had previously acknowledged and allowed me to save to.
The E1550 sees that there is a hard drive out there but all it says is "Detecting..." this does not change.
I need this to be fixed and stay fixed. If it is going to do this every time I turn on the drive to do weekly backups, then I need to get a different wireless router.
WD essential 2GB hard drive connects OK through cisco connect but when I click on the shortcut or try to access the drive I get access denied duer to permission to the ip address
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine! The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
