Can Connect To Access Point Using Both Wired And Wireless Medium
Feb 17, 2013Can connect to access point using both wired and wireless medium
View 1 Replies
ADVERTISEMENT
Connect Old Linksys Router As A Wired (and Maybe Wireless) Access Point
Oct 12, 20111. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
Build A Medium Network And Connect It To The Internet?
Dec 26, 2011I need to build a medium network and connect it to the internet MORE DETALIS; what are the hardware requiremnet i need to build this network?? i need to monitor and control every thing in this network. it should be like this(one ADSL line with high speed connection coming from my ISP-(internet service provider)++ a room to put all the equipment and decives use in the network=routers,modem,servers,cables and so on= ++ then from this room or place i divide the one line coming to sub-netwrks--in my case about 6 subnetworks-- then spread all the cables and so on, to each department or division
View 7 Replies View RelatedDAP-1522 / Adding Wireless Access Point To Wired Network?
Dec 27, 2010Here's the setup:
DGL-4100 (wired gigabit router)
-> Wii
-> X360
-> PS3
-> DGS-2205 (wired gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522 (wireless access point/bridge)
Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.
Linksys Access Point :: WET610N Shows Hard Wired Not Wireless With Xbox 36
Dec 27, 2012I have an E4200 router with 3 WET610N access points. I did the firmware update on the router, E4200, about 2 weeks ago so my son could use his xbox when he got home after 4 months of being away. Everything seemed to work OK as far as I could tell....but when he went to sign into xbox live and watch Netflix, it will load to 98% and stop. A friend of his came over with the new Slim xbox 360 with built in wireless and it will connect fine on its own, if we hook up one of the 610N's to it, it will load to 98% on Netflix and stop again with error code R8152. Both of my older xbox's will hook up and play on xbox live, just not work with Netflix.I also noticed, it shows the WET610N as a hard wire on xbox and will not search for any wireless networks, I have 2. The newer Slim xbox360 will search out both networks on its own if you allow it to use its internal wireless. This only happened since the firmware update.
View 3 Replies View RelatedLinksys Access Point :: WAP54G - Can't See Wired Network Devices With Wireless Connection
Mar 3, 2011I work at a small business that has an exisiting wired network. Our setup is: Internet > ISP Box > DHCP Server > Switch > Users. I have been attempting to add a wireless router to the network to enable our shop techs to wirelessly access our file computer. I have managed to get the wireless working, but the network was not visible, I could not access any network computers from the wireless, and I could not access the wireless router from our main server. After this I screwed up the settings completely and even a wired connection to the router couldn't connect to the internet. Now I have purchased a WAP54G, but I forsee the same problems when I go to config everything tomorrow.
View 2 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?
Apr 25, 2011I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
Linksys Access Point :: WRT120N - Cannot Connect To An Access Point
May 10, 2013I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Linksys Access Point :: WAP54G Only Connects Via Wired?
Jul 29, 2011I just bought this used WAP54G, trying to link it to my home WLAN network, using my WRT54GS. I was able to get into to it, and change the configurations to match my network. But I still can't get access to it via wireless? I can still get back in via wired. How do I know(or not know) that the wireless part of this box works?
View 2 Replies View RelatedLinksys Wired Router :: Rv042 / Wifi Access Point On Dmz
Apr 4, 2011We have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.
-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?
Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedLinksys Access Point :: WAP54G LAN Port Support Wired Computer Connection
Jul 7, 2011When the WAP54G is set up as a repeater for a WRT54G, will a computer connected to the LAN port on the WAP54G be able to connect to the network? I know it will see the WAP54G if I manually set it's ip address.
I guess I want it to act as a wireless NIC for the desktop while also operating as a repeater. Is this possible? If not, will one of the other AP settings like Bridge allow the wired connection to connect to the other side of the network and give wireless access to wireless devices? I've hacked up and attached one of Linksys's diagrams to show what I'm trying to do. It seems to me the easiest thing to do would be to buy a wireless NIC for the desktop.
Cisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedWireless :: Connect Two Edimax Access Point On Same Net?
Apr 18, 2012Tried to connect a second Edimax AP to my home network configured as repeater. Keep getting random errors. Each of them have a different IP address
View 11 Replies View RelatedConnect Wireless Access Point To Switch
Jun 22, 2011How can i configure my wireless AP to provide wireless internet to my network via my switch?
View 2 Replies View RelatedCannot Connect More Than One Computer To Wireless Access Point?
Jan 17, 2011I recently switched from DSL to cable. No issues on DSL. Since switching to cable, I haven't been able to connect more than one computer to the wireless access point at one time. I have three computers, one running W7, one on xp, and one on Vista. All three of the computers have been able to connect to the WAP when connecting alone.I am using a wap54g linksys access point. Setup is internet --> coax --> cable modem --> ethernet --> wap[CODE]
View 2 Replies View RelatedCisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point
Apr 20, 2012I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedConnect 2 Wireless Access Point As Same Time To One Laptop
Mar 22, 2012is it possible to connect 2 wireless access point as same time to one laptop.
View 2 Replies View RelatedConnect Wireless Access Point Router To The Internet?
Dec 26, 2012How do I connect my wireless access point router to the internet so that I may use my ipad?
View 2 Replies View RelatedConnect Two Laptops To The Internet Via One Wireless Access Point?
Jul 4, 2011At home I have a wireless access point that I use to connect my laptop #1 to the Internet. On laptop #1 IP address is set to 193.49.21.65. This IP address also Subnet Mask and other addresses are given by my Internet Service Provider. Everything works just fine but lately I bought another laptop (laptop #2) and now my aim is to connect both laptops to the Internet. Unfortunately, I can't make that happen. Only one of my laptops having IP 193.49.21.65 set can connect to the Internet.
[URL]
So is there any way to have an Internet connection on both of my laptops without having to buy any new equipment?
Connect A Wireless Access Point (a Tenda W311r+) Wirelessly?
Apr 13, 2012I am trying to setup my network in my home, so that I can extend the wireless signal from my main router by using an access point (a tenda w311r+).But, I want to do it so that the access point isn't connected to the main router with a cable, I want it to be connected to the main router wirelessly.It does say on the box that it can 'bridge' multiple wireless routers.
The access point I have also has 4 ethernet ports on it, so I will use one of these to plug my xbox 360 into.I also want the main router to be responsible for the DHCP.
Routers / Switches :: How To Connect Router And Wireless Access Point
Mar 13, 2011I have high-speed cable access currently coming into an older D-Link 4-port wired router. I need to buy a new wired and wireless router so I can sync my new Android 4G phone (I'm in an area with bad cell coverage but I can sync with wi-fi). I have a second house about 200 feet from mine and have 3 Cat5E lines running underground in conduit to it so the lady next door and and her two kids can use the internet (I have 40-50mb service for my business use at home). Problem is that my kids have discovered YouTube, streaming video, video chat, etc. and are burning up my bandwidth. I currently have two of the lines to them disconnected so that I can limit their use to one computer at a time. I'm considering having them buy a Wireless Access Point, can they connect it to the standard single Cat5E LAN wire that is coming from my new wired and wireless router when I buy it?
View 2 Replies View RelatedConnect Android Phone To Wireless Access Point Laptop?
Sep 4, 2012I setup an accespoint on my laptop. Now I want to connect my Phone (android) to this network but, he is asking for an Ip-address I tried the following;
- give the phone a static ip address
D-Link DIR-655 :: Using As Wireless Repeater / Access Point / Bridge To Connect
Apr 12, 2011I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies View RelatedLinksys Wireless Router :: Befw11s4v4 To Connect Access Point
Nov 13, 2011I have a Verizon Actiontec M1424-WR router that is my main router for internet access. I would like to use my Linksys Broadband Router BEFW11S4 Wireless-B as an access point in my garage so that I can connect non-wireless (wired) computers to it. I've tried different configurations but no success; I've read alot about connecting the routers together through an ethernet cable but I want to connect them wirelessly.
View 1 Replies View RelatedD-Link DSL-2750U - Connect Wireless Access Point To Modem
Jul 7, 2013At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.
View 1 Replies View RelatedLinksys Wireless Router :: WRT54g Can't Get Devices To Connect To Access Point
Oct 22, 2011I have a WRT54g with Tomato firmware. I am trying to set up a WAP54g to extend the range but while that access point does show up as a network, nothing can connect to it. I already have the router's MAC address put in the WAP. I think the problem is that I have Tomato on the router and that conflicts with the default firmware on the WAP. Range isn't really the problem, I just need to strengthen the signal in a specific area that it's not getting to because of walls. I can't even switch to previous versions of Tomato anymore. I may have just bricked it.Some facts about my setup-My modem has default settings: PPPoE connection with a DHCP server enabled.-I set the router to use DHCP and put it in "Access Point" mode.
-The WAP is set to repeater mode and it was set to Static IP configuration by default. I simply followed the instructsions here: url....
-There are three different MAC addresses: The WAN, LAN/router, and the Wireless. I put the Wireless MAC address in the access point. Is that correct?
-My desktop is wired directly to the router and it has a static IP outside the router DHCP's IP range-UPnP is enabled by default in the modem and router, but I'd like to try to get this working rather than buy all new equipment.
Cisco Wireless :: How To Connect Macbook Air With 1100 Series Access Point
Oct 10, 2011how to connect macbook air with cisco 1100 series access point
View 2 Replies View RelatedLinksys Wireless Router :: E2500 As An Additional Access Point Will Not Connect
Oct 16, 2012I have AT&T Uverse which provides Internet for my home. The wireless capability of this router is pretty bad, I don't get good/reliable wireless reception upstairs in my office. The solution was to buy a Cisco E2500 and add it as an access point upstairs.
I have the E2500 LAN port connected to the LAN port of my uverse router downstairs. DHCP is turned off on the E2500. I have my office PC wired into the E2500. The home PC works fine, its getting DHCP from the uverse router downstairs and connects and good speeds. The problem comes with my wireless devices trying to connect to the E2500.
I should mention that yesterday when i bought this, all worked fine. This morning when I came into my office none of the wireless devices would connect to the E2500 at all. But as soon as I remove the cable that connects the E2500 to the uverse router downstairs they will connect via wireless but of course not get an IP address since that is disabled.
I have factory reset the E2500 and uverse router several times and am getting no where. what could be causing the wireless devices to not connect at all?
Dell Inspiron 1520 Suddenly Will Not Connect To Access Point / Wireless Router / DSL
Dec 15, 2012Dell Inspiron 1520 Windows XP SP 3?My Dell suddenly will not connect to access point / wireless router / DSL. Other computer in house connects fine. Computer is auto-updated by Windows, McAfee, Secunia, and frequently checked with System Mechanic, McAfee, Lavasoft, MalwareBytes. One of the auto updates may have been interrrupted.Says Wireless adapter "not present"...Does not recognize wireless in the area. Try to "repair" adapter, but message says adapter not present.I then use System Restore to 4 day earlier date and laptop connects immediately. I see a new symbol "Local Area connection on Actiontec m1000 has been added in the Network Connection window, and the Wireless Network Connection says it is connected to the correct network that has worked fine for several years.I have several Windows updates for the Malware Tool that install immediately if I reboot, but then I cannot connect to the network and have to use System Restore (which is taking longer and longer to restore...appx 1.5 hrs now).
View 6 Replies View RelatedCisco Wireless :: Aironet 1140s - How To Connect Repeater To Specific Access Point
Feb 12, 2013In our office, we have 3 Cisco Aironet 1140s and they are configured as follows:
* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
how to have the Repeater connect to Access Point A only?
Cisco Wireless :: Can Access Point AP541N Connect To Wireless Clients
Aug 10, 2010Can the access point AP541N connect to wireless clients with 802.11g/a simultaneously?
View 1 Replies View Related