Am trying to connect 3 pcs connected to a Dlink 8 port switch through a Dlink WL2100 Access point connected as an AP Client to the main network. Only 1 pc is able to see the main network and am having none of the other 2pcs are able to see the main network. The 3 pcs are able to see each other.
i am trying to configure my HP 420 access point. I have configure different SSID on it, This access point is connected to cisco 4500 switch, i have configure trunk on up link to access point.my problem is the client are not able to get an IP address form the correct vlan if i tagged the SSID to it.
in the following the output of show run int in cisco 4500 switch:
interface GigabitEthernet3/13 description ==== HP ACCess point ==== switchport trunk allowed vlan 99,130,132 switchport mode trunk
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
I am having a problem setting up an Access Point. Here is my configuration. I have a Comcast Cable Modem that plugs in to a 24 port Netgear Switch. From the switch it plugs into a Linksys N wireless router with an IP of 10.1.10.76. I don't know the linksys model. But it is fairly new. I also have a Netgear WN604 N Access Point that plugs in to the same switch in another location away from the wireless router about 75+ft.
I configured the access point's IP to be 10.1.10.130 with DHCP off and DNS as 10.1.10.1. The cable modems default Gateway is 10.1.10.1 and it handles the dhcp which is provided to the switch were both the wireless router and access point get there IP's. I can't set it up so that the cable modem plugs in to the wireless router first then the switch because of a security system that is setup to the Comcast Cable Modem.
My Goal is to the the same identical SSID and Password for both the Linksys and Access point. I don't think I can set it up as a repeater because it's to far away from the linksys router.
I am staying with some family for the next two months and they don't have wireless internet at their house. When they bought their house it was wired for ethernet and have the modem going to a netgear 8 port switch which is going to the different rooms of the house. I would like to add a wireless access point to one of those 8 ports coming from the switch. I currently have a TP-LINK TLWR740N router that I can configure into an access point, or I can buy just and access point. Unfortunately it is not an option for me to plug the modem into the router and then the router into the switch.
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine! The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
192.168.1.1 is a Linksys WRT610N acting as a router and DHCP server for addresses .100 to .150 192.168.1.2 is TEW-639 with DHCP turned off and connected to the Lynksys via one of the LAN ports.
I then have a FosCam camera with IP 192.168.1.010, connected either wirelessly or via a wire on a LAN port to the TEW-639W.
Here is my problem: If the FosCam is connected wirelessly to the TEW-639W I am unable to see it from any device connected to the Linksys. If I connect the FosCam via a wire to a LAN port on the TEW-639W then I can see it from a device connected to the Linksys device.If a device is connected to the network via the TEW-639, I can see the FosCam whether it is hardwired or wirelessly connected to the TEW-639. What am I doing wrong?Why can I not see the wireless connections on the TEW-639 from a Linksys connected device?,The setup is that the internet comes in and is connected to the Linksys, which then via LAN cable and LAN ports on both devices is connected to the TEW-639, which is then connected to the camera.
we got a At&T Modem/Router upstairs, and then we got a long ethernet cable running from there to the basement. The problem is that this only allows for one LAN connection at a time (an issue for LAN parties and such). I do have an E2000 Linksys router however and I want to be able to use that as like a switch/access point.I am pretty sure this is possible but I have forgotten all of the steps to do it.The att modem/router is running on 192.168.1.254, and my Linksys which is now directly connected is on 192.168.1.1, so I have a different address in that regards.Do I need to edit my Linksys settings now, or do I have to edit the at&t settings?Also I will be using this for Xbox Live at points so will I need to re-open all those ports up on my Linksys, or at least set the DHCP to the Xbox's static IP to keep my NAT good?
i have 2 cisco 1522 series out door LAP connected to a 3560 POE switch which is not powering up, while ordering my dealer told that it will work with POE, and its go live stage, is there any way to upgrade switch with any IOS version where i can get enough power for 1522?
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
I recently switched from DSL to cable. No issues on DSL. Since switching to cable, I haven't been able to connect more than one computer to the wireless access point at one time. I have three computers, one running W7, one on xp, and one on Vista. All three of the computers have been able to connect to the WAP when connecting alone.I am using a wap54g linksys access point. Setup is internet --> coax --> cable modem --> ethernet --> wap[CODE]
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
At home I have a wireless access point that I use to connect my laptop #1 to the Internet. On laptop #1 IP address is set to 220.127.116.11. This IP address also Subnet Mask and other addresses are given by my Internet Service Provider. Everything works just fine but lately I bought another laptop (laptop #2) and now my aim is to connect both laptops to the Internet. Unfortunately, I can't make that happen. Only one of my laptops having IP 18.104.22.168 set can connect to the Internet.
So is there any way to have an Internet connection on both of my laptops without having to buy any new equipment?
I think I know what I want, but I just wanted to check before I splashed the cash and made the wrong choiceI have a Humax Freesat recorder and a Panasonic Blu-Ray player. Both of which have services that need internet access, but neither are WIFI enabled & are the wrong side of the room to be connected via cabled ethernet.I believe that what I need is to wireless access point? I'd like one with a built in switch as well, as most seem to only come with only one port. The one I found has four, which would be useful as I could replace the poor wireless Xbox 360 dongle.
I am trying to setup my network in my home, so that I can extend the wireless signal from my main router by using an access point (a tenda w311r+).But, I want to do it so that the access point isn't connected to the main router with a cable, I want it to be connected to the main router wirelessly.It does say on the box that it can 'bridge' multiple wireless routers.
The access point I have also has 4 ethernet ports on it, so I will use one of these to plug my xbox 360 into.I also want the main router to be responsible for the DHCP.
I have high-speed cable access currently coming into an older D-Link 4-port wired router. I need to buy a new wired and wireless router so I can sync my new Android 4G phone (I'm in an area with bad cell coverage but I can sync with wi-fi). I have a second house about 200 feet from mine and have 3 Cat5E lines running underground in conduit to it so the lady next door and and her two kids can use the internet (I have 40-50mb service for my business use at home). Problem is that my kids have discovered YouTube, streaming video, video chat, etc. and are burning up my bandwidth. I currently have two of the lines to them disconnected so that I can limit their use to one computer at a time. I'm considering having them buy a Wireless Access Point, can they connect it to the standard single Cat5E LAN wire that is coming from my new wired and wireless router when I buy it?
1. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
I have a Verizon Actiontec M1424-WR router that is my main router for internet access. I would like to use my Linksys Broadband Router BEFW11S4 Wireless-B as an access point in my garage so that I can connect non-wireless (wired) computers to it. I've tried different configurations but no success; I've read alot about connecting the routers together through an ethernet cable but I want to connect them wirelessly.
At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.
I'm using 4 wap200 cisco AP, 1 wap200e linksys AP and 1 cisco sf300-24p switch. Every AP has 2 SSIDs,one is for clients and one for mobile devices.I have updated the equipment to the latest firmware but I still encounter the same issue. The mobile devices go through APs and once every 2 days, my wap200e blocks its lan interface. I suspected a stp issue, because the switch was seeing MAC addresses coming from different ports.So I disabled STP on the switch and on the AP. The annoying thing thing is that none of my other antennas get cut off.I tried replacing it with a cisco wap200e,same issue.
I have a Cisco 2811 router with C288nm-advsecuruityk9-mz.151-4-4.M.bin IOS version.The router has two LAN interface FE 0/0 and FE 0/1.The router have too, two interfaces ADSL ATM0.0.0 and ATM 0.0.1, both are connect to internet..I need the next configuration.The interface FE 0/0 is directly connect to a Switch A.The interface FE 0/1 is directly connect to a Access Point Cisco.The Access Point and the Switch is not connecting between.The subnet of Switch A and AP are different (Switch A 192.168.180.0/24 and AP 192.168.181.0/24)The devices in the switch A have dynamic IP address, the router must be a DHCP pool to assign theses IP.The device in the AP have dynamic IP address, the router must be a DHCP pool to assign theses IP.I created two DHCP pools in the router, one for the subnet 192.168.180.0 and other for 192.168.181.0, but the devices of FE 0/0 assign IP of 192.168.180.0 or 192.168.181. 0, but not only in the 192.168.180.0.
I have a WRT54g with Tomato firmware. I am trying to set up a WAP54g to extend the range but while that access point does show up as a network, nothing can connect to it. I already have the router's MAC address put in the WAP. I think the problem is that I have Tomato on the router and that conflicts with the default firmware on the WAP. Range isn't really the problem, I just need to strengthen the signal in a specific area that it's not getting to because of walls. I can't even switch to previous versions of Tomato anymore. I may have just bricked it.Some facts about my setup-My modem has default settings: PPPoE connection with a DHCP server enabled.-I set the router to use DHCP and put it in "Access Point" mode.
-The WAP is set to repeater mode and it was set to Static IP configuration by default. I simply followed the instructsions here: url....
-There are three different MAC addresses: The WAN, LAN/router, and the Wireless. I put the Wireless MAC address in the access point. Is that correct?
-My desktop is wired directly to the router and it has a static IP outside the router DHCP's IP range-UPnP is enabled by default in the modem and router, but I'd like to try to get this working rather than buy all new equipment.