Connect Wireless Access Point Router To The Internet?
Dec 26, 2012How do I connect my wireless access point router to the internet so that I may use my ipad?
View 2 Replies
ADVERTISEMENT
Connect Two Laptops To The Internet Via One Wireless Access Point?
Jul 4, 2011At home I have a wireless access point that I use to connect my laptop #1 to the Internet. On laptop #1 IP address is set to 193.49.21.65. This IP address also Subnet Mask and other addresses are given by my Internet Service Provider. Everything works just fine but lately I bought another laptop (laptop #2) and now my aim is to connect both laptops to the Internet. Unfortunately, I can't make that happen. Only one of my laptops having IP 193.49.21.65 set can connect to the Internet.
[URL]
So is there any way to have an Internet connection on both of my laptops without having to buy any new equipment?
Routers / Switches :: How To Connect Router And Wireless Access Point
Mar 13, 2011I have high-speed cable access currently coming into an older D-Link 4-port wired router. I need to buy a new wired and wireless router so I can sync my new Android 4G phone (I'm in an area with bad cell coverage but I can sync with wi-fi). I have a second house about 200 feet from mine and have 3 Cat5E lines running underground in conduit to it so the lady next door and and her two kids can use the internet (I have 40-50mb service for my business use at home). Problem is that my kids have discovered YouTube, streaming video, video chat, etc. and are burning up my bandwidth. I currently have two of the lines to them disconnected so that I can limit their use to one computer at a time. I'm considering having them buy a Wireless Access Point, can they connect it to the standard single Cat5E LAN wire that is coming from my new wired and wireless router when I buy it?
View 2 Replies View RelatedConnect Old Linksys Router As A Wired (and Maybe Wireless) Access Point
Oct 12, 20111. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
Linksys Wireless Router :: Befw11s4v4 To Connect Access Point
Nov 13, 2011I have a Verizon Actiontec M1424-WR router that is my main router for internet access. I would like to use my Linksys Broadband Router BEFW11S4 Wireless-B as an access point in my garage so that I can connect non-wireless (wired) computers to it. I've tried different configurations but no success; I've read alot about connecting the routers together through an ethernet cable but I want to connect them wirelessly.
View 1 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedHow To Connect Two Access Point Switches With Internet
Sep 22, 2012How we connect two different access point to each other
View 1 Replies View RelatedPc Connect To Internet Through Mobile Access Point?
Sep 28, 2012I want to use my PC for internet access in my office (shed)Shed does not have phone line or cable points.PC does not have wireless capability.Moile phone can be used as Access Point (but PC can't detect it- no wireless capability)What is the methods to provide plug-in/ bolt-on wireless capability for my PC so that it can use my mobile Access Point to connect to the internet?
View 2 Replies View RelatedLinksys Wireless Router :: WRT54g Can't Get Devices To Connect To Access Point
Oct 22, 2011I have a WRT54g with Tomato firmware. I am trying to set up a WAP54g to extend the range but while that access point does show up as a network, nothing can connect to it. I already have the router's MAC address put in the WAP. I think the problem is that I have Tomato on the router and that conflicts with the default firmware on the WAP. Range isn't really the problem, I just need to strengthen the signal in a specific area that it's not getting to because of walls. I can't even switch to previous versions of Tomato anymore. I may have just bricked it.Some facts about my setup-My modem has default settings: PPPoE connection with a DHCP server enabled.-I set the router to use DHCP and put it in "Access Point" mode.
-The WAP is set to repeater mode and it was set to Static IP configuration by default. I simply followed the instructsions here: url....
-There are three different MAC addresses: The WAN, LAN/router, and the Wireless. I put the Wireless MAC address in the access point. Is that correct?
-My desktop is wired directly to the router and it has a static IP outside the router DHCP's IP range-UPnP is enabled by default in the modem and router, but I'd like to try to get this working rather than buy all new equipment.
Linksys Wireless Router :: E2500 As An Additional Access Point Will Not Connect
Oct 16, 2012I have AT&T Uverse which provides Internet for my home. The wireless capability of this router is pretty bad, I don't get good/reliable wireless reception upstairs in my office. The solution was to buy a Cisco E2500 and add it as an access point upstairs.
I have the E2500 LAN port connected to the LAN port of my uverse router downstairs. DHCP is turned off on the E2500. I have my office PC wired into the E2500. The home PC works fine, its getting DHCP from the uverse router downstairs and connects and good speeds. The problem comes with my wireless devices trying to connect to the E2500.
I should mention that yesterday when i bought this, all worked fine. This morning when I came into my office none of the wireless devices would connect to the E2500 at all. But as soon as I remove the cable that connects the E2500 to the uverse router downstairs they will connect via wireless but of course not get an IP address since that is disabled.
I have factory reset the E2500 and uverse router several times and am getting no where. what could be causing the wireless devices to not connect at all?
Dell Inspiron 1520 Suddenly Will Not Connect To Access Point / Wireless Router / DSL
Dec 15, 2012Dell Inspiron 1520 Windows XP SP 3?My Dell suddenly will not connect to access point / wireless router / DSL. Other computer in house connects fine. Computer is auto-updated by Windows, McAfee, Secunia, and frequently checked with System Mechanic, McAfee, Lavasoft, MalwareBytes. One of the auto updates may have been interrrupted.Says Wireless adapter "not present"...Does not recognize wireless in the area. Try to "repair" adapter, but message says adapter not present.I then use System Restore to 4 day earlier date and laptop connects immediately. I see a new symbol "Local Area connection on Actiontec m1000 has been added in the Network Connection window, and the Wireless Network Connection says it is connected to the correct network that has worked fine for several years.I have several Windows updates for the Malware Tool that install immediately if I reboot, but then I cannot connect to the network and have to use System Restore (which is taking longer and longer to restore...appx 1.5 hrs now).
View 6 Replies View RelatedLinksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?
Apr 25, 2011I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
Linksys Wireless Router :: Connect To EA6500 In Bridge Mode Acting As Access Point?
Mar 4, 2013How do I connect to the EA6500 once it's in Bridge mode acting as a wireless access point? Checked the posts and some seem to be able to do this but, we cannot.
View 6 Replies View RelatedLinksys Access Point :: WAP4410N - Internet Connection Always Connect And Disconnect
Aug 18, 2011I have a new notebook Sony Z217GG, I connected WAP 4400N was very smooth, but after connected WAP 4410N, the internet connecting always connect and disconnect, I check the notebook wireless model is intel 6230.
View 1 Replies View RelatedLinksys Access Point :: WRT120N - Cannot Connect To An Access Point
May 10, 2013I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Connect A Router To An Access Point?
Dec 9, 2011I currently have a network setup like this:
Route 1 --> Switch --> Access Points ---> Router2 connected to one of the access point
So pretty much I'm trying to create a wireless network for a temple. I set up a network with several access points as above. However, they wanted a network for the office separate from the rest of the temple. So I decided to setup Router2 and connect it to one of the LAN ports of an access point.
However, this seems messing up the whole network. People can connect to the access points but they won't have access to the Internet. Also, if I connect my laptop to the office network, I wouldn't see the gateway as 192.168.1.1, which was set for Router2. Instead, I always saw the IP address of Router1 as the gateway.
How To Connect A Router To Access Point
May 7, 2012How to connect a router to access point
View 1 Replies View RelatedCisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCisco Wireless :: 2960 - Autonomous Access Point / Get Guest To Access Internet?
May 9, 2012I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
Cisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedConnect Xbox To 2nd Router / Access Point Using Powerline Plugs
Aug 16, 2012My problem is that my son will not turn off his xbox at night. To get around this I want to connect the Xbox to an old netgear router that I am using as an access point to extend wireless coverage, so that I can use the parental controls on the netgear as the ones in the Sky Sagem are not adequate.I can disconnect the Netgear at a certain time if necessary and if this is the only way the xbox can connect it will have to go offline then!
View 4 Replies View RelatedWireless :: Connect Two Edimax Access Point On Same Net?
Apr 18, 2012Tried to connect a second Edimax AP to my home network configured as repeater. Keep getting random errors. Each of them have a different IP address
View 11 Replies View RelatedConnect Wireless Access Point To Switch
Jun 22, 2011How can i configure my wireless AP to provide wireless internet to my network via my switch?
View 2 Replies View RelatedCannot Connect More Than One Computer To Wireless Access Point?
Jan 17, 2011I recently switched from DSL to cable. No issues on DSL. Since switching to cable, I haven't been able to connect more than one computer to the wireless access point at one time. I have three computers, one running W7, one on xp, and one on Vista. All three of the computers have been able to connect to the WAP when connecting alone.I am using a wap54g linksys access point. Setup is internet --> coax --> cable modem --> ethernet --> wap[CODE]
View 2 Replies View RelatedCisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point
Apr 20, 2012I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedConnect 2 Wireless Access Point As Same Time To One Laptop
Mar 22, 2012is it possible to connect 2 wireless access point as same time to one laptop.
View 2 Replies View RelatedCan Connect To Access Point Using Both Wired And Wireless Medium
Feb 17, 2013Can connect to access point using both wired and wireless medium
View 1 Replies View RelatedConnection Between Access Point / Router / Or Cable Modem And The Internet Is Broken?
Aug 26, 2012The detected problem is the connection between my access point, router, or cable modem and the Internet is broken.The network gateway is accessible, but Windows couldn't receive network traffic from the Internet.All other devices (iPad, Xbox, android phone) have no problem connecting to the Internet.Desktop is the only one experiencing the connection issue.
View 1 Replies View RelatedConnection Between Access Point / Router Or Cable Modem - Internet Broken
Jan 31, 2012My laptop died last week and have been using my husbands, which I hate! We had some issues with computer freezing on some webpages or after being on webpages for awhile (like facebook). Yesterday it froze and I could not get it back on. When he got home he did scan disk (which I also did) and got it working after going into safe mode and doing system restore. He said an update had gotten through and messed things up. Anyhow, after he was on it a few hours last night, we lost connection. I figured the crazy weather was the culprit but it has been off all day. Our router is working and connecting but the adapter is not. Also our home phone says there is no line. We have unplugged everything several times, checked to make sure everything is in the right spots, I have even reset the router and rebooted the adapter. I uninstalled and restalled the adapter also. It is now telling me that "the connection between your access point, router, or cable modem and the Internet is broken". The only lights I have on the adapter are power, battery, DS and now the US light is blinking. The online and link lights are not on.
View 3 Replies View RelatedLinksys Access Point :: Connect WRT54GL Router To Repeater To Establish WLAN Bridgde
Aug 27, 2012I got an Fritz Box from my new Provider to connect to the internet using Fiber To Home. the box is now im my living room and also acts as an WLAN Router. I would like to configure my WRT54GL which in located in my office from a router to a repeater to establish a WLAN bridgde.
View 3 Replies View RelatedConnect A Wireless Access Point (a Tenda W311r+) Wirelessly?
Apr 13, 2012I am trying to setup my network in my home, so that I can extend the wireless signal from my main router by using an access point (a tenda w311r+).But, I want to do it so that the access point isn't connected to the main router with a cable, I want it to be connected to the main router wirelessly.It does say on the box that it can 'bridge' multiple wireless routers.
The access point I have also has 4 ethernet ports on it, so I will use one of these to plug my xbox 360 into.I also want the main router to be responsible for the DHCP.
Connect Android Phone To Wireless Access Point Laptop?
Sep 4, 2012I setup an accespoint on my laptop. Now I want to connect my Phone (android) to this network but, he is asking for an Ip-address I tried the following;
- give the phone a static ip address
D-Link DIR-655 :: Using As Wireless Repeater / Access Point / Bridge To Connect
Apr 12, 2011I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies View Related