Connect A Wireless Access Point (a Tenda W311r+) Wirelessly?
Apr 13, 2012
I am trying to setup my network in my home, so that I can extend the wireless signal from my main router by using an access point (a tenda w311r+).But, I want to do it so that the access point isn't connected to the main router with a cable, I want it to be connected to the main router wirelessly.It does say on the box that it can 'bridge' multiple wireless routers.
The access point I have also has 4 ethernet ports on it, so I will use one of these to plug my xbox 360 into.I also want the main router to be responsible for the DHCP.
View 3 Replies
ADVERTISEMENT
Feb 8, 2013
i have wimax usb modem and tenda wifi router with rj45 ports.
View 5 Replies
View Related
Dec 30, 2012
I got a new Tenda W311R+ Wireless-N Broadband Router yesterday. I already have a wired broadband internet connection in my home with a Beetel 110TC1 modem. I did following:
1. Connected the Beetel modem to the Tenda router using an Ethernet cable
2. Connected the Tenda router to my PC using another Ethernet cable.
3. Went to 192.168.0.1 (as mentioned in the instructions sheet which came along with the router)
Now, what should I set as the access mode, ADSL Dial-up or DHCP? Are there any other settings I should change in order to enhance the speed? I have Windows XP SP3. Also, do I need my Beetel modem or can I use the router without it?
View 5 Replies
View Related
Dec 12, 2012
How do i have reset my trenda router without a disk?
View 3 Replies
View Related
Aug 20, 2011
can i set up my W311R+ tenda wireless router without the software driver?
View 1 Replies
View Related
May 8, 2012
how do i reset my password for y tenda wireless router w311r
View 1 Replies
View Related
Dec 29, 2012
Tenda router w311r forgot password
View 3 Replies
View Related
Nov 27, 2011
I tried to set up Tenda W311R as a repeater to increase the coverage. I have done the following, but still it cannot get Internet access:Set up WDS with the same channel and use the same encryption as the Linksys router; Disable the DHCP in the W311R;From the wireless point of view, I can see the Tenda router, but no Internet access.
View 3 Replies
View Related
Jul 13, 2011
I am trying to set up a Tenda 150mbps wireless Ap/Router.Im trying to set it up to use it as a range extender.I followed all the directions. I put it in wisp mode. It doesnt seem to be communicating with my Tenda wireless router. It only is showing up as its own connection. so I cant even get on the internet.
View 1 Replies
View Related
Jun 3, 2011
I am trying to wirelessly connect a netgear wgr614 v6 to be used as an accesspoint and my router connected to the cable modem is a dlink dir825
View 1 Replies
View Related
Aug 1, 2012
I have a DVR that I am trying to hook up to my network wirelessly. I have the wireless router in the house and can connect to it with my laptop from the shop in the back. Is there a way I connect the wireless access point to the DVR in the shop and see it on the network in the house?
View 2 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
May 21, 2012
I cannot connect wan using tenda router, lan connection works.
View 1 Replies
View Related
Apr 18, 2012
Tried to connect a second Edimax AP to my home network configured as repeater. Keep getting random errors. Each of them have a different IP address
View 11 Replies
View Related
Jun 22, 2011
How can i configure my wireless AP to provide wireless internet to my network via my switch?
View 2 Replies
View Related
Jan 17, 2011
I recently switched from DSL to cable. No issues on DSL. Since switching to cable, I haven't been able to connect more than one computer to the wireless access point at one time. I have three computers, one running W7, one on xp, and one on Vista. All three of the computers have been able to connect to the WAP when connecting alone.I am using a wap54g linksys access point. Setup is internet --> coax --> cable modem --> ethernet --> wap[CODE]
View 2 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Sep 29, 2011
Iv got tenda router that is connected to the internit but it cannot recognize the othe wan devise type livel one which is connected throgh wire to the wan router?
View 1 Replies
View Related
Mar 22, 2012
is it possible to connect 2 wireless access point as same time to one laptop.
View 2 Replies
View Related
Dec 26, 2012
How do I connect my wireless access point router to the internet so that I may use my ipad?
View 2 Replies
View Related
Feb 17, 2013
Can connect to access point using both wired and wireless medium
View 1 Replies
View Related
Jul 4, 2011
At home I have a wireless access point that I use to connect my laptop #1 to the Internet. On laptop #1 IP address is set to 193.49.21.65. This IP address also Subnet Mask and other addresses are given by my Internet Service Provider. Everything works just fine but lately I bought another laptop (laptop #2) and now my aim is to connect both laptops to the Internet. Unfortunately, I can't make that happen. Only one of my laptops having IP 193.49.21.65 set can connect to the Internet.
[URL]
So is there any way to have an Internet connection on both of my laptops without having to buy any new equipment?
View 1 Replies
View Related
Mar 13, 2011
I have high-speed cable access currently coming into an older D-Link 4-port wired router. I need to buy a new wired and wireless router so I can sync my new Android 4G phone (I'm in an area with bad cell coverage but I can sync with wi-fi). I have a second house about 200 feet from mine and have 3 Cat5E lines running underground in conduit to it so the lady next door and and her two kids can use the internet (I have 40-50mb service for my business use at home). Problem is that my kids have discovered YouTube, streaming video, video chat, etc. and are burning up my bandwidth. I currently have two of the lines to them disconnected so that I can limit their use to one computer at a time. I'm considering having them buy a Wireless Access Point, can they connect it to the standard single Cat5E LAN wire that is coming from my new wired and wireless router when I buy it?
View 2 Replies
View Related
Sep 4, 2012
I setup an accespoint on my laptop. Now I want to connect my Phone (android) to this network but, he is asking for an Ip-address I tried the following;
- give the phone a static ip address
View 2 Replies
View Related
Oct 12, 2011
1. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
View 3 Replies
View Related
Apr 12, 2011
I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies
View Related
Nov 13, 2011
I have a Verizon Actiontec M1424-WR router that is my main router for internet access. I would like to use my Linksys Broadband Router BEFW11S4 Wireless-B as an access point in my garage so that I can connect non-wireless (wired) computers to it. I've tried different configurations but no success; I've read alot about connecting the routers together through an ethernet cable but I want to connect them wirelessly.
View 1 Replies
View Related
Jul 7, 2013
At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.
View 1 Replies
View Related
Oct 22, 2011
I have a WRT54g with Tomato firmware. I am trying to set up a WAP54g to extend the range but while that access point does show up as a network, nothing can connect to it. I already have the router's MAC address put in the WAP. I think the problem is that I have Tomato on the router and that conflicts with the default firmware on the WAP. Range isn't really the problem, I just need to strengthen the signal in a specific area that it's not getting to because of walls. I can't even switch to previous versions of Tomato anymore. I may have just bricked it.Some facts about my setup-My modem has default settings: PPPoE connection with a DHCP server enabled.-I set the router to use DHCP and put it in "Access Point" mode.
-The WAP is set to repeater mode and it was set to Static IP configuration by default. I simply followed the instructsions here: url....
-There are three different MAC addresses: The WAN, LAN/router, and the Wireless. I put the Wireless MAC address in the access point. Is that correct?
-My desktop is wired directly to the router and it has a static IP outside the router DHCP's IP range-UPnP is enabled by default in the modem and router, but I'd like to try to get this working rather than buy all new equipment.
View 7 Replies
View Related
