I am trying to set up a Tenda 150mbps wireless Ap/Router.Im trying to set it up to use it as a range extender.I followed all the directions. I put it in wisp mode. It doesnt seem to be communicating with my Tenda wireless router. It only is showing up as its own connection. so I cant even get on the internet.
View 1 Replies
I am trying to setup my network in my home, so that I can extend the wireless signal from my main router by using an access point (a tenda w311r+).But, I want to do it so that the access point isn't connected to the main router with a cable, I want it to be connected to the main router wirelessly.It does say on the box that it can 'bridge' multiple wireless routers.
The access point I have also has 4 ethernet ports on it, so I will use one of these to plug my xbox 360 into.I also want the main router to be responsible for the DHCP.
Region : United Kingdom
Model : TL-WR702N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Using a TL-WR702N router as a wireless access point on a narrow-boat. How to print from my i Pad and iPhone to a printer on my narrow-boat, on the UK inland waterways. The Apple store geniuses seem to contradict each other on how it can be done, if at all. I have an i Pad and iPhone and would like to print photos, documents and the occasional web page to my Canon MG4250 printer, which has Air print capability, while I am cruising. I don't have a PC on the boat and of course there is no telephone or broadband connection (other than via 3G on my iPhone). In other words, I want to link my printer to a router, then when required, wireless connect to the router to print from my Apple devices.
Will the TP Link TL-WR702N 150Mbps Wireless N Nano Router allow me to do this? Reading the product information, this nano router looks very flexible, but all five modes mentioned seem to utilize an internet connection. I only have an internet connection via 3G on my iPhone, and can also tether the i Pad to the iPhone's WiFi hotspot to give internet connection on the i Pad. Would I have to use this internet connection somehow, or can I just connect the Apple devices to the printer via the WiFi on the nano router?
In effect I want to create a wireless access point for printing, without any, or at least a regular, internet connection.
Region : Argentina
Model : TL-WR740N
Hardware Version : V1
my tp link router not working due to firmware or any other problem i dont know.when i powered my device 4 number port light is blinking without inserting cable and admin penal not opening i also try 192.168.0.1 or tplinklogin.net
Region : Hungary
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : T-Home
I bought a TP-Link TL-WR740R Router, the setup went smoothly, I could connect to the internet and set up WiFi connection. But after a few hours, I accidentally unplugged the Ethernet cable from the router, and since then, I can't seem to make the router work. (I obviously plugged it back in.) Setup says I have a problem with the WAN connection.I tried rebooting, resting, reconfiguring, cloning the MAC address.The router is sending packages, but receiving none. How could this happen just by unplugging the cable for a second?
-Region : Others
-Model : TL-WR740N
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP :
How can u acces to the setup TP-Link WR740N router who is WDS with other router ???
I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1
How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
How can u acces to the setup TP-Link WR740N router who is WDS with other router? I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1.How to enter in my TP-Link modem, or i can`t , only factory reset
i access points in our network.I want to connect with 3550 switch but access point is not working and getting the below error
controller port error.
IOS image --=c3550-i9q3l2-mz.121-20.EA1a.bin
Switch Model---WS-C3550-24PWR-SMI
I want to know ,this access point is supported on this switch ?
Region : Others
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version :
ISP :
after year and a half of using TL-WR741 ND router, it suddenly stop working during the night. I have no problems with router before this happened (I think only one or two reset in 1 year and 6 months). System led light does not flash (some sytem error) and I can't access to 192.168.1.1 router setup site. I tried almost everything, unplug power, reset etc. for almost 100 times, reconnect the router with modem and PC in all posible ways, but still can't establish connection or even access to router's setup. Obviusly internet works fine?
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : India
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP : BSNL
702N runs as repeater mode to W8968. In 702N > Maintenance > Diagnostic the ping work for Internal network but fail for external IPs. Most devices connected to 702 can access Internet fine. I have also tried Bridge and Client mode.
Ping to W8968
Code:
Pinging 10.0.0.1 with 64 bytes of data:
Reply from 10.0.0.1: bytes=64 time=1 TTL=64 seq=1
Ping to Internet
Code:
Pinging 8.8.8.8 with 64 bytes of data:
Request timed out.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedRegion : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.23
Firmware Version : TL-WR740N_V4_130104
ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
Region : Romania
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP : AKTA
Network isn't working on pc or on wireless devices. I restarted, reinstalled, rebooted but isn't working. LEDs light up normally but I don't receive internet connection on devices.
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI work in a small office/production building and lately we have been having problems with an unstable connection. We are using a Meraki MR24 access point in our warehouse, the connection always starts out strong but sooner or later everyone will briefly lose connection and the AP goes away, then comes back and we're reconnected at excellent connection again.
View 3 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI got a new Tenda W311R+ Wireless-N Broadband Router yesterday. I already have a wired broadband internet connection in my home with a Beetel 110TC1 modem. I did following:
1. Connected the Beetel modem to the Tenda router using an Ethernet cable
2. Connected the Tenda router to my PC using another Ethernet cable.
3. Went to 192.168.0.1 (as mentioned in the instructions sheet which came along with the router)
Now, what should I set as the access mode, ADSL Dial-up or DHCP? Are there any other settings I should change in order to enhance the speed? I have Windows XP SP3. Also, do I need my Beetel modem or can I use the router without it?
I bought this Tenda wifi router and connected it.It's a chinese one and the user interface is not much friendly. It works fine but sometimes if u play around with it u will lose the settings you inserted in to it and you will need to reconfigure it.
My problem is my ISP seems to renew the IP's issued to their customers automatically every 10 hrs from the last login. But every other router keeps the connection alive but my router doesn't. It needs to be restarted in order to get the internet back online.simply said,u need to restart the router every 10 hrs.
BTW Never buy Tenda routers.
We have a several WAP610N Access points in our company since a few months and immediately noticed that it has problems with the gateway when you set it to use a static IP. (the AP loses its gateway when you pull the power). Today I saw that there was a firmware update, and in the firmware release notes it stated that the problem with the missing gateway info on the status screen was solved.
This info is correct. After updating to 1.0.0.2 the gateway is shown in the status screen when you use a static IP, but the actual function of the gateway is still not working after restarting the AP! I already let our reseller create a support call with Linksys a few months ago, but in the end they told me this would probably not be fixed and that I had to use DHCP.
How do i have reset my trenda router without a disk?
View 3 Replies View Relatedcan i set up my W311R+ tenda wireless router without the software driver?
View 1 Replies View Relatedhow do i reset my password for y tenda wireless router w311r
View 1 Replies View RelatedI have a 1130 cisco access point,we are using this for wireless cisco IP phone connectivity to the network.Earlier access point was woring fine and we were able to make calls through IP phone.But we have relocated to new place.Now the access point is not working and we are not able to make the calls on the wireless IP phone as the access point is not working.But the access is in the netwrok and we are able to ping the IP address of the Access point.
We are contonuously getting the below loggs on Access point and the access point is getting power from the ethernet port of the switch not through the external powerr adaptor.
error message:
: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C
4507R (0012.7fb6.6e6c).
how to make this work.
Powerline not working on media in one room. My Setup: ATT DSL Modem: Westell 6500 w/ Linksys WRT54GS router
First powerline to mac (about 8 feet down hall) second powerline to pc (windows vista) (about 12 feet down hall) third powerline to media (Xbox 360, Sony blu ray, Apple TV) (about 45 feet down hall)
I've had Powerline PLE/S 300 setup for a couple years I think working perfectly. I it set up because my house is VERY solidly built and the G wireless cannot reach even the second room down the hall.
I recently got a wireless device and couldn't keep connection in the living room so I was going to add an access point and futzed with the router and everything went down. I got the router back up, disconnected the access point for good, but the Powerlines wouldn't connect. I upgraded the firmware then reset them and finally got Number 1 and Number two powerline online and working. But the farthest point (router at back of house, media at front) is the living room and none of the powerline boxes will work ON THE MEDIA.
I plug in the powerline and the home light comes up, I attached my laptop out there and I connected fine, then I connect one of the media players - the Xbox, apple or blue ray - and the home light goes out media will not connect and the laptop is knocked off. It does this every time now, same media players that worked perfectly before.
I bought a new router (Linksys E4200), wondering if the old just didn't have the signal strength and set that up very easily and the same thing happened - no powerlines work on the media in the living room. Mind you, I did take Apple to a closer room and hook it up to a powerline and it works!
As my Xbox died on one my attempts to plug it in to the powerline. So new xbox cannot connect either. I used to connect from xbox to the pc media center to watch recorded tv and this cannot be done wirelessly, even with the new dual band N router AND a new extender!
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP : CenturyLink
I've just received my new TL-WR702N that I want to use as a repeater (downstairs) for my router (upstairs). I've tried the configurations listed on the TP-Link website, but none of them give me internet access. In fact, the local area connection shows the TL-WR702N as an "unidentified network".
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Just got my new TP-Link device and intend to use it in client mode for my new audio receiver to connect to my home network.Trying to configure the device, and I cannot even access the online utility. I tried using the following address:
192.168.0.254
192.168.1.1
None of these seem to work. Tried on Chrome, then Internet Explorer and made sure that the web browser was not set to proxy (it was not set to this in the first place). The address just doesn't seem to connect, and I get a "This page cannot be displayed" note, as if I'm reaching a bad address.
Region : Philippines
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 120320
ISP : Smart Bro
i have a problem with my tp-link wr740n.everytime i restart or power up may computer. my internet is no internet access and the ip address is autoconfiguration ipv4 : 169.254.x.x but when i unplug the cable on router and plugin again. the internet is back. everyday is happening this no internet access and the ipv4 : 169.254.x.x?
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
I seted up router and i coud acces the utility window, then i switced from w7x32 to w7x64 and then i try to acces the utility window i can only see.Username or Password is incorrect.Is the "Caps Lock" enabled on your keyboard? The username and password must be lowercase, please ensure that the "Caps Lock" LED is disabled on your keyboard and try again.Forgot your username or password? Please reset the device to the factory default settings if you have forgotten your username or password. The default username and password are both set as "admin". The settings will be restored to factory default after the resetting.
How to restore the device to the factory default settings?Firstly locate the reset button on the rear panel of the unit, whilst the device is powered on press and hold the reset button for more than 5 seconds, the device will then reboot and restore itself to the factory default settings.no pop up window appears i tried looking this up and the closest thing i found was to un-check the proxy but its not checked so what should i do to be able to access utility window?
Region : Others
Model : TL-WR741ND
Hardware Version : V4.20.0
Firmware Version : 3.12.11
As you can see it's a simple network, I mostly use the network to share itunes library from PC CENTRAL to the other pcs, play games like counter strike and the like, and of course share the internet connection and copy files from one to another. I have to puntualize that all the computers are in the same room.Last week my mom bought a Toshiba Satellite and I bought a TP-LINK TL-WR741ND so she can work in her room (which is pretty far if I want to make a wire connection), so I installed the WiFi but now this is how my network looks like:> The case is that:
a) I can't access my toshiba from any other computer, but the toshiba can access any other using \192.168.1.# command.
b) The PC Central's iTunes library can be played in toshiba's itunes.
c) I can't make an HomeGroup between the two pcs running w7. Actually the only one pc I want to be working in LAN with the toshiba is PC Central, but as I said earlier, PC Central can't access toshiba.
The settings in the TL-WR740N are: WAN working as Dynamic IP (got IP 192.168.1.46 submask 255.255.255.0 and gateway empty), lan 192.168.0.1, (I can't make it to be 192.168.1.#, I think that's impossible cause it always gives me an error 5008). MAC filtering and that's the only thing I changed from default settings.
Region : Ireland
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
I am trying to setup my DVR for remote access but my public IP and the routers WAN are not the same?
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP :
I've setup my nano router in client mode and successfully connected it to my existing wireless network by manually setting it's IP address to 192.168.1.2. The existing router has the IP address 192.168.1.1.
I know this has worked as I'm able to access the web management page from any computer in the house by visiting the IP address 192.168.1.2. So far so good.
However, my problem is that the nano router cannot speak to the internet. If I login to the web management page and go to diagnostics, I can ping every other device on the network fine, but I can't ping anything outside the network (e.g. 8.8.8.8 or [URL].
I've tried in vain to get this setup correctly, all I can assume is that the nano router isn't correctly determining that the existing router (192.168.1.1) is where it should be routing all external requests and they're just getting lost, but there's no configuration for that on the web management pages.
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View Related
