I work in a small office/production building and lately we have been having problems with an unstable connection. We are using a Meraki MR24 access point in our warehouse, the connection always starts out strong but sooner or later everyone will briefly lose connection and the AP goes away, then comes back and we're reconnected at excellent connection again.
View 3 RepliesI have an asa 5585x cluster. I get ssh access but no console access on the standby unit.
On the active unit, when I try console access, ASA ask for a password. I have tried all the one that I have configured, but without success.
ASUS Notebook G60Vx Series
Windows 7 Home Premium 64-bit
Intel(R) WiFi Link 5100 AGN
A few days ago my internet suddenly stopped working. I plugged in the ethernet cord and everything worked fine. Checking the properties in the device manager showed the device was working properly, I also tried resetting it to make sure it was enabled but it did not work.
Upon troubleshooting, the "Windows Network Diagnostic" said the problems was that the Wireless adapter was not turned on. Using the switch on the front of the laptop as well as the function keys does nothing. Usually a graphic pops up showing if the WiFi is on or off, changinging transparent to show the WiFi is disabled. Now when I turn the switch on it always appears transparent, effectively going from off to off
So I know the computer reads both the function keys and the switch on the front but both methods never actually turns the adapter on. I just finished a system restore and nothing has changed
We have a several WAP610N Access points in our company since a few months and immediately noticed that it has problems with the gateway when you set it to use a static IP. (the AP loses its gateway when you pull the power). Today I saw that there was a firmware update, and in the firmware release notes it stated that the problem with the missing gateway info on the status screen was solved.
This info is correct. After updating to 1.0.0.2 the gateway is shown in the status screen when you use a static IP, but the actual function of the gateway is still not working after restarting the AP! I already let our reseller create a support call with Linksys a few months ago, but in the end they told me this would probably not be fixed and that I had to use DHCP.
I am trying to set up a Tenda 150mbps wireless Ap/Router.Im trying to set it up to use it as a range extender.I followed all the directions. I put it in wisp mode. It doesnt seem to be communicating with my Tenda wireless router. It only is showing up as its own connection. so I cant even get on the internet.
View 1 Replies View RelatedI have a 1130 cisco access point,we are using this for wireless cisco IP phone connectivity to the network.Earlier access point was woring fine and we were able to make calls through IP phone.But we have relocated to new place.Now the access point is not working and we are not able to make the calls on the wireless IP phone as the access point is not working.But the access is in the netwrok and we are able to ping the IP address of the Access point.
We are contonuously getting the below loggs on Access point and the access point is getting power from the ethernet port of the switch not through the external powerr adaptor.
error message:
: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C
4507R (0012.7fb6.6e6c).
how to make this work.
Powerline not working on media in one room. My Setup: ATT DSL Modem: Westell 6500 w/ Linksys WRT54GS router
First powerline to mac (about 8 feet down hall) second powerline to pc (windows vista) (about 12 feet down hall) third powerline to media (Xbox 360, Sony blu ray, Apple TV) (about 45 feet down hall)
I've had Powerline PLE/S 300 setup for a couple years I think working perfectly. I it set up because my house is VERY solidly built and the G wireless cannot reach even the second room down the hall.
I recently got a wireless device and couldn't keep connection in the living room so I was going to add an access point and futzed with the router and everything went down. I got the router back up, disconnected the access point for good, but the Powerlines wouldn't connect. I upgraded the firmware then reset them and finally got Number 1 and Number two powerline online and working. But the farthest point (router at back of house, media at front) is the living room and none of the powerline boxes will work ON THE MEDIA.
I plug in the powerline and the home light comes up, I attached my laptop out there and I connected fine, then I connect one of the media players - the Xbox, apple or blue ray - and the home light goes out media will not connect and the laptop is knocked off. It does this every time now, same media players that worked perfectly before.
I bought a new router (Linksys E4200), wondering if the old just didn't have the signal strength and set that up very easily and the same thing happened - no powerlines work on the media in the living room. Mind you, I did take Apple to a closer room and hook it up to a powerline and it works!
As my Xbox died on one my attempts to plug it in to the powerline. So new xbox cannot connect either. I used to connect from xbox to the pc media center to watch recorded tv and this cannot be done wirelessly, even with the new dual band N router AND a new extender!
i access points in our network.I want to connect with 3550 switch but access point is not working and getting the below error
controller port error.
IOS image --=c3550-i9q3l2-mz.121-20.EA1a.bin
Switch Model---WS-C3550-24PWR-SMI
I want to know ,this access point is supported on this switch ?
Here at home I have great WIFI connectivity but on my main PC that is hard wired into the modem I have no Internet access. My service seems fine as my cable/VOIP telephone/wifi work great. I'm not sure how to detect my ISP settings. In 'device manager' it shows that the teredo tunneling adapter will not start. I don't know what that is or if its important here.
View 14 Replies View RelatedI have changed the channels, changed the firmware, changed the position of the wireless router, reinserted my wireless card on my rig, changed the security, turned everything setting on or off.
View 2 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHad a look inside my HP Pavilion p6685l recently and found there wasn't any wifi card which was odd because it's been working fine for months.Device Manager says theres a 802.11n Wireless Lan Card in there but I traced the wires from the ariel to a chip on the board (MSI 2A9C according to Belarc ). Property sheet says it's a Ralink Card and so does the vendor id ( 1814 ) but the device id (3092) belongs to an Intel I20 1.5 Raid Controller which is where I got lost. I didn't know Raid Controllers did wifi.
View 14 Replies View RelatedI'm staying n hotel, its having secured wirless netwrk, but its not working in my windows 7 64 bit, but it works in 32 bit..
View 1 Replies View RelatedI'll be downloading off of newsgroups and be pulling 3-4 MB/sec, no problems. My downloads are charted so I can see my speed never drops at all.but my web browsing will just STOP, for ~30 seconds. I'll have multiple tabs just STOP and crap out, while my downloads run fine. This also happens when I'm not downloading, so I know it's not a bandwidth issue,i assumed it was a router issue until I replaced my router and am getting the same issue.
View 1 Replies View RelatedEthernet stop working, but the wireless is fine, check in the device manger for any conflics none. open the network sharing centre and ran the truoble shooting utiiity and message came up with ethernet cable not plug in or brocken, which i have change it for a new one so its not the cable and its not the routor because B.T just gave me the new B.T Hub3, this network adaptor is on board and i have a wireless card in the PCI slot and the is a new main board which i built, everything was fine afew months ago til this started to acur
View 4 Replies View RelatedNothing seems to be able to connect to my wireless network. It seems to have occurred after I installed a new copy of windows 7 onto my sister's desktop. A message appeared saying we have the same ip address. I've tried renewing our ip address on both desktop but it won't give us new ip address for some reason.
View 14 Replies View RelatedWe have FIOS at our home. All the wall connections for ethernet are wired to the control panel in our house which are then connected to a wired router. We have another wireless router in the upstairs which gets internet through the wall port and it works fine.We had another downstairs wireless router in the living room that was working fine as well, but I reset it for certain reasons and it no longer works properly. All the proper lights light up: internet, port, power but the computer can only connect to the network and not the internet for some reason.
View 9 Replies View Relatedi share internet with my neighbor (we split the bill) and every so often like in the last 2 days, and usually not again for another 3 weeks for 2-3 more more days each time, am not able to browse(ff, chrome, ie) or use windows live messenger, but yet if i turn on bittorrent, the downloads are fine, the trackers don't update, but DHT and peer exchange update fine.And also, i can get on Gameranger (which uses UDP port 16000) and play games, and this happens to all 5 computers on the network, (4 wireless at my house[3 XPs 1 Win7] and one wired at her house[Win 7]), so it's not something on the computer, also, usually when i check my router the subnet is usually 255.255.255.0 but this morning before i came to work i noticed it was 255.0.0.0 , not sure if that matters, this has been happening for months, usually between every 3-4 weeks, we have no browser and msn use for 2-3 days?
View 1 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedHave a v2 E1200. Connect with PPPoE to ISP. IPv4 works fine. With firmware included on router, 2.0.01, it would receive a /64 of IPv6 from the ISP. This /64 would show up under 'status' / 'local network'. Although it did not seem to advertise this space to PC's on my network so I was unable to use it. I updated firmware to 2.0.04. Now it does not even pick up the IPv6 /64 at all.
Anyone have PPPoE and IPv6 working? Anywhere I can download 2.0.01 to try it again?
Is there a model of router that actually works with IPv6?
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : Alice (Telecom Italia)
I have just bought this new device, installed, DSL is working fine but not the USB printer sharing. Allways tells me: "This system was not supported yet." Here is the message box: usb_printer_error.JPG.I have a HP DeskJet 1050 and a Canon Pixma MP150 machine. I know, the HP is not in the supported printer list, indeed Canon is.
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
Daughter is at college with brand new Vostro 3450. Was working on school network during summer but drops the connection multiple times during the day. She runs the Troubleshooting which then allows her to connect and 30 minutes later the connection is dropped again. The laptop works fine when connected to the internet via the ethernet cable. Here is what has been done by the IT support at the school.
1 - Deleted the Intel wireless utility as they thought it was "fighting" with the Windows software for control over the wireless.
2 - Increased the power for the wireless card to "high performance".
3 - Reinstalled Windows 7 to eliminate that there is a software issue.
4 - Replaced the Intel Wireless Card with new part sent by Dell.
Now the IT supports recommendation is to "get a new system" and that perhaps the Vostro's wireless card is "not compatible with their network". For Dell computers they sell the Latitude to the students.
My daugther likes the Vostro. She doesn't want to give it up. Wants the system to work. She had the laptop during the summer session and had problems with connection. The Windows software was reinstalled thinking there was a virus (although no evidence of one) and then she had no connection problems for the whole summer. She came home for 2 weeks and returned back to school and then the system would not work again.
I don't know what to do. Can I buy a USB wireless adapter for her to temporarily use until I can figure out how to fix this problem. Personally, I think there is a design flaw with the vostro.
We have a pair of CSS 11503 installed in our DC. Stickiness is configured for one of the application since long back and was working pretty fine till last couple of months. Since last two months, we observed that CSS is not distributing sessions the way it suppose to be. Mostly, it forwards the session to same server even though request is coming from different sources. Once we refresh the sessions manually, it starts working fine. We have to do this exercise manually every alternate day.
View 1 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.