D-Link DSL-2750U - Connect Wireless Access Point To Modem
Jul 7, 2013
At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.
I have a situation where I have tenants connecting to my wireless network and paying towards the internet bill. I am able to control this by using MAC filtering, but I have just realised that this only works for wireless clients.
Is there a way to replicate this for the router's Lan ports? Or possibly even just disable Lan access. The router model is a D-link DSL-2750U.
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
I have D-link DSL 2750U wireless router. My PC and notebook are connected to router by Wi-Fi. They can share files or ping each other. I have a network storage unit plugged into router by an ethernet cable. Any of the computers cannot reach that storage unit or ping it. I guess my router isolates LAN network from WLAN network. Is there a way to combine them and get the router treat all devices connected to router in a single network?
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
I have set up an access point as per the instructions I found on this site. It works perfectly, holds a wireless signal fine. Now, I have the challenge of trying to remote connect to the home computer that is connected to this access point. I have absolutely no clue as to what changes in settings have to be made.
I started using a D-link 2750U wireless modem-router about 2 months ago, and configured it using the given disk for my ISP (MTNL Delhi). Since then, it has never retained a connection for more than 10 days, give or take i.e starts showing a red earth light instead of a green one. I usually reset it to factory settings and reconfigure it using the same disc over and over again, but now it has started dropping connection more frequently.Recently, it developed a new disease. Connection is very unstable now. Through line, it keeps disconnecting every 4-5 minutes. re-connects and dies again itself and does not work through wi-fi at allMy hardware quality healthy as I ran a wired connection for over 3 years without any trouble before this one.
I have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?
I'm trying to find out if it's possible to setup a 3600HGV (VDSL Gateway) as modem only and have a Netgear DGN3500 (ADSL2+) as a wireless access point. I'm aware that both are DSL modems, my reasoning for wanting to have them both hooked up is that
a) the 3600HGV has no Gigabit switch and runs on wireless G
b) the DGN 3500 has a Gigabit switch and does wireless N. So in a nutshell I want the 3600 as simple modem and the 3500 as a wireless N access point with Gigabit switch.
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine! The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Currently have a sbs2003 with 2 nics want to install a wireless access point for the internal network. the wireless router is on the external wan how do i link the access point to this?
So, in an attempt to improve my signal in my house I relocated my router upstairs from downstairs by running a long cable to the modem downstairs, since I have read that the signal travels more efficiently down than up apparently. That has not been the case. Now, I have two routers. A D-link DIR-655 and a Netgear router provided by Comcast which is a WNR-1000v2.
possible to set one of these routers up as a wireless access point? Have a router upstairs be the access point, and have a router downstairs connected to the modem. This sounds like this may be a solution but let me know if I'm completely wrong. In my mind, what I'm after is more of a range extender or a repeater but at this point I don't know the difference anymore. It's been quite stressful dealing with my old man for the past week because he can't use his iPad.
My modem and rotuer have double NAT. I am not the only one in my house so I can't mess with the router a lot, but turning the NAT off in my modem and assigning the new IP to my static IP router, by turning off DHCP in the router. Will make my modem a access point.
A friend of mine has a network with the following setup: D-Link DSL-2500U for ADSL, connected straight into a Telkom DG834GUv5 (locally rebadged Netgear) which has 2 PCs connected via cable, and 2 laptops via Wireless. A cable runs from the Telkom into a standard IPLink switch, which merely extends a cable into a D-Link DIR-615 running DD-WRT that has 2 computers connected, and shares wireless to a couple laptops.
At the moment the network is somewhat unstable, and recently the Telkom router has been giving serious problems, even after resetting to default. I want to try make the network a bit simpler and more stable. Firstly, I want to remove the IPLink switch, which merely extends the cable. Is an Ethernet Coupler what I need? Both cables are definitely under 100m combined (probably under 50m).
Now the big thing is a replacement for the Telkom (rebadged NetGear). Should I get another D-Link DIR-615 or is there a better solution? Their budget is between $40 and $60 US. Is it best to stick to the same brand, considering both devices are D-Link at present?
I bought the DIR 655 to put into our network as the Netopia wireless fails to connect even though we have maximum signal strength. Att advised that buying a third party router would solve this problem.I did manage to almost configure the DIR 655. I would have to connect it to the system to test it[CODE]
I have two DIR-655s. One is my main router, connected to my modem. The other, on the other side of the house, is set up as an access point. I followed this guide to set up my AP: [URL]
Both are are hard wired. I have both of them using the same SSID. Both are 802.11g only, have the same security mode, and key. The only wireless difference is the channel. One uses 6, while the other uses 11.
On initial setup, everything is fine, but after a few hours, the AP just seems to stop broadcasting a signal. I'm using "Wifi Analyzer" on Android to monitor it. When I look at the AP, the wifi indicator light is still on. If I log into it, change the channel, and press save on the "Wireless Settings" screen, it will broadcast for a few more hours before stopping again. The wired connect of this AP always seems to work (Xbox is hard wired to it).
AP Hardware Version: B1 / Firmware Version: 2.03NA
So I've decided to use a different router to resolve some VPN issues, and want to use my DIR-655 as a pure wireless access point. I need the access point to use the same range of IP addresses as the rest of the network (maintain access to networked printers, file shares, etc). However, I can't establish a wireless connection to the access point.
- Defined a IP address for the DIR-655 within the DHCP range of the primary router - Defined the proper subnet - Disabled the DHCP server on the DIR-655 - Connect a LAN port of the DIR-655 to a LAN port on a switch (note that it's not connected directly to a router).
When I connect a device WIRED to a LAN port on the DIR-655, everything works fine. The device gets assigned a DHCP address (which I know is being assigned by the main router since the DIR-655 DHCP server is disabled), and I can connect to the LAN and I can access the internet with no problem. So I know the DIR-655 is acting correctly to pass thru traffic. Also, I can access the DIR-655 web configuration page from any LAN device (even a device not directly connected to the DIR-655), so I know the DIR-655 is on that LAN correctly.
But when I try to connect WIRELESS to the DIR-655, it doesn't work at all. Although the wireless NIC is connecting to the DIR-655 (e.g. it asks me for the WPA key), it can't pull an IP address, so there is no connection to the LAN or internet.
So just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
I have a linksys e1000 modem router as the wireless internet connection in my home, now I bought a new one linksys e1000 to use it as an access point to cover the uncovered area, How can I do that?
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
I recently switched from DSL to cable. No issues on DSL. Since switching to cable, I haven't been able to connect more than one computer to the wireless access point at one time. I have three computers, one running W7, one on xp, and one on Vista. All three of the computers have been able to connect to the WAP when connecting alone.I am using a wap54g linksys access point. Setup is internet --> coax --> cable modem --> ethernet --> wap[CODE]
Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : 3.13.23 Build 120810 Rel 44064nHow do I configure the TP-Link N750 wireless router model TL-WDR4300 as an access point so that computers/nodes on the WAN, LAN and wifi connections of this device are all on the same network/subnet?From the admin browser page, disabling DHCP and NAT does not provide the desired results.
Region : United Kingdom Model : TL-WR702N Hardware Version : V4.20.0 Firmware Version : ISP :
Using a TL-WR702N router as a wireless access point on a narrow-boat. How to print from my i Pad and iPhone to a printer on my narrow-boat, on the UK inland waterways. The Apple store geniuses seem to contradict each other on how it can be done, if at all. I have an i Pad and iPhone and would like to print photos, documents and the occasional web page to my Canon MG4250 printer, which has Air print capability, while I am cruising. I don't have a PC on the boat and of course there is no telephone or broadband connection (other than via 3G on my iPhone). In other words, I want to link my printer to a router, then when required, wireless connect to the router to print from my Apple devices.
Will the TP Link TL-WR702N 150Mbps Wireless N Nano Router allow me to do this? Reading the product information, this nano router looks very flexible, but all five modes mentioned seem to utilize an internet connection. I only have an internet connection via 3G on my iPhone, and can also tether the i Pad to the iPhone's WiFi hotspot to give internet connection on the i Pad. Would I have to use this internet connection somehow, or can I just connect the Apple devices to the printer via the WiFi on the nano router?
In effect I want to create a wireless access point for printing, without any, or at least a regular, internet connection.
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
